drivers/infiniband/hw/ipath/ipath_iba6110.c

   1 /*
   2  * Copyright (c) 2006 QLogic, Inc. All rights reserved.
   3  * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
   4  *
   5  * This software is available to you under a choice of one of two
   6  * licenses.  You may choose to be licensed under the terms of the GNU
   7  * General Public License (GPL) Version 2, available from the file
   8  * COPYING in the main directory of this source tree, or the
   9  * OpenIB.org BSD license below:
  10  *
  11  *     Redistribution and use in source and binary forms, with or
  12  *     without modification, are permitted provided that the following
  13  *     conditions are met:
  14  *
  15  *      - Redistributions of source code must retain the above
  16  *        copyright notice, this list of conditions and the following
  17  *        disclaimer.
  18  *
  19  *      - Redistributions in binary form must reproduce the above
  20  *        copyright notice, this list of conditions and the following
  21  *        disclaimer in the documentation and/or other materials
  22  *        provided with the distribution.
  23  *
  24  * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
  25  * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
  26  * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
  27  * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
  28  * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
  29  * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
  30  * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
  31  * SOFTWARE.
  32  */
  33
  34 /*
  35  * This file contains all of the code that is specific to the InfiniPath
  36  * HT chip.
  37  */
  38
  39 #include <linux/pci.h>
  40 #include <linux/delay.h>
  41
  42 #include "ipath_kernel.h"
  43 #include "ipath_registers.h"
  44
  45 /*
  46  * This lists the InfiniPath registers, in the actual chip layout.
  47  * This structure should never be directly accessed.
  48  *
  49  * The names are in InterCap form because they're taken straight from
  50  * the chip specification.  Since they're only used in this file, they
  51  * don't pollute the rest of the source.
  52 */
  53
  54 struct _infinipath_do_not_use_kernel_regs {
  55         unsigned long long Revision;
  56         unsigned long long Control;
  57         unsigned long long PageAlign;
  58         unsigned long long PortCnt;
  59         unsigned long long DebugPortSelect;
  60         unsigned long long DebugPort;
  61         unsigned long long SendRegBase;
  62         unsigned long long UserRegBase;
  63         unsigned long long CounterRegBase;
  64         unsigned long long Scratch;
  65         unsigned long long ReservedMisc1;
  66         unsigned long long InterruptConfig;
  67         unsigned long long IntBlocked;
  68         unsigned long long IntMask;
  69         unsigned long long IntStatus;
  70         unsigned long long IntClear;
  71         unsigned long long ErrorMask;
  72         unsigned long long ErrorStatus;
  73         unsigned long long ErrorClear;
  74         unsigned long long HwErrMask;
  75         unsigned long long HwErrStatus;
  76         unsigned long long HwErrClear;
  77         unsigned long long HwDiagCtrl;
  78         unsigned long long MDIO;
  79         unsigned long long IBCStatus;
  80         unsigned long long IBCCtrl;
  81         unsigned long long ExtStatus;
  82         unsigned long long ExtCtrl;
  83         unsigned long long GPIOOut;
  84         unsigned long long GPIOMask;
  85         unsigned long long GPIOStatus;
  86         unsigned long long GPIOClear;
  87         unsigned long long RcvCtrl;
  88         unsigned long long RcvBTHQP;
  89         unsigned long long RcvHdrSize;
  90         unsigned long long RcvHdrCnt;
  91         unsigned long long RcvHdrEntSize;
  92         unsigned long long RcvTIDBase;
  93         unsigned long long RcvTIDCnt;
  94         unsigned long long RcvEgrBase;
  95         unsigned long long RcvEgrCnt;
  96         unsigned long long RcvBufBase;
  97         unsigned long long RcvBufSize;
  98         unsigned long long RxIntMemBase;
  99         unsigned long long RxIntMemSize;
 100         unsigned long long RcvPartitionKey;
 101         unsigned long long ReservedRcv[10];
 102         unsigned long long SendCtrl;
 103         unsigned long long SendPIOBufBase;
 104         unsigned long long SendPIOSize;
 105         unsigned long long SendPIOBufCnt;
 106         unsigned long long SendPIOAvailAddr;
 107         unsigned long long TxIntMemBase;
 108         unsigned long long TxIntMemSize;
 109         unsigned long long ReservedSend[9];
 110         unsigned long long SendBufferError;
 111         unsigned long long SendBufferErrorCONT1;
 112         unsigned long long SendBufferErrorCONT2;
 113         unsigned long long SendBufferErrorCONT3;
 114         unsigned long long ReservedSBE[4];
 115         unsigned long long RcvHdrAddr0;
 116         unsigned long long RcvHdrAddr1;
 117         unsigned long long RcvHdrAddr2;
 118         unsigned long long RcvHdrAddr3;
 119         unsigned long long RcvHdrAddr4;
 120         unsigned long long RcvHdrAddr5;
 121         unsigned long long RcvHdrAddr6;
 122         unsigned long long RcvHdrAddr7;
 123         unsigned long long RcvHdrAddr8;
 124         unsigned long long ReservedRHA[7];
 125         unsigned long long RcvHdrTailAddr0;
 126         unsigned long long RcvHdrTailAddr1;
 127         unsigned long long RcvHdrTailAddr2;
 128         unsigned long long RcvHdrTailAddr3;
 129         unsigned long long RcvHdrTailAddr4;
 130         unsigned long long RcvHdrTailAddr5;
 131         unsigned long long RcvHdrTailAddr6;
 132         unsigned long long RcvHdrTailAddr7;
 133         unsigned long long RcvHdrTailAddr8;
 134         unsigned long long ReservedRHTA[7];
 135         unsigned long long Sync;        /* Software only */
 136         unsigned long long Dump;        /* Software only */
 137         unsigned long long SimVer;      /* Software only */
 138         unsigned long long ReservedSW[5];
 139         unsigned long long SerdesConfig0;
 140         unsigned long long SerdesConfig1;
 141         unsigned long long SerdesStatus;
 142         unsigned long long XGXSConfig;
 143         unsigned long long ReservedSW2[4];
 144 };
 145
 146 #define IPATH_KREG_OFFSET(field) (offsetof(struct \
 147     _infinipath_do_not_use_kernel_regs, field) / sizeof(u64))
 148 #define IPATH_CREG_OFFSET(field) (offsetof( \
 149     struct infinipath_counters, field) / sizeof(u64))
 150
 151 static const struct ipath_kregs ipath_ht_kregs = {
 152         .kr_control = IPATH_KREG_OFFSET(Control),
 153         .kr_counterregbase = IPATH_KREG_OFFSET(CounterRegBase),
 154         .kr_debugport = IPATH_KREG_OFFSET(DebugPort),
 155         .kr_debugportselect = IPATH_KREG_OFFSET(DebugPortSelect),
 156         .kr_errorclear = IPATH_KREG_OFFSET(ErrorClear),
 157         .kr_errormask = IPATH_KREG_OFFSET(ErrorMask),
 158         .kr_errorstatus = IPATH_KREG_OFFSET(ErrorStatus),
 159         .kr_extctrl = IPATH_KREG_OFFSET(ExtCtrl),
 160         .kr_extstatus = IPATH_KREG_OFFSET(ExtStatus),
 161         .kr_gpio_clear = IPATH_KREG_OFFSET(GPIOClear),
 162         .kr_gpio_mask = IPATH_KREG_OFFSET(GPIOMask),
 163         .kr_gpio_out = IPATH_KREG_OFFSET(GPIOOut),
 164         .kr_gpio_status = IPATH_KREG_OFFSET(GPIOStatus),
 165         .kr_hwdiagctrl = IPATH_KREG_OFFSET(HwDiagCtrl),
 166         .kr_hwerrclear = IPATH_KREG_OFFSET(HwErrClear),
 167         .kr_hwerrmask = IPATH_KREG_OFFSET(HwErrMask),
 168         .kr_hwerrstatus = IPATH_KREG_OFFSET(HwErrStatus),
 169         .kr_ibcctrl = IPATH_KREG_OFFSET(IBCCtrl),
 170         .kr_ibcstatus = IPATH_KREG_OFFSET(IBCStatus),
 171         .kr_intblocked = IPATH_KREG_OFFSET(IntBlocked),
 172         .kr_intclear = IPATH_KREG_OFFSET(IntClear),
 173         .kr_interruptconfig = IPATH_KREG_OFFSET(InterruptConfig),
 174         .kr_intmask = IPATH_KREG_OFFSET(IntMask),
 175         .kr_intstatus = IPATH_KREG_OFFSET(IntStatus),
 176         .kr_mdio = IPATH_KREG_OFFSET(MDIO),
 177         .kr_pagealign = IPATH_KREG_OFFSET(PageAlign),
 178         .kr_partitionkey = IPATH_KREG_OFFSET(RcvPartitionKey),
 179         .kr_portcnt = IPATH_KREG_OFFSET(PortCnt),
 180         .kr_rcvbthqp = IPATH_KREG_OFFSET(RcvBTHQP),
 181         .kr_rcvbufbase = IPATH_KREG_OFFSET(RcvBufBase),
 182         .kr_rcvbufsize = IPATH_KREG_OFFSET(RcvBufSize),
 183         .kr_rcvctrl = IPATH_KREG_OFFSET(RcvCtrl),
 184         .kr_rcvegrbase = IPATH_KREG_OFFSET(RcvEgrBase),
 185         .kr_rcvegrcnt = IPATH_KREG_OFFSET(RcvEgrCnt),
 186         .kr_rcvhdrcnt = IPATH_KREG_OFFSET(RcvHdrCnt),
 187         .kr_rcvhdrentsize = IPATH_KREG_OFFSET(RcvHdrEntSize),
 188         .kr_rcvhdrsize = IPATH_KREG_OFFSET(RcvHdrSize),
 189         .kr_rcvintmembase = IPATH_KREG_OFFSET(RxIntMemBase),
 190         .kr_rcvintmemsize = IPATH_KREG_OFFSET(RxIntMemSize),
 191         .kr_rcvtidbase = IPATH_KREG_OFFSET(RcvTIDBase),
 192         .kr_rcvtidcnt = IPATH_KREG_OFFSET(RcvTIDCnt),
 193         .kr_revision = IPATH_KREG_OFFSET(Revision),
 194         .kr_scratch = IPATH_KREG_OFFSET(Scratch),
 195         .kr_sendbuffererror = IPATH_KREG_OFFSET(SendBufferError),
 196         .kr_sendctrl = IPATH_KREG_OFFSET(SendCtrl),
 197         .kr_sendpioavailaddr = IPATH_KREG_OFFSET(SendPIOAvailAddr),
 198         .kr_sendpiobufbase = IPATH_KREG_OFFSET(SendPIOBufBase),
 199         .kr_sendpiobufcnt = IPATH_KREG_OFFSET(SendPIOBufCnt),
 200         .kr_sendpiosize = IPATH_KREG_OFFSET(SendPIOSize),
 201         .kr_sendregbase = IPATH_KREG_OFFSET(SendRegBase),
 202         .kr_txintmembase = IPATH_KREG_OFFSET(TxIntMemBase),
 203         .kr_txintmemsize = IPATH_KREG_OFFSET(TxIntMemSize),
 204         .kr_userregbase = IPATH_KREG_OFFSET(UserRegBase),
 205         .kr_serdesconfig0 = IPATH_KREG_OFFSET(SerdesConfig0),
 206         .kr_serdesconfig1 = IPATH_KREG_OFFSET(SerdesConfig1),
 207         .kr_serdesstatus = IPATH_KREG_OFFSET(SerdesStatus),
 208         .kr_xgxsconfig = IPATH_KREG_OFFSET(XGXSConfig),
 209         /*
 210          * These should not be used directly via ipath_read_kreg64(),
 211          * use them with ipath_read_kreg64_port(),
 212          */
 213         .kr_rcvhdraddr = IPATH_KREG_OFFSET(RcvHdrAddr0),
 214         .kr_rcvhdrtailaddr = IPATH_KREG_OFFSET(RcvHdrTailAddr0)
 215 };
 216
 217 static const struct ipath_cregs ipath_ht_cregs = {
 218         .cr_badformatcnt = IPATH_CREG_OFFSET(RxBadFormatCnt),
 219         .cr_erricrccnt = IPATH_CREG_OFFSET(RxICRCErrCnt),
 220         .cr_errlinkcnt = IPATH_CREG_OFFSET(RxLinkProblemCnt),
 221         .cr_errlpcrccnt = IPATH_CREG_OFFSET(RxLPCRCErrCnt),
 222         .cr_errpkey = IPATH_CREG_OFFSET(RxPKeyMismatchCnt),
 223         .cr_errrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowCtrlErrCnt),
 224         .cr_err_rlencnt = IPATH_CREG_OFFSET(RxLenErrCnt),
 225         .cr_errslencnt = IPATH_CREG_OFFSET(TxLenErrCnt),
 226         .cr_errtidfull = IPATH_CREG_OFFSET(RxTIDFullErrCnt),
 227         .cr_errtidvalid = IPATH_CREG_OFFSET(RxTIDValidErrCnt),
 228         .cr_errvcrccnt = IPATH_CREG_OFFSET(RxVCRCErrCnt),
 229         .cr_ibstatuschange = IPATH_CREG_OFFSET(IBStatusChangeCnt),
 230         /* calc from Reg_CounterRegBase + offset */
 231         .cr_intcnt = IPATH_CREG_OFFSET(LBIntCnt),
 232         .cr_invalidrlencnt = IPATH_CREG_OFFSET(RxMaxMinLenErrCnt),
 233         .cr_invalidslencnt = IPATH_CREG_OFFSET(TxMaxMinLenErrCnt),
 234         .cr_lbflowstallcnt = IPATH_CREG_OFFSET(LBFlowStallCnt),
 235         .cr_pktrcvcnt = IPATH_CREG_OFFSET(RxDataPktCnt),
 236         .cr_pktrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowPktCnt),
 237         .cr_pktsendcnt = IPATH_CREG_OFFSET(TxDataPktCnt),
 238         .cr_pktsendflowcnt = IPATH_CREG_OFFSET(TxFlowPktCnt),
 239         .cr_portovflcnt = IPATH_CREG_OFFSET(RxP0HdrEgrOvflCnt),
 240         .cr_rcvebpcnt = IPATH_CREG_OFFSET(RxEBPCnt),
 241         .cr_rcvovflcnt = IPATH_CREG_OFFSET(RxBufOvflCnt),
 242         .cr_senddropped = IPATH_CREG_OFFSET(TxDroppedPktCnt),
 243         .cr_sendstallcnt = IPATH_CREG_OFFSET(TxFlowStallCnt),
 244         .cr_sendunderruncnt = IPATH_CREG_OFFSET(TxUnderrunCnt),
 245         .cr_wordrcvcnt = IPATH_CREG_OFFSET(RxDwordCnt),
 246         .cr_wordsendcnt = IPATH_CREG_OFFSET(TxDwordCnt),
 247         .cr_unsupvlcnt = IPATH_CREG_OFFSET(TxUnsupVLErrCnt),
 248         .cr_rxdroppktcnt = IPATH_CREG_OFFSET(RxDroppedPktCnt),
 249         .cr_iblinkerrrecovcnt = IPATH_CREG_OFFSET(IBLinkErrRecoveryCnt),
 250         .cr_iblinkdowncnt = IPATH_CREG_OFFSET(IBLinkDownedCnt),
 251         .cr_ibsymbolerrcnt = IPATH_CREG_OFFSET(IBSymbolErrCnt)
 252 };
 253
 254 /* kr_intstatus, kr_intclear, kr_intmask bits */
 255 #define INFINIPATH_I_RCVURG_MASK 0x1FF
 256 #define INFINIPATH_I_RCVAVAIL_MASK 0x1FF
 257
 258 /* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */
 259 #define INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT 0
 260 #define INFINIPATH_HWE_HTCMEMPARITYERR_MASK 0x3FFFFFULL
 261 #define INFINIPATH_HWE_HTCLNKABYTE0CRCERR   0x0000000000800000ULL
 262 #define INFINIPATH_HWE_HTCLNKABYTE1CRCERR   0x0000000001000000ULL
 263 #define INFINIPATH_HWE_HTCLNKBBYTE0CRCERR   0x0000000002000000ULL
 264 #define INFINIPATH_HWE_HTCLNKBBYTE1CRCERR   0x0000000004000000ULL
 265 #define INFINIPATH_HWE_HTCMISCERR4          0x0000000008000000ULL
 266 #define INFINIPATH_HWE_HTCMISCERR5          0x0000000010000000ULL
 267 #define INFINIPATH_HWE_HTCMISCERR6          0x0000000020000000ULL
 268 #define INFINIPATH_HWE_HTCMISCERR7          0x0000000040000000ULL
 269 #define INFINIPATH_HWE_HTCBUSTREQPARITYERR  0x0000000080000000ULL
 270 #define INFINIPATH_HWE_HTCBUSTRESPPARITYERR 0x0000000100000000ULL
 271 #define INFINIPATH_HWE_HTCBUSIREQPARITYERR  0x0000000200000000ULL
 272 #define INFINIPATH_HWE_COREPLL_FBSLIP       0x0080000000000000ULL
 273 #define INFINIPATH_HWE_COREPLL_RFSLIP       0x0100000000000000ULL
 274 #define INFINIPATH_HWE_HTBPLL_FBSLIP        0x0200000000000000ULL
 275 #define INFINIPATH_HWE_HTBPLL_RFSLIP        0x0400000000000000ULL
 276 #define INFINIPATH_HWE_HTAPLL_FBSLIP        0x0800000000000000ULL
 277 #define INFINIPATH_HWE_HTAPLL_RFSLIP        0x1000000000000000ULL
 278 #define INFINIPATH_HWE_SERDESPLLFAILED      0x2000000000000000ULL
 279
 280 /* kr_extstatus bits */
 281 #define INFINIPATH_EXTS_FREQSEL 0x2
 282 #define INFINIPATH_EXTS_SERDESSEL 0x4
 283 #define INFINIPATH_EXTS_MEMBIST_ENDTEST     0x0000000000004000
 284 #define INFINIPATH_EXTS_MEMBIST_CORRECT     0x0000000000008000
 285
 286 /*
 287  * masks and bits that are different in different chips, or present only
 288  * in one
 289  */
 290 static const ipath_err_t infinipath_hwe_htcmemparityerr_mask =
 291     INFINIPATH_HWE_HTCMEMPARITYERR_MASK;
 292 static const ipath_err_t infinipath_hwe_htcmemparityerr_shift =
 293     INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT;
 294
 295 static const ipath_err_t infinipath_hwe_htclnkabyte0crcerr =
 296     INFINIPATH_HWE_HTCLNKABYTE0CRCERR;
 297 static const ipath_err_t infinipath_hwe_htclnkabyte1crcerr =
 298     INFINIPATH_HWE_HTCLNKABYTE1CRCERR;
 299 static const ipath_err_t infinipath_hwe_htclnkbbyte0crcerr =
 300     INFINIPATH_HWE_HTCLNKBBYTE0CRCERR;
 301 static const ipath_err_t infinipath_hwe_htclnkbbyte1crcerr =
 302     INFINIPATH_HWE_HTCLNKBBYTE1CRCERR;
 303
 304 #define _IPATH_GPIO_SDA_NUM 1
 305 #define _IPATH_GPIO_SCL_NUM 0
 306
 307 #define IPATH_GPIO_SDA \
 308         (1ULL << (_IPATH_GPIO_SDA_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
 309 #define IPATH_GPIO_SCL \
 310         (1ULL << (_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
 311
 312 /* keep the code below somewhat more readonable; not used elsewhere */
 313 #define _IPATH_HTLINK0_CRCBITS (infinipath_hwe_htclnkabyte0crcerr |     \
 314                                 infinipath_hwe_htclnkabyte1crcerr)
 315 #define _IPATH_HTLINK1_CRCBITS (infinipath_hwe_htclnkbbyte0crcerr |     \
 316                                 infinipath_hwe_htclnkbbyte1crcerr)
 317 #define _IPATH_HTLANE0_CRCBITS (infinipath_hwe_htclnkabyte0crcerr |     \
 318                                 infinipath_hwe_htclnkbbyte0crcerr)
 319 #define _IPATH_HTLANE1_CRCBITS (infinipath_hwe_htclnkabyte1crcerr |     \
 320                                 infinipath_hwe_htclnkbbyte1crcerr)
 321
 322 static void hwerr_crcbits(struct ipath_devdata *dd, ipath_err_t hwerrs,
 323                           char *msg, size_t msgl)
 324 {
 325         char bitsmsg[64];
 326         ipath_err_t crcbits = hwerrs &
 327                 (_IPATH_HTLINK0_CRCBITS | _IPATH_HTLINK1_CRCBITS);
 328         /* don't check if 8bit HT */
 329         if (dd->ipath_flags & IPATH_8BIT_IN_HT0)
 330                 crcbits &= ~infinipath_hwe_htclnkabyte1crcerr;
 331         /* don't check if 8bit HT */
 332         if (dd->ipath_flags & IPATH_8BIT_IN_HT1)
 333                 crcbits &= ~infinipath_hwe_htclnkbbyte1crcerr;
 334         /*
 335          * we'll want to ignore link errors on link that is
 336          * not in use, if any.  For now, complain about both
 337          */
 338         if (crcbits) {
 339                 u16 ctrl0, ctrl1;
 340                 snprintf(bitsmsg, sizeof bitsmsg,
 341                          "[HT%s lane %s CRC (%llx); ignore till reload]",
 342                          !(crcbits & _IPATH_HTLINK1_CRCBITS) ?
 343                          "0 (A)" : (!(crcbits & _IPATH_HTLINK0_CRCBITS)
 344                                     ? "1 (B)" : "0+1 (A+B)"),
 345                          !(crcbits & _IPATH_HTLANE1_CRCBITS) ? "0"
 346                          : (!(crcbits & _IPATH_HTLANE0_CRCBITS) ? "1" :
 347                             "0+1"), (unsigned long long) crcbits);
 348                 strlcat(msg, bitsmsg, msgl);
 349
 350                 /*
 351                  * print extra info for debugging.  slave/primary
 352                  * config word 4, 8 (link control 0, 1)
 353                  */
 354
 355                 if (pci_read_config_word(dd->pcidev,
 356                                          dd->ipath_ht_slave_off + 0x4,
 357                                          &ctrl0))
 358                         dev_info(&dd->pcidev->dev, "Couldn't read "
 359                                  "linkctrl0 of slave/primary "
 360                                  "config block\n");
 361                 else if (!(ctrl0 & 1 << 6))
 362                         /* not if EOC bit set */
 363                         ipath_dbg("HT linkctrl0 0x%x%s%s\n", ctrl0,
 364                                   ((ctrl0 >> 8) & 7) ? " CRC" : "",
 365                                   ((ctrl0 >> 4) & 1) ? "linkfail" :
 366                                   "");
 367                 if (pci_read_config_word(dd->pcidev,
 368                                          dd->ipath_ht_slave_off + 0x8,
 369                                          &ctrl1))
 370                         dev_info(&dd->pcidev->dev, "Couldn't read "
 371                                  "linkctrl1 of slave/primary "
 372                                  "config block\n");
 373                 else if (!(ctrl1 & 1 << 6))
 374                         /* not if EOC bit set */
 375                         ipath_dbg("HT linkctrl1 0x%x%s%s\n", ctrl1,
 376                                   ((ctrl1 >> 8) & 7) ? " CRC" : "",
 377                                   ((ctrl1 >> 4) & 1) ? "linkfail" :
 378                                   "");
 379
 380                 /* disable until driver reloaded */
 381                 dd->ipath_hwerrmask &= ~crcbits;
 382                 ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
 383                                  dd->ipath_hwerrmask);
 384                 ipath_dbg("HT crc errs: %s\n", msg);
 385         } else
 386                 ipath_dbg("ignoring HT crc errors 0x%llx, "
 387                           "not in use\n", (unsigned long long)
 388                           (hwerrs & (_IPATH_HTLINK0_CRCBITS |
 389                                      _IPATH_HTLINK1_CRCBITS)));
 390 }
 391
 392 /* 6110 specific hardware errors... */
 393 static const struct ipath_hwerror_msgs ipath_6110_hwerror_msgs[] = {
 394         INFINIPATH_HWE_MSG(HTCBUSIREQPARITYERR, "HTC Ireq Parity"),
 395         INFINIPATH_HWE_MSG(HTCBUSTREQPARITYERR, "HTC Treq Parity"),
 396         INFINIPATH_HWE_MSG(HTCBUSTRESPPARITYERR, "HTC Tresp Parity"),
 397         INFINIPATH_HWE_MSG(HTCMISCERR5, "HT core Misc5"),
 398         INFINIPATH_HWE_MSG(HTCMISCERR6, "HT core Misc6"),
 399         INFINIPATH_HWE_MSG(HTCMISCERR7, "HT core Misc7"),
 400         INFINIPATH_HWE_MSG(RXDSYNCMEMPARITYERR, "Rx Dsync"),
 401         INFINIPATH_HWE_MSG(SERDESPLLFAILED, "SerDes PLL"),
 402 };
 403
 404 /**
 405  * ipath_ht_handle_hwerrors - display hardware errors.
 406  * @dd: the infinipath device
 407  * @msg: the output buffer
 408  * @msgl: the size of the output buffer
 409  *
 410  * Use same msg buffer as regular errors to avoid excessive stack
 411  * use.  Most hardware errors are catastrophic, but for right now,
 412  * we'll print them and continue.  We reuse the same message buffer as
 413  * ipath_handle_errors() to avoid excessive stack usage.
 414  */
 415 static void ipath_ht_handle_hwerrors(struct ipath_devdata *dd, char *msg,
 416                                      size_t msgl)
 417 {
 418         ipath_err_t hwerrs;
 419         u32 bits, ctrl;
 420         int isfatal = 0;
 421         char bitsmsg[64];
 422
 423         hwerrs = ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus);
 424
 425         if (!hwerrs) {
 426                 ipath_cdbg(VERBOSE, "Called but no hardware errors set\n");
 427                 /*
 428                  * better than printing cofusing messages
 429                  * This seems to be related to clearing the crc error, or
 430                  * the pll error during init.
 431                  */
 432                 goto bail;
 433         } else if (hwerrs == -1LL) {
 434                 ipath_dev_err(dd, "Read of hardware error status failed "
 435                               "(all bits set); ignoring\n");
 436                 goto bail;
 437         }
 438         ipath_stats.sps_hwerrs++;
 439
 440         /* Always clear the error status register, except MEMBISTFAIL,
 441          * regardless of whether we continue or stop using the chip.
 442          * We want that set so we know it failed, even across driver reload.
 443          * We'll still ignore it in the hwerrmask.  We do this partly for
 444          * diagnostics, but also for support */
 445         ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
 446                          hwerrs&~INFINIPATH_HWE_MEMBISTFAILED);
 447
 448         hwerrs &= dd->ipath_hwerrmask;
 449
 450         /*
 451          * make sure we get this much out, unless told to be quiet,
 452          * or it's occurred within the last 5 seconds
 453          */
 454         if ((hwerrs & ~dd->ipath_lasthwerror) ||
 455             (ipath_debug & __IPATH_VERBDBG))
 456                 dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx "
 457                          "(cleared)\n", (unsigned long long) hwerrs);
 458         dd->ipath_lasthwerror |= hwerrs;
 459
 460         if (hwerrs & ~infinipath_hwe_bitsextant)
 461                 ipath_dev_err(dd, "hwerror interrupt with unknown errors "
 462                               "%llx set\n", (unsigned long long)
 463                               (hwerrs & ~infinipath_hwe_bitsextant));
 464
 465         ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control);
 466         if (ctrl & INFINIPATH_C_FREEZEMODE) {
 467                 if (hwerrs) {
 468                         /*
 469                          * if any set that we aren't ignoring; only
 470                          * make the complaint once, in case it's stuck
 471                          * or recurring, and we get here multiple
 472                          * times.
 473                          */
 474                         if (dd->ipath_flags & IPATH_INITTED) {
 475                                 ipath_dev_err(dd, "Fatal Hardware Error (freeze "
 476                                               "mode), no longer usable, SN %.16s\n",
 477                                                   dd->ipath_serial);
 478                                 isfatal = 1;
 479                         }
 480                         *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY;
 481                         /* mark as having had error */
 482                         *dd->ipath_statusp |= IPATH_STATUS_HWERROR;
 483                         /*
 484                          * mark as not usable, at a minimum until driver
 485                          * is reloaded, probably until reboot, since no
 486                          * other reset is possible.
 487                          */
 488                         dd->ipath_flags &= ~IPATH_INITTED;
 489                 } else {
 490                         ipath_dbg("Clearing freezemode on ignored hardware "
 491                                   "error\n");
 492                         ctrl &= ~INFINIPATH_C_FREEZEMODE;
 493                         ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
 494                                          ctrl);
 495                 }
 496         }
 497
 498         *msg = '\0';
 499
 500         /*
 501          * may someday want to decode into which bits are which
 502          * functional area for parity errors, etc.
 503          */
 504         if (hwerrs & (infinipath_hwe_htcmemparityerr_mask
 505                       << INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT)) {
 506                 bits = (u32) ((hwerrs >>
 507                                INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT) &
 508                               INFINIPATH_HWE_HTCMEMPARITYERR_MASK);
 509                 snprintf(bitsmsg, sizeof bitsmsg, "[HTC Parity Errs %x] ",
 510                          bits);
 511                 strlcat(msg, bitsmsg, msgl);
 512         }
 513
 514         ipath_format_hwerrors(hwerrs,
 515                               ipath_6110_hwerror_msgs,
 516                               sizeof(ipath_6110_hwerror_msgs) /
 517                               sizeof(ipath_6110_hwerror_msgs[0]),
 518                               msg, msgl);
 519
 520         if (hwerrs & (_IPATH_HTLINK0_CRCBITS | _IPATH_HTLINK1_CRCBITS))
 521                 hwerr_crcbits(dd, hwerrs, msg, msgl);
 522
 523         if (hwerrs & INFINIPATH_HWE_MEMBISTFAILED) {
 524                 strlcat(msg, "[Memory BIST test failed, InfiniPath hardware unusable]",
 525                         msgl);
 526                 /* ignore from now on, so disable until driver reloaded */
 527                 dd->ipath_hwerrmask &= ~INFINIPATH_HWE_MEMBISTFAILED;
 528                 ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
 529                                  dd->ipath_hwerrmask);
 530         }
 531 #define _IPATH_PLL_FAIL (INFINIPATH_HWE_COREPLL_FBSLIP |        \
 532                          INFINIPATH_HWE_COREPLL_RFSLIP |        \
 533                          INFINIPATH_HWE_HTBPLL_FBSLIP |         \
 534                          INFINIPATH_HWE_HTBPLL_RFSLIP |         \
 535                          INFINIPATH_HWE_HTAPLL_FBSLIP |         \
 536                          INFINIPATH_HWE_HTAPLL_RFSLIP)
 537
 538         if (hwerrs & _IPATH_PLL_FAIL) {
 539                 snprintf(bitsmsg, sizeof bitsmsg,
 540                          "[PLL failed (%llx), InfiniPath hardware unusable]",
 541                          (unsigned long long) (hwerrs & _IPATH_PLL_FAIL));
 542                 strlcat(msg, bitsmsg, msgl);
 543                 /* ignore from now on, so disable until driver reloaded */
 544                 dd->ipath_hwerrmask &= ~(hwerrs & _IPATH_PLL_FAIL);
 545                 ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
 546                                  dd->ipath_hwerrmask);
 547         }
 548
 549         if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED) {
 550                 /*
 551                  * If it occurs, it is left masked since the eternal
 552                  * interface is unused
 553                  */
 554                 dd->ipath_hwerrmask &= ~INFINIPATH_HWE_SERDESPLLFAILED;
 555                 ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
 556                                  dd->ipath_hwerrmask);
 557         }
 558
 559         ipath_dev_err(dd, "%s hardware error\n", msg);
 560         if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg)
 561                 /*
 562                  * for status file; if no trailing brace is copied,
 563                  * we'll know it was truncated.
 564                  */
 565                 snprintf(dd->ipath_freezemsg,
 566                          dd->ipath_freezelen, "{%s}", msg);
 567
 568 bail:;
 569 }
 570
 571 /**
 572  * ipath_ht_boardname - fill in the board name
 573  * @dd: the infinipath device
 574  * @name: the output buffer
 575  * @namelen: the size of the output buffer
 576  *
 577  * fill in the board name, based on the board revision register
 578  */
 579 static int ipath_ht_boardname(struct ipath_devdata *dd, char *name,
 580                               size_t namelen)
 581 {
 582         char *n = NULL;
 583         u8 boardrev = dd->ipath_boardrev;
 584         int ret;
 585
 586         switch (boardrev) {
 587         case 4:         /* Ponderosa is one of the bringup boards */
 588                 n = "Ponderosa";
 589                 break;
 590         case 5:
 591                 /*
 592                  * original production board; two production levels, with
 593                  * different serial number ranges.   See ipath_ht_early_init() for
 594                  * case where we enable IPATH_GPIO_INTR for later serial # range.
 595                  */
 596                 n = "InfiniPath_QHT7040";
 597                 break;
 598         case 6:
 599                 n = "OEM_Board_3";
 600                 break;
 601         case 7:
 602                 /* small form factor production board */
 603                 n = "InfiniPath_QHT7140";
 604                 break;
 605         case 8:
 606                 n = "LS/X-1";
 607                 break;
 608         case 9:         /* Comstock bringup test board */
 609                 n = "Comstock";
 610                 break;
 611         case 10:
 612                 n = "OEM_Board_2";
 613                 break;
 614         case 11:
 615                 n = "InfiniPath_HT-470"; /* obsoleted */
 616                 break;
 617         case 12:
 618                 n = "OEM_Board_4";
 619                 break;
 620         default:                /* don't know, just print the number */
 621                 ipath_dev_err(dd, "Don't yet know about board "
 622                               "with ID %u\n", boardrev);
 623                 snprintf(name, namelen, "Unknown_InfiniPath_QHT7xxx_%u",
 624                          boardrev);
 625                 break;
 626         }
 627         if (n)
 628                 snprintf(name, namelen, "%s", n);
 629
 630         if (dd->ipath_majrev != 3 || (dd->ipath_minrev < 2 || dd->ipath_minrev > 3)) {
 631                 /*
 632                  * This version of the driver only supports Rev 3.2 and 3.3
 633                  */
 634                 ipath_dev_err(dd,
 635                               "Unsupported InfiniPath hardware revision %u.%u!\n",
 636                               dd->ipath_majrev, dd->ipath_minrev);
 637                 ret = 1;
 638                 goto bail;
 639         }
 640         /*
 641          * pkt/word counters are 32 bit, and therefore wrap fast enough
 642          * that we snapshot them from a timer, and maintain 64 bit shadow
 643          * copies
 644          */
 645         dd->ipath_flags |= IPATH_32BITCOUNTERS;
 646         if (dd->ipath_htspeed != 800)
 647                 ipath_dev_err(dd,
 648                               "Incorrectly configured for HT @ %uMHz\n",
 649                               dd->ipath_htspeed);
 650         if (dd->ipath_boardrev == 7 || dd->ipath_boardrev == 11 ||
 651             dd->ipath_boardrev == 6)
 652                 dd->ipath_flags |= IPATH_GPIO_INTR;
 653         else
 654                 dd->ipath_flags |= IPATH_POLL_RX_INTR;
 655         if (dd->ipath_boardrev == 8) {  /* LS/X-1 */
 656                 u64 val;
 657                 val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
 658                 if (val & INFINIPATH_EXTS_SERDESSEL) {
 659                         /*
 660                          * hardware disabled
 661                          *
 662                          * This means that the chip is hardware disabled,
 663                          * and will not be able to bring up the link,
 664                          * in any case.  We special case this and abort
 665                          * early, to avoid later messages.  We also set
 666                          * the DISABLED status bit
 667                          */
 668                         ipath_dbg("Unit %u is hardware-disabled\n",
 669                                   dd->ipath_unit);
 670                         *dd->ipath_statusp |= IPATH_STATUS_DISABLED;
 671                         /* this value is handled differently */
 672                         ret = 2;
 673                         goto bail;
 674                 }
 675         }
 676         ret = 0;
 677
 678 bail:
 679         return ret;
 680 }
 681
 682 static void ipath_check_htlink(struct ipath_devdata *dd)
 683 {
 684         u8 linkerr, link_off, i;
 685
 686         for (i = 0; i < 2; i++) {
 687                 link_off = dd->ipath_ht_slave_off + i * 4 + 0xd;
 688                 if (pci_read_config_byte(dd->pcidev, link_off, &linkerr))
 689                         dev_info(&dd->pcidev->dev, "Couldn't read "
 690                                  "linkerror%d of HT slave/primary block\n",
 691                                  i);
 692                 else if (linkerr & 0xf0) {
 693                         ipath_cdbg(VERBOSE, "HT linkerr%d bits 0x%x set, "
 694                                    "clearing\n", linkerr >> 4, i);
 695                         /*
 696                          * writing the linkerr bits that are set should
 697                          * clear them
 698                          */
 699                         if (pci_write_config_byte(dd->pcidev, link_off,
 700                                                   linkerr))
 701                                 ipath_dbg("Failed write to clear HT "
 702                                           "linkerror%d\n", i);
 703                         if (pci_read_config_byte(dd->pcidev, link_off,
 704                                                  &linkerr))
 705                                 dev_info(&dd->pcidev->dev,
 706                                          "Couldn't reread linkerror%d of "
 707                                          "HT slave/primary block\n", i);
 708                         else if (linkerr & 0xf0)
 709                                 dev_info(&dd->pcidev->dev,
 710                                          "HT linkerror%d bits 0x%x "
 711                                          "couldn't be cleared\n",
 712                                          i, linkerr >> 4);
 713                 }
 714         }
 715 }
 716
 717 static int ipath_setup_ht_reset(struct ipath_devdata *dd)
 718 {
 719         ipath_dbg("No reset possible for this InfiniPath hardware\n");
 720         return 0;
 721 }
 722
 723 #define HT_INTR_DISC_CONFIG  0x80       /* HT interrupt and discovery cap */
 724 #define HT_INTR_REG_INDEX    2  /* intconfig requires indirect accesses */
 725
 726 /*
 727  * Bits 13-15 of command==0 is slave/primary block.  Clear any HT CRC
 728  * errors.  We only bother to do this at load time, because it's OK if
 729  * it happened before we were loaded (first time after boot/reset),
 730  * but any time after that, it's fatal anyway.  Also need to not check
 731  * for for upper byte errors if we are in 8 bit mode, so figure out
 732  * our width.  For now, at least, also complain if it's 8 bit.
 733  */
 734 static void slave_or_pri_blk(struct ipath_devdata *dd, struct pci_dev *pdev,
 735                              int pos, u8 cap_type)
 736 {
 737         u8 linkwidth = 0, linkerr, link_a_b_off, link_off;
 738         u16 linkctrl = 0;
 739         int i;
 740
 741         dd->ipath_ht_slave_off = pos;
 742         /* command word, master_host bit */
 743         /* master host || slave */
 744         if ((cap_type >> 2) & 1)
 745                 link_a_b_off = 4;
 746         else
 747                 link_a_b_off = 0;
 748         ipath_cdbg(VERBOSE, "HT%u (Link %c) connected to processor\n",
 749                    link_a_b_off ? 1 : 0,
 750                    link_a_b_off ? 'B' : 'A');
 751
 752         link_a_b_off += pos;
 753
 754         /*
 755          * check both link control registers; clear both HT CRC sets if
 756          * necessary.
 757          */
 758         for (i = 0; i < 2; i++) {
 759                 link_off = pos + i * 4 + 0x4;
 760                 if (pci_read_config_word(pdev, link_off, &linkctrl))
 761                         ipath_dev_err(dd, "Couldn't read HT link control%d "
 762                                       "register\n", i);
 763                 else if (linkctrl & (0xf << 8)) {
 764                         ipath_cdbg(VERBOSE, "Clear linkctrl%d CRC Error "
 765                                    "bits %x\n", i, linkctrl & (0xf << 8));
 766                         /*
 767                          * now write them back to clear the error.
 768                          */
 769                         pci_write_config_byte(pdev, link_off,
 770                                               linkctrl & (0xf << 8));
 771                 }
 772         }
 773
 774         /*
 775          * As with HT CRC bits, same for protocol errors that might occur
 776          * during boot.
 777          */
 778         for (i = 0; i < 2; i++) {
 779                 link_off = pos + i * 4 + 0xd;
 780                 if (pci_read_config_byte(pdev, link_off, &linkerr))
 781                         dev_info(&pdev->dev, "Couldn't read linkerror%d "
 782                                  "of HT slave/primary block\n", i);
 783                 else if (linkerr & 0xf0) {
 784                         ipath_cdbg(VERBOSE, "HT linkerr%d bits 0x%x set, "
 785                                    "clearing\n", linkerr >> 4, i);
 786                         /*
 787                          * writing the linkerr bits that are set will clear
 788                          * them
 789                          */
 790                         if (pci_write_config_byte
 791                             (pdev, link_off, linkerr))
 792                                 ipath_dbg("Failed write to clear HT "
 793                                           "linkerror%d\n", i);
 794                         if (pci_read_config_byte(pdev, link_off, &linkerr))
 795                                 dev_info(&pdev->dev, "Couldn't reread "
 796                                          "linkerror%d of HT slave/primary "
 797                                          "block\n", i);
 798                         else if (linkerr & 0xf0)
 799                                 dev_info(&pdev->dev, "HT linkerror%d bits "
 800                                          "0x%x couldn't be cleared\n",
 801                                          i, linkerr >> 4);
 802                 }
 803         }
 804
 805         /*
 806          * this is just for our link to the host, not devices connected
 807          * through tunnel.
 808          */
 809
 810         if (pci_read_config_byte(pdev, link_a_b_off + 7, &linkwidth))
 811                 ipath_dev_err(dd, "Couldn't read HT link width "
 812                               "config register\n");
 813         else {
 814                 u32 width;
 815                 switch (linkwidth & 7) {
 816                 case 5:
 817                         width = 4;
 818                         break;
 819                 case 4:
 820                         width = 2;
 821                         break;
 822                 case 3:
 823                         width = 32;
 824                         break;
 825                 case 1:
 826                         width = 16;
 827                         break;
 828                 case 0:
 829                 default:        /* if wrong, assume 8 bit */
 830                         width = 8;
 831                         break;
 832                 }
 833
 834                 dd->ipath_htwidth = width;
 835
 836                 if (linkwidth != 0x11) {
 837                         ipath_dev_err(dd, "Not configured for 16 bit HT "
 838                                       "(%x)\n", linkwidth);
 839                         if (!(linkwidth & 0xf)) {
 840                                 ipath_dbg("Will ignore HT lane1 errors\n");
 841                                 dd->ipath_flags |= IPATH_8BIT_IN_HT0;
 842                         }
 843                 }
 844         }
 845
 846         /*
 847          * this is just for our link to the host, not devices connected
 848          * through tunnel.
 849          */
 850         if (pci_read_config_byte(pdev, link_a_b_off + 0xd, &linkwidth))
 851                 ipath_dev_err(dd, "Couldn't read HT link frequency "
 852                               "config register\n");
 853         else {
 854                 u32 speed;
 855                 switch (linkwidth & 0xf) {
 856                 case 6:
 857                         speed = 1000;
 858                         break;
 859                 case 5:
 860                         speed = 800;
 861                         break;
 862                 case 4:
 863                         speed = 600;
 864                         break;
 865                 case 3:
 866                         speed = 500;
 867                         break;
 868                 case 2:
 869                         speed = 400;
 870                         break;
 871                 case 1:
 872                         speed = 300;
 873                         break;
 874                 default:
 875                         /*
 876                          * assume reserved and vendor-specific are 200...
 877                          */
 878                 case 0:
 879                         speed = 200;
 880                         break;
 881                 }
 882                 dd->ipath_htspeed = speed;
 883         }
 884 }
 885
 886 static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev,
 887                             int pos)
 888 {
 889         u32 int_handler_addr_lower;
 890         u32 int_handler_addr_upper;
 891         u64 ihandler;
 892         u32 intvec;
 893
 894         /* use indirection register to get the intr handler */
 895         pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x10);
 896         pci_read_config_dword(pdev, pos + 4, &int_handler_addr_lower);
 897         pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x11);
 898         pci_read_config_dword(pdev, pos + 4, &int_handler_addr_upper);
 899
 900         ihandler = (u64) int_handler_addr_lower |
 901                 ((u64) int_handler_addr_upper << 32);
 902
 903         /*
 904          * kernels with CONFIG_PCI_MSI set the vector in the irq field of
 905          * struct pci_device, so we use that to program the internal
 906          * interrupt register (not config space) with that value. The BIOS
 907          * must still have done the basic MSI setup.
 908          */
 909         intvec = pdev->irq;
 910         /*
 911          * clear any vector bits there; normally not set but we'll overload
 912          * this for some debug purposes (setting the HTC debug register
 913          * value from software, rather than GPIOs), so it might be set on a
 914          * driver reload.
 915          */
 916         ihandler &= ~0xff0000;
 917         /* x86 vector goes in intrinfo[23:16] */
 918         ihandler |= intvec << 16;
 919         ipath_cdbg(VERBOSE, "ihandler lower %x, upper %x, intvec %x, "
 920                    "interruptconfig %llx\n", int_handler_addr_lower,
 921                    int_handler_addr_upper, intvec,
 922                    (unsigned long long) ihandler);
 923
 924         /* can't program yet, so save for interrupt setup */
 925         dd->ipath_intconfig = ihandler;
 926         /* keep going, so we find link control stuff also */
 927
 928         return ihandler != 0;
 929 }
 930
 931 /**
 932  * ipath_setup_ht_config - setup the interruptconfig register
 933  * @dd: the infinipath device
 934  * @pdev: the PCI device
 935  *
 936  * setup the interruptconfig register from the HT config info.
 937  * Also clear CRC errors in HT linkcontrol, if necessary.
 938  * This is done only for the real hardware.  It is done before
 939  * chip address space is initted, so can't touch infinipath registers
 940  */
 941 static int ipath_setup_ht_config(struct ipath_devdata *dd,
 942                                  struct pci_dev *pdev)
 943 {
 944         int pos, ret = 0;
 945         int ihandler = 0;
 946
 947         /*
 948          * Read the capability info to find the interrupt info, and also
 949          * handle clearing CRC errors in linkctrl register if necessary.  We
 950          * do this early, before we ever enable errors or hardware errors,
 951          * mostly to avoid causing the chip to enter freeze mode.
 952          */
 953         pos = pci_find_capability(pdev, PCI_CAP_ID_HT);
 954         if (!pos) {
 955                 ipath_dev_err(dd, "Couldn't find HyperTransport "
 956                               "capability; no interrupts\n");
 957                 ret = -ENODEV;
 958                 goto bail;
 959         }
 960         do {
 961                 u8 cap_type;
 962
 963                 /* the HT capability type byte is 3 bytes after the
 964                  * capability byte.
 965                  */
 966                 if (pci_read_config_byte(pdev, pos + 3, &cap_type)) {
 967                         dev_info(&pdev->dev, "Couldn't read config "
 968                                  "command @ %d\n", pos);
 969                         continue;
 970                 }
 971                 if (!(cap_type & 0xE0))
 972                         slave_or_pri_blk(dd, pdev, pos, cap_type);
 973                 else if (cap_type == HT_INTR_DISC_CONFIG)
 974                         ihandler = set_int_handler(dd, pdev, pos);
 975         } while ((pos = pci_find_next_capability(pdev, pos,
 976                                                  PCI_CAP_ID_HT)));
 977
 978         if (!ihandler) {
 979                 ipath_dev_err(dd, "Couldn't find interrupt handler in "
 980                               "config space\n");
 981                 ret = -ENODEV;
 982         }
 983
 984 bail:
 985         return ret;
 986 }
 987
 988 /**
 989  * ipath_setup_ht_cleanup - clean up any per-chip chip-specific stuff
 990  * @dd: the infinipath device
 991  *
 992  * Called during driver unload.
 993  * This is currently a nop for the HT chip, not for all chips
 994  */
 995 static void ipath_setup_ht_cleanup(struct ipath_devdata *dd)
 996 {
 997 }
 998
 999 /**
1000  * ipath_setup_ht_setextled - set the state of the two external LEDs
1001  * @dd: the infinipath device
1002  * @lst: the L state
1003  * @ltst: the LT state
1004  *
1005  * Set the state of the two external LEDs, to indicate physical and
1006  * logical state of IB link.   For this chip (at least with recommended
1007  * board pinouts), LED1 is Green (physical state), and LED2 is Yellow
1008  * (logical state)
1009  *
1010  * Note:  We try to match the Mellanox HCA LED behavior as best
1011  * we can.  Green indicates physical link state is OK (something is
1012  * plugged in, and we can train).
1013  * Amber indicates the link is logically up (ACTIVE).
1014  * Mellanox further blinks the amber LED to indicate data packet
1015  * activity, but we have no hardware support for that, so it would
1016  * require waking up every 10-20 msecs and checking the counters
1017  * on the chip, and then turning the LED off if appropriate.  That's
1018  * visible overhead, so not something we will do.
1019  *
1020  */
1021 static void ipath_setup_ht_setextled(struct ipath_devdata *dd,
1022                                      u64 lst, u64 ltst)
1023 {
1024         u64 extctl;
1025
1026         /* the diags use the LED to indicate diag info, so we leave
1027          * the external LED alone when the diags are running */
1028         if (ipath_diag_inuse)
1029                 return;
1030
1031         /*
1032          * start by setting both LED control bits to off, then turn
1033          * on the appropriate bit(s).
1034          */
1035         if (dd->ipath_boardrev == 8) { /* LS/X-1 uses different pins */
1036                 /*
1037                  * major difference is that INFINIPATH_EXTC_LEDGBLERR_OFF
1038                  * is inverted,  because it is normally used to indicate
1039                  * a hardware fault at reset, if there were errors
1040                  */
1041                 extctl = (dd->ipath_extctrl & ~INFINIPATH_EXTC_LEDGBLOK_ON)
1042                         | INFINIPATH_EXTC_LEDGBLERR_OFF;
1043                 if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP)
1044                         extctl &= ~INFINIPATH_EXTC_LEDGBLERR_OFF;
1045                 if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
1046                         extctl |= INFINIPATH_EXTC_LEDGBLOK_ON;
1047         }
1048         else {
1049                 extctl = dd->ipath_extctrl &
1050                         ~(INFINIPATH_EXTC_LED1PRIPORT_ON |
1051                           INFINIPATH_EXTC_LED2PRIPORT_ON);
1052                 if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP)
1053                         extctl |= INFINIPATH_EXTC_LED1PRIPORT_ON;
1054                 if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
1055                         extctl |= INFINIPATH_EXTC_LED2PRIPORT_ON;
1056         }
1057         dd->ipath_extctrl = extctl;
1058         ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, extctl);
1059 }
1060
1061 static void ipath_init_ht_variables(void)
1062 {
1063         ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM;
1064         ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM;
1065         ipath_gpio_sda = IPATH_GPIO_SDA;
1066         ipath_gpio_scl = IPATH_GPIO_SCL;
1067
1068         infinipath_i_bitsextant =
1069                 (INFINIPATH_I_RCVURG_MASK << INFINIPATH_I_RCVURG_SHIFT) |
1070                 (INFINIPATH_I_RCVAVAIL_MASK <<
1071                  INFINIPATH_I_RCVAVAIL_SHIFT) |
1072                 INFINIPATH_I_ERROR | INFINIPATH_I_SPIOSENT |
1073                 INFINIPATH_I_SPIOBUFAVAIL | INFINIPATH_I_GPIO;
1074
1075         infinipath_e_bitsextant =
1076                 INFINIPATH_E_RFORMATERR | INFINIPATH_E_RVCRC |
1077                 INFINIPATH_E_RICRC | INFINIPATH_E_RMINPKTLEN |
1078                 INFINIPATH_E_RMAXPKTLEN | INFINIPATH_E_RLONGPKTLEN |
1079                 INFINIPATH_E_RSHORTPKTLEN | INFINIPATH_E_RUNEXPCHAR |
1080                 INFINIPATH_E_RUNSUPVL | INFINIPATH_E_REBP |
1081                 INFINIPATH_E_RIBFLOW | INFINIPATH_E_RBADVERSION |
1082                 INFINIPATH_E_RRCVEGRFULL | INFINIPATH_E_RRCVHDRFULL |
1083                 INFINIPATH_E_RBADTID | INFINIPATH_E_RHDRLEN |
1084                 INFINIPATH_E_RHDR | INFINIPATH_E_RIBLOSTLINK |
1085                 INFINIPATH_E_SMINPKTLEN | INFINIPATH_E_SMAXPKTLEN |
1086                 INFINIPATH_E_SUNDERRUN | INFINIPATH_E_SPKTLEN |
1087                 INFINIPATH_E_SDROPPEDSMPPKT | INFINIPATH_E_SDROPPEDDATAPKT |
1088                 INFINIPATH_E_SPIOARMLAUNCH | INFINIPATH_E_SUNEXPERRPKTNUM |
1089                 INFINIPATH_E_SUNSUPVL | INFINIPATH_E_IBSTATUSCHANGED |
1090                 INFINIPATH_E_INVALIDADDR | INFINIPATH_E_RESET |
1091                 INFINIPATH_E_HARDWARE;
1092
1093         infinipath_hwe_bitsextant =
1094                 (INFINIPATH_HWE_HTCMEMPARITYERR_MASK <<
1095                  INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT) |
1096                 (INFINIPATH_HWE_TXEMEMPARITYERR_MASK <<
1097                  INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) |
1098                 (INFINIPATH_HWE_RXEMEMPARITYERR_MASK <<
1099                  INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) |
1100                 INFINIPATH_HWE_HTCLNKABYTE0CRCERR |
1101                 INFINIPATH_HWE_HTCLNKABYTE1CRCERR |
1102                 INFINIPATH_HWE_HTCLNKBBYTE0CRCERR |
1103                 INFINIPATH_HWE_HTCLNKBBYTE1CRCERR |
1104                 INFINIPATH_HWE_HTCMISCERR4 |
1105                 INFINIPATH_HWE_HTCMISCERR5 | INFINIPATH_HWE_HTCMISCERR6 |
1106                 INFINIPATH_HWE_HTCMISCERR7 |
1107                 INFINIPATH_HWE_HTCBUSTREQPARITYERR |
1108                 INFINIPATH_HWE_HTCBUSTRESPPARITYERR |
1109                 INFINIPATH_HWE_HTCBUSIREQPARITYERR |
1110                 INFINIPATH_HWE_RXDSYNCMEMPARITYERR |
1111                 INFINIPATH_HWE_MEMBISTFAILED |
1112                 INFINIPATH_HWE_COREPLL_FBSLIP |
1113                 INFINIPATH_HWE_COREPLL_RFSLIP |
1114                 INFINIPATH_HWE_HTBPLL_FBSLIP |
1115                 INFINIPATH_HWE_HTBPLL_RFSLIP |
1116                 INFINIPATH_HWE_HTAPLL_FBSLIP |
1117                 INFINIPATH_HWE_HTAPLL_RFSLIP |
1118                 INFINIPATH_HWE_SERDESPLLFAILED |
1119                 INFINIPATH_HWE_IBCBUSTOSPCPARITYERR |
1120                 INFINIPATH_HWE_IBCBUSFRSPCPARITYERR;
1121
1122         infinipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK;
1123         infinipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK;
1124 }
1125
1126 /**
1127  * ipath_ht_init_hwerrors - enable hardware errors
1128  * @dd: the infinipath device
1129  *
1130  * now that we have finished initializing everything that might reasonably
1131  * cause a hardware error, and cleared those errors bits as they occur,
1132  * we can enable hardware errors in the mask (potentially enabling
1133  * freeze mode), and enable hardware errors as errors (along with
1134  * everything else) in errormask
1135  */
1136 static void ipath_ht_init_hwerrors(struct ipath_devdata *dd)
1137 {
1138         ipath_err_t val;
1139         u64 extsval;
1140
1141         extsval = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
1142
1143         if (!(extsval & INFINIPATH_EXTS_MEMBIST_ENDTEST))
1144                 ipath_dev_err(dd, "MemBIST did not complete!\n");
1145
1146         ipath_check_htlink(dd);
1147
1148         /* barring bugs, all hwerrors become interrupts, which can */
1149         val = -1LL;
1150         /* don't look at crc lane1 if 8 bit */
1151         if (dd->ipath_flags & IPATH_8BIT_IN_HT0)
1152                 val &= ~infinipath_hwe_htclnkabyte1crcerr;
1153         /* don't look at crc lane1 if 8 bit */
1154         if (dd->ipath_flags & IPATH_8BIT_IN_HT1)
1155                 val &= ~infinipath_hwe_htclnkbbyte1crcerr;
1156
1157         /*
1158          * disable RXDSYNCMEMPARITY because external serdes is unused,
1159          * and therefore the logic will never be used or initialized,
1160          * and uninitialized state will normally result in this error
1161          * being asserted.  Similarly for the external serdess pll
1162          * lock signal.
1163          */
1164         val &= ~(INFINIPATH_HWE_SERDESPLLFAILED |
1165                  INFINIPATH_HWE_RXDSYNCMEMPARITYERR);
1166
1167         /*
1168          * Disable MISCERR4 because of an inversion in the HT core
1169          * logic checking for errors that cause this bit to be set.
1170          * The errata can also cause the protocol error bit to be set
1171          * in the HT config space linkerror register(s).
1172          */
1173         val &= ~INFINIPATH_HWE_HTCMISCERR4;
1174
1175         /*
1176          * PLL ignored because MDIO interface has a logic problem
1177          * for reads, on Comstock and Ponderosa.  BRINGUP
1178          */
1179         if (dd->ipath_boardrev == 4 || dd->ipath_boardrev == 9)
1180                 val &= ~INFINIPATH_HWE_SERDESPLLFAILED;
1181         dd->ipath_hwerrmask = val;
1182 }
1183
1184 /**
1185  * ipath_ht_bringup_serdes - bring up the serdes
1186  * @dd: the infinipath device
1187  */
1188 static int ipath_ht_bringup_serdes(struct ipath_devdata *dd)
1189 {
1190         u64 val, config1;
1191         int ret = 0, change = 0;
1192
1193         ipath_dbg("Trying to bringup serdes\n");
1194
1195         if (ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus) &
1196             INFINIPATH_HWE_SERDESPLLFAILED)
1197         {
1198                 ipath_dbg("At start, serdes PLL failed bit set in "
1199                           "hwerrstatus, clearing and continuing\n");
1200                 ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
1201                                  INFINIPATH_HWE_SERDESPLLFAILED);
1202         }
1203
1204         val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
1205         config1 = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig1);
1206
1207         ipath_cdbg(VERBOSE, "Initial serdes status is config0=%llx "
1208                    "config1=%llx, sstatus=%llx xgxs %llx\n",
1209                    (unsigned long long) val, (unsigned long long) config1,
1210                    (unsigned long long)
1211                    ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesstatus),
1212                    (unsigned long long)
1213                    ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
1214
1215         /* force reset on */
1216         val |= INFINIPATH_SERDC0_RESET_PLL
1217                 /* | INFINIPATH_SERDC0_RESET_MASK */
1218                 ;
1219         ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
1220         udelay(15);             /* need pll reset set at least for a bit */
1221
1222         if (val & INFINIPATH_SERDC0_RESET_PLL) {
1223                 u64 val2 = val &= ~INFINIPATH_SERDC0_RESET_PLL;
1224                 /* set lane resets, and tx idle, during pll reset */
1225                 val2 |= INFINIPATH_SERDC0_RESET_MASK |
1226                         INFINIPATH_SERDC0_TXIDLE;
1227                 ipath_cdbg(VERBOSE, "Clearing serdes PLL reset (writing "
1228                            "%llx)\n", (unsigned long long) val2);
1229                 ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0,
1230                                  val2);
1231                 /*
1232                  * be sure chip saw it
1233                  */
1234                 val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
1235                 /*
1236                  * need pll reset clear at least 11 usec before lane
1237                  * resets cleared; give it a few more
1238                  */
1239                 udelay(15);
1240                 val = val2;     /* for check below */
1241         }
1242
1243         if (val & (INFINIPATH_SERDC0_RESET_PLL |
1244                    INFINIPATH_SERDC0_RESET_MASK |
1245                    INFINIPATH_SERDC0_TXIDLE)) {
1246                 val &= ~(INFINIPATH_SERDC0_RESET_PLL |
1247                          INFINIPATH_SERDC0_RESET_MASK |
1248                          INFINIPATH_SERDC0_TXIDLE);
1249                 /* clear them */
1250                 ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0,
1251                                  val);
1252         }
1253
1254         val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
1255         if (((val >> INFINIPATH_XGXS_MDIOADDR_SHIFT) &
1256              INFINIPATH_XGXS_MDIOADDR_MASK) != 3) {
1257                 val &= ~(INFINIPATH_XGXS_MDIOADDR_MASK <<
1258                          INFINIPATH_XGXS_MDIOADDR_SHIFT);
1259                 /*
1260                  * we use address 3
1261                  */
1262                 val |= 3ULL << INFINIPATH_XGXS_MDIOADDR_SHIFT;
1263                 change = 1;
1264         }
1265         if (val & INFINIPATH_XGXS_RESET) {
1266                 /* normally true after boot */
1267                 val &= ~INFINIPATH_XGXS_RESET;
1268                 change = 1;
1269         }
1270         if (((val >> INFINIPATH_XGXS_RX_POL_SHIFT) &
1271              INFINIPATH_XGXS_RX_POL_MASK) != dd->ipath_rx_pol_inv ) {
1272                 /* need to compensate for Tx inversion in partner */
1273                 val &= ~(INFINIPATH_XGXS_RX_POL_MASK <<
1274                          INFINIPATH_XGXS_RX_POL_SHIFT);
1275                 val |= dd->ipath_rx_pol_inv <<
1276                         INFINIPATH_XGXS_RX_POL_SHIFT;
1277                 change = 1;
1278         }
1279         if (change)
1280                 ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
1281
1282         val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
1283
1284         /* clear current and de-emphasis bits */
1285         config1 &= ~0x0ffffffff00ULL;
1286         /* set current to 20ma */
1287         config1 |= 0x00000000000ULL;
1288         /* set de-emphasis to -5.68dB */
1289         config1 |= 0x0cccc000000ULL;
1290         ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig1, config1);
1291
1292         ipath_cdbg(VERBOSE, "After setup: serdes status is config0=%llx "
1293                    "config1=%llx, sstatus=%llx xgxs %llx\n",
1294                    (unsigned long long) val, (unsigned long long) config1,
1295                    (unsigned long long)
1296                    ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesstatus),
1297                    (unsigned long long)
1298                    ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
1299
1300         if (!ipath_waitfor_mdio_cmdready(dd)) {
1301                 ipath_write_kreg(dd, dd->ipath_kregs->kr_mdio,
1302                                  ipath_mdio_req(IPATH_MDIO_CMD_READ, 31,
1303                                                 IPATH_MDIO_CTRL_XGXS_REG_8,
1304                                                 0));
1305                 if (ipath_waitfor_complete(dd, dd->ipath_kregs->kr_mdio,
1306                                            IPATH_MDIO_DATAVALID, &val))
1307                         ipath_dbg("Never got MDIO data for XGXS status "
1308                                   "read\n");
1309                 else
1310                         ipath_cdbg(VERBOSE, "MDIO Read reg8, "
1311                                    "'bank' 31 %x\n", (u32) val);
1312         } else
1313                 ipath_dbg("Never got MDIO cmdready for XGXS status read\n");
1314
1315         return ret;             /* for now, say we always succeeded */
1316 }
1317
1318 /**
1319  * ipath_ht_quiet_serdes - set serdes to txidle
1320  * @dd: the infinipath device
1321  * driver is being unloaded
1322  */
1323 static void ipath_ht_quiet_serdes(struct ipath_devdata *dd)
1324 {
1325         u64 val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
1326
1327         val |= INFINIPATH_SERDC0_TXIDLE;
1328         ipath_dbg("Setting TxIdleEn on serdes (config0 = %llx)\n",
1329                   (unsigned long long) val);
1330         ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
1331 }
1332
1333 static int ipath_ht_intconfig(struct ipath_devdata *dd)
1334 {
1335         int ret;
1336
1337         if (!dd->ipath_intconfig) {
1338                 ipath_dev_err(dd, "No interrupts enabled, couldn't setup "
1339                               "interrupt address\n");
1340                 ret = 1;
1341                 goto bail;
1342         }
1343
1344         ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig,
1345                          dd->ipath_intconfig);  /* interrupt address */
1346         ret = 0;
1347
1348 bail:
1349         return ret;
1350 }
1351
1352 /**
1353  * ipath_pe_put_tid - write a TID in chip
1354  * @dd: the infinipath device
1355  * @tidptr: pointer to the expected TID (in chip) to udpate
1356  * @tidtype: 0 for eager, 1 for expected
1357  * @pa: physical address of in memory buffer; ipath_tidinvalid if freeing
1358  *
1359  * This exists as a separate routine to allow for special locking etc.
1360  * It's used for both the full cleanup on exit, as well as the normal
1361  * setup and teardown.
1362  */
1363 static void ipath_ht_put_tid(struct ipath_devdata *dd,
1364                              u64 __iomem *tidptr, u32 type,
1365                              unsigned long pa)
1366 {
1367         if (pa != dd->ipath_tidinvalid) {
1368                 if (unlikely((pa & ~INFINIPATH_RT_ADDR_MASK))) {
1369                         dev_info(&dd->pcidev->dev,
1370                                  "physaddr %lx has more than "
1371                                  "40 bits, using only 40!!!\n", pa);
1372                         pa &= INFINIPATH_RT_ADDR_MASK;
1373                 }
1374                 if (type == 0)
1375                         pa |= dd->ipath_tidtemplate;
1376                 else {
1377                         /* in words (fixed, full page).  */
1378                         u64 lenvalid = PAGE_SIZE >> 2;
1379                         lenvalid <<= INFINIPATH_RT_BUFSIZE_SHIFT;
1380                         pa |= lenvalid | INFINIPATH_RT_VALID;
1381                 }
1382         }
1383         if (dd->ipath_kregbase)
1384                 writeq(pa, tidptr);
1385 }
1386
1387 /**
1388  * ipath_ht_clear_tid - clear all TID entries for a port, expected and eager
1389  * @dd: the infinipath device
1390  * @port: the port
1391  *
1392  * Used from ipath_close(), and at chip initialization.
1393  */
1394 static void ipath_ht_clear_tids(struct ipath_devdata *dd, unsigned port)
1395 {
1396         u64 __iomem *tidbase;
1397         int i;
1398
1399         if (!dd->ipath_kregbase)
1400                 return;
1401
1402         ipath_cdbg(VERBOSE, "Invalidate TIDs for port %u\n", port);
1403
1404         /*
1405          * need to invalidate all of the expected TID entries for this
1406          * port, so we don't have valid entries that might somehow get
1407          * used (early in next use of this port, or through some bug)
1408          */
1409         tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) +
1410                                    dd->ipath_rcvtidbase +
1411                                    port * dd->ipath_rcvtidcnt *
1412                                    sizeof(*tidbase));
1413         for (i = 0; i < dd->ipath_rcvtidcnt; i++)
1414                 ipath_ht_put_tid(dd, &tidbase[i], 1, dd->ipath_tidinvalid);
1415
1416         tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) +
1417                                    dd->ipath_rcvegrbase +
1418                                    port * dd->ipath_rcvegrcnt *
1419                                    sizeof(*tidbase));
1420
1421         for (i = 0; i < dd->ipath_rcvegrcnt; i++)
1422                 ipath_ht_put_tid(dd, &tidbase[i], 0, dd->ipath_tidinvalid);
1423 }
1424
1425 /**
1426  * ipath_ht_tidtemplate - setup constants for TID updates
1427  * @dd: the infinipath device
1428  *
1429  * We setup stuff that we use a lot, to avoid calculating each time
1430  */
1431 static void ipath_ht_tidtemplate(struct ipath_devdata *dd)
1432 {
1433         dd->ipath_tidtemplate = dd->ipath_ibmaxlen >> 2;
1434         dd->ipath_tidtemplate <<= INFINIPATH_RT_BUFSIZE_SHIFT;
1435         dd->ipath_tidtemplate |= INFINIPATH_RT_VALID;
1436
1437         /*
1438          * work around chip errata bug 7358, by marking invalid tids
1439          * as having max length
1440          */
1441         dd->ipath_tidinvalid = (-1LL & INFINIPATH_RT_BUFSIZE_MASK) <<
1442                 INFINIPATH_RT_BUFSIZE_SHIFT;
1443 }
1444
1445 static int ipath_ht_early_init(struct ipath_devdata *dd)
1446 {
1447         u32 __iomem *piobuf;
1448         u32 pioincr, val32, egrsize;
1449         int i;
1450
1451         /*
1452          * one cache line; long IB headers will spill over into received
1453          * buffer
1454          */
1455         dd->ipath_rcvhdrentsize = 16;
1456         dd->ipath_rcvhdrsize = IPATH_DFLT_RCVHDRSIZE;
1457
1458         /*
1459          * For HT, we allocate a somewhat overly large eager buffer,
1460          * such that we can guarantee that we can receive the largest
1461          * packet that we can send out.  To truly support a 4KB MTU,
1462          * we need to bump this to a large value.  To date, other than
1463          * testing, we have never encountered an HCA that can really
1464          * send 4KB MTU packets, so we do not handle that (we'll get
1465          * errors interrupts if we ever see one).
1466          */
1467         dd->ipath_rcvegrbufsize = dd->ipath_piosize2k;
1468         egrsize = dd->ipath_rcvegrbufsize;
1469
1470         /*
1471          * the min() check here is currently a nop, but it may not
1472          * always be, depending on just how we do ipath_rcvegrbufsize
1473          */
1474         dd->ipath_ibmaxlen = min(dd->ipath_piosize2k,
1475                                  dd->ipath_rcvegrbufsize);
1476         dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen;
1477         ipath_ht_tidtemplate(dd);
1478
1479         /*
1480          * zero all the TID entries at startup.  We do this for sanity,
1481          * in case of a previous driver crash of some kind, and also
1482          * because the chip powers up with these memories in an unknown
1483          * state.  Use portcnt, not cfgports, since this is for the
1484          * full chip, not for current (possibly different) configuration
1485          * value.
1486          * Chip Errata bug 6447
1487          */
1488         for (val32 = 0; val32 < dd->ipath_portcnt; val32++)
1489                 ipath_ht_clear_tids(dd, val32);
1490
1491         /*
1492          * write the pbc of each buffer, to be sure it's initialized, then
1493          * cancel all the buffers, and also abort any packets that might
1494          * have been in flight for some reason (the latter is for driver
1495          * unload/reload, but isn't a bad idea at first init).  PIO send
1496          * isn't enabled at this point, so there is no danger of sending
1497          * these out on the wire.
1498          * Chip Errata bug 6610
1499          */
1500         piobuf = (u32 __iomem *) (((char __iomem *)(dd->ipath_kregbase)) +
1501                                   dd->ipath_piobufbase);
1502         pioincr = dd->ipath_palign / sizeof(*piobuf);
1503         for (i = 0; i < dd->ipath_piobcnt2k; i++) {
1504                 /*
1505                  * reasonable word count, just to init pbc
1506                  */
1507                 writel(16, piobuf);
1508                 piobuf += pioincr;
1509         }
1510         /*
1511          * self-clearing
1512          */
1513         ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
1514                          INFINIPATH_S_ABORT);
1515
1516         ipath_get_eeprom_info(dd);
1517         if(dd->ipath_boardrev == 5 && dd->ipath_serial[0] == '1' &&
1518                 dd->ipath_serial[1] == '2' && dd->ipath_serial[2] == '8') {
1519                 /*
1520                  * Later production QHT7040 has same changes as QHT7140, so
1521                  * can use GPIO interrupts.  They have serial #'s starting
1522                  * with 128, rather than 112.
1523                  */
1524                 dd->ipath_flags |= IPATH_GPIO_INTR;
1525                 dd->ipath_flags &= ~IPATH_POLL_RX_INTR;
1526         }
1527         return 0;
1528 }
1529
1530 /**
1531  * ipath_init_ht_get_base_info - set chip-specific flags for user code
1532  * @dd: the infinipath device
1533  * @kbase: ipath_base_info pointer
1534  *
1535  * We set the PCIE flag because the lower bandwidth on PCIe vs
1536  * HyperTransport can affect some user packet algorithims.
1537  */
1538 static int ipath_ht_get_base_info(struct ipath_portdata *pd, void *kbase)
1539 {
1540         struct ipath_base_info *kinfo = kbase;
1541
1542         kinfo->spi_runtime_flags |= IPATH_RUNTIME_HT |
1543                 IPATH_RUNTIME_RCVHDR_COPY;
1544
1545         return 0;
1546 }
1547
1548 /**
1549  * ipath_init_iba6110_funcs - set up the chip-specific function pointers
1550  * @dd: the infinipath device
1551  *
1552  * This is global, and is called directly at init to set up the
1553  * chip-specific function pointers for later use.
1554  */
1555 void ipath_init_iba6110_funcs(struct ipath_devdata *dd)
1556 {
1557         dd->ipath_f_intrsetup = ipath_ht_intconfig;
1558         dd->ipath_f_bus = ipath_setup_ht_config;
1559         dd->ipath_f_reset = ipath_setup_ht_reset;
1560         dd->ipath_f_get_boardname = ipath_ht_boardname;
1561         dd->ipath_f_init_hwerrors = ipath_ht_init_hwerrors;
1562         dd->ipath_f_early_init = ipath_ht_early_init;
1563         dd->ipath_f_handle_hwerrors = ipath_ht_handle_hwerrors;
1564         dd->ipath_f_quiet_serdes = ipath_ht_quiet_serdes;
1565         dd->ipath_f_bringup_serdes = ipath_ht_bringup_serdes;
1566         dd->ipath_f_clear_tids = ipath_ht_clear_tids;
1567         dd->ipath_f_put_tid = ipath_ht_put_tid;
1568         dd->ipath_f_cleanup = ipath_setup_ht_cleanup;
1569         dd->ipath_f_setextled = ipath_setup_ht_setextled;
1570         dd->ipath_f_get_base_info = ipath_ht_get_base_info;
1571
1572         /*
1573          * initialize chip-specific variables
1574          */
1575         dd->ipath_f_tidtemplate = ipath_ht_tidtemplate;
1576
1577         /*
1578          * setup the register offsets, since they are different for each
1579          * chip
1580          */
1581         dd->ipath_kregs = &ipath_ht_kregs;
1582         dd->ipath_cregs = &ipath_ht_cregs;
1583
1584         /*
1585          * do very early init that is needed before ipath_f_bus is
1586          * called
1587          */
1588         ipath_init_ht_variables();
1589 }