5 menu "Graphics support"
7 source "drivers/video/backlight/Kconfig"
8 source "drivers/video/display/Kconfig"
15 tristate "Support for frame buffer devices"
17 The frame buffer device provides an abstraction for the graphics
18 hardware. It represents the frame buffer of some video hardware and
19 allows application software to access the graphics hardware through
20 a well-defined interface, so the software doesn't need to know
21 anything about the low-level (hardware register) stuff.
23 Frame buffer devices work identically across the different
24 architectures supported by Linux and make the implementation of
25 application programs easier and more portable; at this point, an X
26 server exists which uses the frame buffer device exclusively.
27 On several non-X86 architectures, the frame buffer device is the
28 only way to use the graphics hardware.
30 The device is accessed through special device nodes, usually located
31 in the /dev directory, i.e. /dev/fb*.
33 You need an utility program called fbset to make full use of frame
34 buffer devices. Please read <file:Documentation/fb/framebuffer.txt>
35 and the Framebuffer-HOWTO at
36 <http://www.tahallah.demon.co.uk/programming/prog.html> for more
39 Say Y here and to the driver for your graphics board below if you
40 are compiling a kernel for a non-x86 architecture.
42 If you are compiling for the x86 architecture, you can say Y if you
43 want to play with it, but it is not essential. Please note that
44 running graphical applications that directly touch the hardware
45 (e.g. an accelerated X server) and that are not frame buffer
46 device-aware may cause unexpected results. If unsure, say N.
49 bool "Enable firmware EDID"
53 This enables access to the EDID transferred from the firmware.
54 On the i386, this is from the Video BIOS. Enable this if DDC/I2C
55 transfers do not work for your driver and if you are using
56 nvidiafb, i810fb or savagefb.
58 In general, choosing Y for this option is safe. If you
59 experience extremely long delays while booting before you get
60 something on your display, try setting this to N. Matrox cards in
61 combination with certain motherboards and monitors are known to
62 suffer from this problem.
71 config FB_CFB_FILLRECT
76 Include the cfb_fillrect function for generic software rectangle
77 filling. This is used by drivers that don't provide their own
78 (accelerated) version.
80 config FB_CFB_COPYAREA
85 Include the cfb_copyarea function for generic software area copying.
86 This is used by drivers that don't provide their own (accelerated)
89 config FB_CFB_IMAGEBLIT
94 Include the cfb_imageblit function for generic software image
95 blitting. This is used by drivers that don't provide their own
96 (accelerated) version.
98 config FB_SYS_FILLRECT
103 Include the sys_fillrect function for generic software rectangle
104 filling. This is used by drivers that don't provide their own
105 (accelerated) version and the framebuffer is in system RAM.
107 config FB_SYS_COPYAREA
112 Include the sys_copyarea function for generic software area copying.
113 This is used by drivers that don't provide their own (accelerated)
114 version and the framebuffer is in system RAM.
116 config FB_SYS_IMAGEBLIT
121 Include the sys_imageblit function for generic software image
122 blitting. This is used by drivers that don't provide their own
123 (accelerated) version and the framebuffer is in system RAM.
130 config FB_DEFERRED_IO
140 Common utility functions useful to fbdev drivers of VGA-based
151 select BACKLIGHT_LCD_SUPPORT
152 select BACKLIGHT_CLASS_DEVICE
155 config FB_MODE_HELPERS
156 bool "Enable Video Mode Handling Helpers"
160 This enables functions for handling video modes using the
161 Generalized Timing Formula and the EDID parser. A few drivers rely
162 on this feature such as the radeonfb, rivafb, and the i810fb. If
163 your driver does not take advantage of this feature, choosing Y will
164 just increase the kernel size by about 5K.
166 config FB_TILEBLITTING
167 bool "Enable Tile Blitting Support"
171 This enables tile blitting. Tile blitting is a drawing technique
172 where the screen is divided into rectangular sections (tiles), whereas
173 the standard blitting divides the screen into pixels. Because the
174 default drawing element is a tile, drawing functions will be passed
175 parameters in terms of number of tiles instead of number of pixels.
176 For example, to draw a single character, instead of using bitmaps,
177 an index to an array of bitmaps will be used. To clear or move a
178 rectangular section of a screen, the rectangle will be described in
179 terms of number of tiles in the x- and y-axis.
181 This is particularly important to one driver, matroxfb. If
184 comment "Frame buffer hardware drivers"
188 tristate "Cirrus Logic support"
189 depends on FB && (ZORRO || PCI)
190 select FB_CFB_FILLRECT
191 select FB_CFB_COPYAREA
192 select FB_CFB_IMAGEBLIT
194 This enables support for Cirrus Logic GD542x/543x based boards on
195 Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum.
197 If you have a PCI-based system, this enables support for these
198 chips: GD-543x, GD-544x, GD-5480.
200 Please read the file <file:Documentation/fb/cirrusfb.txt>.
202 Say N unless you have such a graphics board or plan to get one
203 before you next recompile the kernel.
206 tristate "Permedia2 support"
207 depends on FB && ((AMIGA && BROKEN) || PCI)
208 select FB_CFB_FILLRECT
209 select FB_CFB_COPYAREA
210 select FB_CFB_IMAGEBLIT
212 This is the frame buffer device driver for the Permedia2 AGP frame
213 buffer card from ASK, aka `Graphic Blaster Exxtreme'. There is a
215 <http://www.ask.com.hk/product/Permedia%202/permedia2.htm>.
217 config FB_PM2_FIFO_DISCONNECT
218 bool "enable FIFO disconnect feature"
219 depends on FB_PM2 && PCI
221 Support the Permedia2 FIFO disconnect feature (see CONFIG_FB_PM2).
224 tristate "ARM PrimeCell PL110 support"
225 depends on FB && ARM && ARM_AMBA
226 select FB_CFB_FILLRECT
227 select FB_CFB_COPYAREA
228 select FB_CFB_IMAGEBLIT
230 This framebuffer device driver is for the ARM PrimeCell PL110
231 Colour LCD controller. ARM PrimeCells provide the building
232 blocks for System on a Chip devices.
234 If you want to compile this as a module (=code which can be
235 inserted into and removed from the running kernel), say M
236 here and read <file:Documentation/kbuild/modules.txt>. The module
237 will be called amba-clcd.
241 depends on FB_ARMCLCD && (ARCH_LH7A40X || ARCH_LH7952X)
243 default FB_ARMCLCD_SHARP_LQ035Q7DB02
245 config FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
246 bool "LogicPD LCD 3.5\" QVGA w/HRTFT IC"
248 This is an implementation of the Sharp LQ035Q7DB02, a 3.5"
249 color QVGA, HRTFT panel. The LogicPD device includes
250 an integrated HRTFT controller IC.
251 The native resolution is 240x320.
253 config FB_ARMCLCD_SHARP_LQ057Q3DC02
254 bool "LogicPD LCD 5.7\" QVGA"
256 This is an implementation of the Sharp LQ057Q3DC02, a 5.7"
257 color QVGA, TFT panel. The LogicPD device includes an
258 The native resolution is 320x240.
260 config FB_ARMCLCD_SHARP_LQ64D343
261 bool "LogicPD LCD 6.4\" VGA"
263 This is an implementation of the Sharp LQ64D343, a 6.4"
264 color VGA, TFT panel. The LogicPD device includes an
265 The native resolution is 640x480.
267 config FB_ARMCLCD_SHARP_LQ10D368
268 bool "LogicPD LCD 10.4\" VGA"
270 This is an implementation of the Sharp LQ10D368, a 10.4"
271 color VGA, TFT panel. The LogicPD device includes an
272 The native resolution is 640x480.
275 config FB_ARMCLCD_SHARP_LQ121S1DG41
276 bool "LogicPD LCD 12.1\" SVGA"
278 This is an implementation of the Sharp LQ121S1DG41, a 12.1"
279 color SVGA, TFT panel. The LogicPD device includes an
280 The native resolution is 800x600.
282 This panel requires a clock rate may be an integer fraction
283 of the base LCDCLK frequency. The driver will select the
284 highest frequency available that is lower than the maximum
285 allowed. The panel may flicker if the clock rate is
286 slower than the recommended minimum.
288 config FB_ARMCLCD_AUO_A070VW01_WIDE
289 bool "AU Optronics A070VW01 LCD 7.0\" WIDE"
291 This is an implementation of the AU Optronics, a 7.0"
292 WIDE Color. The native resolution is 234x480.
294 config FB_ARMCLCD_HITACHI
295 bool "Hitachi Wide Screen 800x480"
297 This is an implementation of the Hitachi 800x480.
303 bool "Acorn VIDC support"
304 depends on (FB = y) && ARM && (ARCH_ACORN || ARCH_CLPS7500)
305 select FB_CFB_FILLRECT
306 select FB_CFB_COPYAREA
307 select FB_CFB_IMAGEBLIT
309 This is the frame buffer device driver for the Acorn VIDC graphics
310 hardware found in Acorn RISC PCs and other ARM-based machines. If
314 bool "CLPS711X LCD support"
315 depends on (FB = y) && ARM && ARCH_CLPS711X
316 select FB_CFB_FILLRECT
317 select FB_CFB_COPYAREA
318 select FB_CFB_IMAGEBLIT
320 Say Y to enable the Framebuffer driver for the CLPS7111 and
324 bool "SA-1100 LCD support"
325 depends on (FB = y) && ARM && ARCH_SA1100
326 select FB_CFB_FILLRECT
327 select FB_CFB_COPYAREA
328 select FB_CFB_IMAGEBLIT
330 This is a framebuffer device for the SA-1100 LCD Controller.
331 See <http://www.linux-fbdev.org/> for information on framebuffer
334 If you plan to use the LCD display with your SA-1100 system, say
338 tristate "Motorola i.MX LCD support"
339 depends on FB && ARM && ARCH_IMX
340 select FB_CFB_FILLRECT
341 select FB_CFB_COPYAREA
342 select FB_CFB_IMAGEBLIT
345 tristate "CyberPro 2000/2010/5000 support"
346 depends on FB && PCI && (BROKEN || !SPARC64)
347 select FB_CFB_FILLRECT
348 select FB_CFB_COPYAREA
349 select FB_CFB_IMAGEBLIT
351 This enables support for the Integraphics CyberPro 20x0 and 5000
352 VGA chips used in the Rebel.com Netwinder and other machines.
353 Say Y if you have a NetWinder or a graphics card containing this
354 device, otherwise say N.
358 depends on (FB = y) && APOLLO
360 select FB_CFB_FILLRECT
361 select FB_CFB_IMAGEBLIT
365 depends on (FB = y) && Q40
367 select FB_CFB_FILLRECT
368 select FB_CFB_COPYAREA
369 select FB_CFB_IMAGEBLIT
372 tristate "Amiga native chipset support"
373 depends on FB && AMIGA
375 This is the frame buffer device driver for the builtin graphics
376 chipset found in Amigas.
378 To compile this driver as a module, choose M here: the
379 module will be called amifb.
382 bool "Amiga OCS chipset support"
385 This enables support for the original Agnus and Denise video chips,
386 found in the Amiga 1000 and most A500's and A2000's. If you intend
387 to run Linux on any of these systems, say Y; otherwise say N.
390 bool "Amiga ECS chipset support"
393 This enables support for the Enhanced Chip Set, found in later
394 A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If
395 you intend to run Linux on any of these systems, say Y; otherwise
399 bool "Amiga AGA chipset support"
402 This enables support for the Advanced Graphics Architecture (also
403 known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T
404 and CD32. If you intend to run Linux on any of these systems, say Y;
408 bool "Amiga FrameMaster II/Rainbow II support"
409 depends on (FB = y) && ZORRO
410 select FB_CFB_FILLRECT
411 select FB_CFB_COPYAREA
412 select FB_CFB_IMAGEBLIT
414 This is the frame buffer device driver for the Amiga FrameMaster
415 card from BSC (exhibited 1992 but not shipped as a CBM product).
418 tristate "Arc Monochrome LCD board support"
420 select FB_SYS_FILLRECT
421 select FB_SYS_COPYAREA
422 select FB_SYS_IMAGEBLIT
425 This enables support for the Arc Monochrome LCD board. The board
426 is based on the KS-108 lcd controller and is typically a matrix
427 of 2*n chips. This driver was tested with a 128x64 panel. This
428 driver supports it for use with x86 SBCs through a 16 bit GPIO
429 interface (8 bit data, 8 bit control). If you anticipate using
430 this driver, say Y or M; otherwise say N. You must specify the
431 GPIO IO address to be used for setting control and data.
434 bool "Atari native chipset support"
435 depends on (FB = y) && ATARI
436 select FB_CFB_FILLRECT
437 select FB_CFB_COPYAREA
438 select FB_CFB_IMAGEBLIT
440 This is the frame buffer device driver for the builtin graphics
441 chipset found in Ataris.
444 bool "Open Firmware frame buffer device support"
445 depends on (FB = y) && (PPC64 || PPC_OF) && (!PPC_PSERIES || PCI)
446 select FB_CFB_FILLRECT
447 select FB_CFB_COPYAREA
448 select FB_CFB_IMAGEBLIT
451 Say Y if you want support with Open Firmware for your graphics
455 bool "Apple \"control\" display support"
456 depends on (FB = y) && PPC_PMAC && PPC32
457 select FB_CFB_FILLRECT
458 select FB_CFB_COPYAREA
459 select FB_CFB_IMAGEBLIT
462 This driver supports a frame buffer for the graphics adapter in the
463 Power Macintosh 7300 and others.
466 bool "Apple \"platinum\" display support"
467 depends on (FB = y) && PPC_PMAC && PPC32
468 select FB_CFB_FILLRECT
469 select FB_CFB_COPYAREA
470 select FB_CFB_IMAGEBLIT
473 This driver supports a frame buffer for the "platinum" graphics
474 adapter in some Power Macintoshes.
477 bool "Apple \"valkyrie\" display support"
478 depends on (FB = y) && (MAC || (PPC_PMAC && PPC32))
479 select FB_CFB_FILLRECT
480 select FB_CFB_COPYAREA
481 select FB_CFB_IMAGEBLIT
484 This driver supports a frame buffer for the "valkyrie" graphics
485 adapter in some Power Macintoshes.
488 bool "Chips 65550 display support"
489 depends on (FB = y) && PPC32
490 select FB_CFB_FILLRECT
491 select FB_CFB_COPYAREA
492 select FB_CFB_IMAGEBLIT
494 This is the frame buffer device driver for the Chips & Technologies
495 65550 graphics chip in PowerBooks.
498 bool "Asiliant (Chips) 69000 display support"
499 depends on (FB = y) && PCI
500 select FB_CFB_FILLRECT
501 select FB_CFB_COPYAREA
502 select FB_CFB_IMAGEBLIT
504 This is the frame buffer device driver for the Asiliant 69030 chipset
507 bool "IMS Twin Turbo display support"
508 depends on (FB = y) && PCI
509 select FB_CFB_IMAGEBLIT
510 select FB_MACMODES if PPC
512 The IMS Twin Turbo is a PCI-based frame buffer card bundled with
513 many Macintosh and compatible computers.
516 tristate "VGA 16-color graphics support"
517 depends on FB && (X86 || PPC)
518 select FB_CFB_FILLRECT
519 select FB_CFB_COPYAREA
520 select FB_CFB_IMAGEBLIT
522 select FONT_8x16 if FRAMEBUFFER_CONSOLE
524 This is the frame buffer device driver for VGA 16 color graphic
525 cards. Say Y if you have such a card.
527 To compile this driver as a module, choose M here: the
528 module will be called vga16fb.
531 tristate "HP STI frame buffer device support"
532 depends on FB && PARISC
533 select FB_CFB_FILLRECT
534 select FB_CFB_COPYAREA
535 select FB_CFB_IMAGEBLIT
538 STI refers to the HP "Standard Text Interface" which is a set of
539 BIOS routines contained in a ROM chip in HP PA-RISC based machines.
540 Enabling this option will implement the linux framebuffer device
541 using calls to the STI BIOS routines for initialisation.
543 If you enable this option, you will get a planar framebuffer device
544 /dev/fb which will work on the most common HP graphic cards of the
545 NGLE family, including the artist chips (in the 7xx and Bxxx series),
546 HCRX, HCRX24, CRX, CRX24 and VisEG series.
548 It is safe to enable this option, so you should probably say "Y".
551 bool "Generic Macintosh display support"
552 depends on (FB = y) && MAC
553 select FB_CFB_FILLRECT
554 select FB_CFB_COPYAREA
555 select FB_CFB_IMAGEBLIT
558 # bool ' Apple DAFB display support' CONFIG_FB_DAFB
561 depends on (FB = y) && HP300
562 select FB_CFB_FILLRECT
563 select FB_CFB_IMAGEBLIT
567 tristate "TGA/SFB+ framebuffer support"
568 depends on FB && (ALPHA || TC)
569 select FB_CFB_FILLRECT
570 select FB_CFB_COPYAREA
571 select FB_CFB_IMAGEBLIT
574 This is the frame buffer device driver for generic TGA and SFB+
575 graphic cards. These include DEC ZLXp-E1, -E2 and -E3 PCI cards,
576 also known as PBXGA-A, -B and -C, and DEC ZLX-E1, -E2 and -E3
577 TURBOchannel cards, also known as PMAGD-A, -B and -C.
579 Due to hardware limitations ZLX-E2 and E3 cards are not supported
580 for DECstation 5000/200 systems. Additionally due to firmware
581 limitations these cards may cause troubles with booting DECstation
582 5000/240 and /260 systems, but are fully supported under Linux if
583 you manage to get it going. ;-)
585 Say Y if you have one of those.
588 bool "VESA VGA graphics support"
589 depends on (FB = y) && X86
590 select FB_CFB_FILLRECT
591 select FB_CFB_COPYAREA
592 select FB_CFB_IMAGEBLIT
595 This is the frame buffer device driver for generic VESA 2.0
596 compliant graphic cards. The older VESA 1.2 cards are not supported.
597 You will get a boot time penguin logo at no additional cost. Please
598 read <file:Documentation/fb/vesafb.txt>. If unsure, say Y.
601 bool "Intel-based Macintosh Framebuffer Support"
602 depends on (FB = y) && X86 && EFI
603 select FB_CFB_FILLRECT
604 select FB_CFB_COPYAREA
605 select FB_CFB_IMAGEBLIT
607 This is the frame buffer device driver for the Intel-based Macintosh
610 tristate "Hecuba board support"
611 depends on FB && X86 && MMU
612 select FB_SYS_FILLRECT
613 select FB_SYS_COPYAREA
614 select FB_SYS_IMAGEBLIT
616 select FB_DEFERRED_IO
618 This enables support for the Hecuba board. This driver was tested
619 with an E-Ink 800x600 display and x86 SBCs through a 16 bit GPIO
620 interface (8 bit data, 4 bit control). If you anticpate using
621 this driver, say Y or M; otherwise say N. You must specify the
622 GPIO IO address to be used for setting control and data.
625 tristate "Hercules mono graphics support"
627 select FB_CFB_FILLRECT
628 select FB_CFB_COPYAREA
629 select FB_CFB_IMAGEBLIT
631 Say Y here if you have a Hercules mono graphics card.
633 To compile this driver as a module, choose M here: the
634 module will be called hgafb.
636 As this card technology is 15 years old, most people will answer N
640 bool "Hercules mono Acceleration functions (EXPERIMENTAL)"
641 depends on FB_HGA && EXPERIMENTAL
643 This will compile the Hercules mono graphics with
644 acceleration functions.
647 tristate "SGI Visual Workstation framebuffer support"
648 depends on FB && X86_VISWS
649 select FB_CFB_FILLRECT
650 select FB_CFB_COPYAREA
651 select FB_CFB_IMAGEBLIT
653 SGI Visual Workstation support for framebuffer graphics.
656 bool "SGI Graphics Backend frame buffer support"
657 depends on (FB = y) && (SGI_IP32 || X86_VISWS)
658 select FB_CFB_FILLRECT
659 select FB_CFB_COPYAREA
660 select FB_CFB_IMAGEBLIT
662 This is the frame buffer device driver for SGI Graphics Backend.
663 This chip is used in SGI O2 and Visual Workstation 320/540.
666 int "Video memory size in MB"
670 This is the amount of memory reserved for the framebuffer,
671 which can be any value between 1MB and 8MB.
674 bool "SBUS and UPA framebuffers"
675 depends on (FB = y) && SPARC
677 Say Y if you want support for SBUS or UPA based frame buffer device.
681 depends on (FB = y) && (SPARC && FB_SBUS)
682 select FB_CFB_FILLRECT
683 select FB_CFB_COPYAREA
684 select FB_CFB_IMAGEBLIT
686 This is the frame buffer device driver for the BWtwo frame buffer.
689 bool "CGthree support"
690 depends on (FB = y) && (SPARC && FB_SBUS)
691 select FB_CFB_FILLRECT
692 select FB_CFB_COPYAREA
693 select FB_CFB_IMAGEBLIT
695 This is the frame buffer device driver for the CGthree frame buffer.
698 bool "CGsix (GX,TurboGX) support"
699 depends on (FB = y) && (SPARC && FB_SBUS)
700 select FB_CFB_COPYAREA
701 select FB_CFB_IMAGEBLIT
703 This is the frame buffer device driver for the CGsix (GX, TurboGX)
707 tristate "NEC PowerVR 2 display support"
708 depends on FB && SH_DREAMCAST
709 select FB_CFB_FILLRECT
710 select FB_CFB_COPYAREA
711 select FB_CFB_IMAGEBLIT
713 Say Y here if you have a PowerVR 2 card in your box. If you plan to
714 run linux on your Dreamcast, you will have to say Y here.
715 This driver may or may not work on other PowerVR 2 cards, but is
716 totally untested. Use at your own risk. If unsure, say N.
718 To compile this driver as a module, choose M here: the
719 module will be called pvr2fb.
721 You can pass several parameters to the driver at boot time or at
722 module load time. The parameters look like "video=pvr2:XXX", where
723 the meaning of XXX can be found at the end of the main source file
724 (<file:drivers/video/pvr2fb.c>). Please see the file
725 <file:Documentation/fb/pvr2fb.txt>.
728 bool "Epson 1355 framebuffer support"
729 depends on (FB = y) && (SUPERH || ARCH_CEIVA)
730 select FB_CFB_FILLRECT
731 select FB_CFB_COPYAREA
732 select FB_CFB_IMAGEBLIT
734 Build in support for the SED1355 Epson Research Embedded RAMDAC
735 LCD/CRT Controller (since redesignated as the S1D13505) as a
736 framebuffer. Product specs at
737 <http://www.erd.epson.com/vdc/html/products.htm>.
740 tristate "Epson S1D13XXX framebuffer support"
742 select FB_CFB_FILLRECT
743 select FB_CFB_COPYAREA
744 select FB_CFB_IMAGEBLIT
746 Support for S1D13XXX framebuffer device family (currently only
747 working with S1D13806). Product specs at
748 <http://www.erd.epson.com/vdc/html/legacy_13xxx.htm>
751 tristate "nVidia Framebuffer Support"
753 select FB_BACKLIGHT if FB_NVIDIA_BACKLIGHT
754 select FB_MODE_HELPERS
755 select FB_CFB_FILLRECT
756 select FB_CFB_COPYAREA
757 select FB_CFB_IMAGEBLIT
761 This driver supports graphics boards with the nVidia chips, TNT
762 and newer. For very old chipsets, such as the RIVA128, then use
764 Say Y if you have such a graphics board.
766 To compile this driver as a module, choose M here: the
767 module will be called nvidiafb.
770 bool "Enable DDC Support"
774 This enables I2C support for nVidia Chipsets. This is used
775 only for getting EDID information from the attached display
776 allowing for robust video mode handling and switching.
778 Because fbdev-2.6 requires that drivers must be able to
779 independently validate video mode parameters, you should say Y
782 config FB_NVIDIA_BACKLIGHT
783 bool "Support for backlight control"
787 Say Y here if you want to control the backlight of your display.
790 tristate "nVidia Riva support"
792 select FB_BACKLIGHT if FB_RIVA_BACKLIGHT
793 select FB_MODE_HELPERS
794 select FB_CFB_FILLRECT
795 select FB_CFB_COPYAREA
796 select FB_CFB_IMAGEBLIT
800 This driver supports graphics boards with the nVidia Riva/Geforce
802 Say Y if you have such a graphics board.
804 To compile this driver as a module, choose M here: the
805 module will be called rivafb.
808 bool "Enable DDC Support"
812 This enables I2C support for nVidia Chipsets. This is used
813 only for getting EDID information from the attached display
814 allowing for robust video mode handling and switching.
816 Because fbdev-2.6 requires that drivers must be able to
817 independently validate video mode parameters, you should say Y
821 bool "Lots of debug output from Riva(nVidia) driver"
825 Say Y here if you want the Riva driver to output all sorts
826 of debugging information to provide to the maintainer when
827 something goes wrong.
829 config FB_RIVA_BACKLIGHT
830 bool "Support for backlight control"
834 Say Y here if you want to control the backlight of your display.
837 tristate "Intel 810/815 support (EXPERIMENTAL)"
838 depends on FB && EXPERIMENTAL && PCI && X86_32
841 select FB_MODE_HELPERS
842 select FB_CFB_FILLRECT
843 select FB_CFB_COPYAREA
844 select FB_CFB_IMAGEBLIT
847 This driver supports the on-board graphics built in to the Intel 810
848 and 815 chipsets. Say Y if you have and plan to use such a board.
850 To compile this driver as a module, choose M here: the
851 module will be called i810fb.
853 For more information, please read
854 <file:Documentation/fb/intel810.txt>
857 bool "use VESA Generalized Timing Formula"
860 If you say Y, then the VESA standard, Generalized Timing Formula
861 or GTF, will be used to calculate the required video timing values
862 per video mode. Since the GTF allows nondiscrete timings
863 (nondiscrete being a range of values as opposed to discrete being a
864 set of values), you'll be able to use any combination of horizontal
865 and vertical resolutions, and vertical refresh rates without having
866 to specify your own timing parameters. This is especially useful
867 to maximize the performance of an aging display, or if you just
868 have a display with nonstandard dimensions. A VESA compliant
869 monitor is recommended, but can still work with non-compliant ones.
870 If you need or want this, then select this option. The timings may
871 not be compliant with Intel's recommended values. Use at your own
874 If you say N, the driver will revert to discrete video timings
875 using a set recommended by Intel in their documentation.
880 bool "Enable DDC Support"
881 depends on FB_I810 && FB_I810_GTF
886 tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G support (EXPERIMENTAL)"
887 depends on FB && EXPERIMENTAL && PCI && X86
890 select FB_MODE_HELPERS
891 select FB_CFB_FILLRECT
892 select FB_CFB_COPYAREA
893 select FB_CFB_IMAGEBLIT
895 This driver supports the on-board graphics built in to the Intel
896 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM chipsets.
897 Say Y if you have and plan to use such a board.
899 If you say Y here and want DDC/I2C support you must first say Y to
900 "I2C support" and "I2C bit-banging support" in the character devices
903 If you say M here then "I2C support" and "I2C bit-banging support"
904 can be build either as modules or built-in.
906 To compile this driver as a module, choose M here: the
907 module will be called intelfb.
909 For more information, please read <file:Documentation/fb/intelfb.txt>
911 config FB_INTEL_DEBUG
912 bool "Intel driver Debug Messages"
915 Say Y here if you want the Intel driver to output all sorts
916 of debugging information to provide to the maintainer when
917 something goes wrong.
920 bool "DDC/I2C for Intel framebuffer support"
925 Say Y here if you want DDC/I2C support for your on-board Intel graphics.
928 tristate "Matrox acceleration"
930 select FB_CFB_FILLRECT
931 select FB_CFB_COPYAREA
932 select FB_CFB_IMAGEBLIT
933 select FB_TILEBLITTING
934 select FB_MACMODES if PPC_PMAC
936 Say Y here if you have a Matrox Millennium, Matrox Millennium II,
937 Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox
938 Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video,
939 Matrox G400, G450 or G550 card in your box.
941 To compile this driver as a module, choose M here: the
942 module will be called matroxfb.
944 You can pass several parameters to the driver at boot time or at
945 module load time. The parameters look like "video=matrox:XXX", and
946 are described in <file:Documentation/fb/matroxfb.txt>.
948 config FB_MATROX_MILLENIUM
949 bool "Millennium I/II support"
952 Say Y here if you have a Matrox Millennium or Matrox Millennium II
953 video card. If you select "Advanced lowlevel driver options" below,
954 you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp
955 packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can
956 also use font widths different from 8.
958 config FB_MATROX_MYSTIQUE
959 bool "Mystique support"
962 Say Y here if you have a Matrox Mystique or Matrox Mystique 220
963 video card. If you select "Advanced lowlevel driver options" below,
964 you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp
965 packed pixel and 32 bpp packed pixel. You can also use font widths
969 bool "G100/G200/G400/G450/G550 support"
972 Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based
973 video card. If you select "Advanced lowlevel driver options", you
974 should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed
975 pixel and 32 bpp packed pixel. You can also use font widths
978 If you need support for G400 secondary head, you must first say Y to
979 "I2C support" in the character devices section, and then to
980 "Matrox I2C support" and "G400 second head support" here in the
981 framebuffer section. G450/G550 secondary head and digital output
982 are supported without additional modules.
984 The driver starts in monitor mode. You must use the matroxset tool
985 (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to
986 swap primary and secondary head outputs, or to change output mode.
987 Secondary head driver always start in 640x480 resolution and you
988 must use fbset to change it.
990 Do not forget that second head supports only 16 and 32 bpp
991 packed pixels, so it is a good idea to compile them into the kernel
992 too. You can use only some font widths, as the driver uses generic
993 painting procedures (the secondary head does not use acceleration
996 G450/G550 hardware can display TV picture only from secondary CRTC,
997 and it performs no scaling, so picture must have 525 or 625 lines.
1000 tristate "Matrox I2C support"
1001 depends on FB_MATROX
1004 This drivers creates I2C buses which are needed for accessing the
1005 DDC (I2C) bus present on all Matroxes, an I2C bus which
1006 interconnects Matrox optional devices, like MGA-TVO on G200 and
1007 G400, and the secondary head DDC bus, present on G400 only.
1009 You can say Y or M here if you want to experiment with monitor
1010 detection code. You must say Y or M here if you want to use either
1011 second head of G400 or MGA-TVO on G200 or G400.
1013 If you compile it as module, it will create a module named
1016 config FB_MATROX_MAVEN
1017 tristate "G400 second head support"
1018 depends on FB_MATROX_G && FB_MATROX_I2C
1020 WARNING !!! This support does not work with G450 !!!
1022 Say Y or M here if you want to use a secondary head (meaning two
1023 monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary
1024 head is not compatible with accelerated XFree 3.3.x SVGA servers -
1025 secondary head output is blanked while you are in X. With XFree
1026 3.9.17 preview you can use both heads if you use SVGA over fbdev or
1027 the fbdev driver on first head and the fbdev driver on second head.
1029 If you compile it as module, two modules are created,
1030 matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for
1031 both G200 and G400, matroxfb_crtc2 is needed only by G400. You must
1032 also load i2c-matroxfb to get it to run.
1034 The driver starts in monitor mode and you must use the matroxset
1036 <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to
1037 PAL or NTSC or to swap primary and secondary head outputs.
1038 Secondary head driver also always start in 640x480 resolution, you
1039 must use fbset to change it.
1041 Also do not forget that second head supports only 16 and 32 bpp
1042 packed pixels, so it is a good idea to compile them into the kernel
1043 too. You can use only some font widths, as the driver uses generic
1044 painting procedures (the secondary head does not use acceleration
1047 config FB_MATROX_MULTIHEAD
1048 bool "Multihead support"
1049 depends on FB_MATROX
1051 Say Y here if you have more than one (supported) Matrox device in
1052 your computer and you want to use all of them for different monitors
1053 ("multihead"). If you have only one device, you should say N because
1054 the driver compiled with Y is larger and a bit slower, especially on
1057 If you said M to "Matrox unified accelerated driver" and N here, you
1058 will still be able to use several Matrox devices simultaneously:
1059 insert several instances of the module matroxfb into the kernel
1060 with insmod, supplying the parameter "dev=N" where N is 0, 1, etc.
1061 for the different Matrox devices. This method is slightly faster but
1062 uses 40 KB of kernel memory per Matrox card.
1064 There is no need for enabling 'Matrox multihead support' if you have
1065 only one Matrox card in the box.
1068 tristate "ATI Radeon display support"
1069 depends on FB && PCI
1070 select FB_BACKLIGHT if FB_RADEON_BACKLIGHT
1071 select FB_MODE_HELPERS
1072 select FB_CFB_FILLRECT
1073 select FB_CFB_COPYAREA
1074 select FB_CFB_IMAGEBLIT
1075 select FB_MACMODES if PPC_OF
1077 Choose this option if you want to use an ATI Radeon graphics card as
1078 a framebuffer device. There are both PCI and AGP versions. You
1079 don't need to choose this to run the Radeon in plain VGA mode.
1081 If you say Y here and want DDC/I2C support you must first say Y to
1082 "I2C support" and "I2C bit-banging support" in the character devices
1085 If you say M here then "I2C support" and "I2C bit-banging support"
1086 can be build either as modules or built-in.
1088 There is a product page at
1089 http://apps.ati.com/ATIcompare/
1091 config FB_RADEON_I2C
1092 bool "DDC/I2C for ATI Radeon support"
1093 depends on FB_RADEON
1097 Say Y here if you want DDC/I2C support for your Radeon board.
1099 config FB_RADEON_BACKLIGHT
1100 bool "Support for backlight control"
1101 depends on FB_RADEON
1104 Say Y here if you want to control the backlight of your display.
1106 config FB_RADEON_DEBUG
1107 bool "Lots of debug output from Radeon driver"
1108 depends on FB_RADEON
1111 Say Y here if you want the Radeon driver to output all sorts
1112 of debugging information to provide to the maintainer when
1113 something goes wrong.
1116 tristate "ATI Rage128 display support"
1117 depends on FB && PCI
1118 select FB_CFB_FILLRECT
1119 select FB_CFB_COPYAREA
1120 select FB_CFB_IMAGEBLIT
1121 select FB_BACKLIGHT if FB_ATY128_BACKLIGHT
1122 select FB_MACMODES if PPC_PMAC
1124 This driver supports graphics boards with the ATI Rage128 chips.
1125 Say Y if you have such a graphics board and read
1126 <file:Documentation/fb/aty128fb.txt>.
1128 To compile this driver as a module, choose M here: the
1129 module will be called aty128fb.
1131 config FB_ATY128_BACKLIGHT
1132 bool "Support for backlight control"
1133 depends on FB_ATY128
1136 Say Y here if you want to control the backlight of your display.
1139 tristate "ATI Mach64 display support" if PCI || ATARI
1140 depends on FB && !SPARC32
1141 select FB_CFB_FILLRECT
1142 select FB_CFB_COPYAREA
1143 select FB_CFB_IMAGEBLIT
1144 select FB_BACKLIGHT if FB_ATY_BACKLIGHT
1145 select FB_MACMODES if PPC
1147 This driver supports graphics boards with the ATI Mach64 chips.
1148 Say Y if you have such a graphics board.
1150 To compile this driver as a module, choose M here: the
1151 module will be called atyfb.
1154 bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support"
1155 depends on PCI && FB_ATY
1156 default y if SPARC64 && FB_PCI
1158 Say Y here to support use of ATI's 64-bit Rage boards (or other
1159 boards based on the Mach64 CT, VT, GT, and LT chipsets) as a
1160 framebuffer device. The ATI product support page for these boards
1161 is at <http://support.ati.com/products/pc/mach64/>.
1163 config FB_ATY_GENERIC_LCD
1164 bool "Mach64 generic LCD support (EXPERIMENTAL)"
1165 depends on FB_ATY_CT
1167 Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility,
1168 Rage XC, or Rage XL chipset.
1171 bool "Mach64 GX support" if PCI
1175 Say Y here to support use of the ATI Mach64 Graphics Expression
1176 board (or other boards based on the Mach64 GX chipset) as a
1177 framebuffer device. The ATI product support page for these boards
1179 <http://support.ati.com/products/pc/mach64/graphics_xpression.html>.
1181 config FB_ATY_BACKLIGHT
1182 bool "Support for backlight control"
1186 Say Y here if you want to control the backlight of your display.
1189 tristate "S3 Trio/Virge support"
1190 depends on FB && PCI
1191 select FB_CFB_FILLRECT
1192 select FB_CFB_COPYAREA
1193 select FB_CFB_IMAGEBLIT
1194 select FB_TILEBLITTING
1198 Driver for graphics boards with S3 Trio / S3 Virge chip.
1201 tristate "S3 Savage support"
1202 depends on FB && PCI && EXPERIMENTAL
1203 select FB_MODE_HELPERS
1204 select FB_CFB_FILLRECT
1205 select FB_CFB_COPYAREA
1206 select FB_CFB_IMAGEBLIT
1209 This driver supports notebooks and computers with S3 Savage PCI/AGP
1212 Say Y if you have such a graphics card.
1214 To compile this driver as a module, choose M here; the module
1215 will be called savagefb.
1217 config FB_SAVAGE_I2C
1218 bool "Enable DDC2 Support"
1219 depends on FB_SAVAGE
1222 This enables I2C support for S3 Savage Chipsets. This is used
1223 only for getting EDID information from the attached display
1224 allowing for robust video mode handling and switching.
1226 Because fbdev-2.6 requires that drivers must be able to
1227 independently validate video mode parameters, you should say Y
1230 config FB_SAVAGE_ACCEL
1231 bool "Enable Console Acceleration"
1232 depends on FB_SAVAGE
1235 This option will compile in console acceleration support. If
1236 the resulting framebuffer console has bothersome glitches, then
1240 tristate "SiS/XGI display support"
1241 depends on FB && PCI
1242 select FB_CFB_FILLRECT
1243 select FB_CFB_COPYAREA
1244 select FB_CFB_IMAGEBLIT
1246 This is the frame buffer device driver for the SiS 300, 315, 330
1247 and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets.
1248 Specs available at <http://www.sis.com> and <http://www.xgitech.com>.
1250 To compile this driver as a module, choose M here; the module
1251 will be called sisfb.
1254 bool "SiS 300 series support"
1257 Say Y here to support use of the SiS 300/305, 540, 630 and 730.
1260 bool "SiS 315/330/340 series and XGI support"
1263 Say Y here to support use of the SiS 315, 330 and 340 series
1264 (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well
1265 as XGI V3XT, V5, V8 and Z7.
1268 tristate "NeoMagic display support"
1269 depends on FB && PCI
1270 select FB_MODE_HELPERS
1271 select FB_CFB_FILLRECT
1272 select FB_CFB_COPYAREA
1273 select FB_CFB_IMAGEBLIT
1276 This driver supports notebooks with NeoMagic PCI chips.
1277 Say Y if you have such a graphics card.
1279 To compile this driver as a module, choose M here: the
1280 module will be called neofb.
1283 tristate "IMG Kyro support"
1284 depends on FB && PCI
1285 select FB_CFB_FILLRECT
1286 select FB_CFB_COPYAREA
1287 select FB_CFB_IMAGEBLIT
1289 Say Y here if you have a STG4000 / Kyro / PowerVR 3 based
1292 To compile this driver as a module, choose M here: the
1293 module will be called kyrofb.
1296 tristate "3Dfx Banshee/Voodoo3 display support"
1297 depends on FB && PCI
1298 select FB_CFB_IMAGEBLIT
1299 select FB_CFB_FILLRECT
1300 select FB_CFB_COPYAREA
1302 This driver supports graphics boards with the 3Dfx Banshee/Voodoo3
1303 chips. Say Y if you have such a graphics board.
1305 To compile this driver as a module, choose M here: the
1306 module will be called tdfxfb.
1308 config FB_3DFX_ACCEL
1309 bool "3Dfx Banshee/Voodoo3 Acceleration functions (EXPERIMENTAL)"
1310 depends on FB_3DFX && EXPERIMENTAL
1312 This will compile the 3Dfx Banshee/Voodoo3 frame buffer device
1313 with acceleration functions.
1317 tristate "3Dfx Voodoo Graphics (sst1) support"
1318 depends on FB && PCI
1319 select FB_CFB_FILLRECT
1320 select FB_CFB_COPYAREA
1321 select FB_CFB_IMAGEBLIT
1323 Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or
1324 Voodoo2 (cvg) based graphics card.
1326 To compile this driver as a module, choose M here: the
1327 module will be called sstfb.
1329 WARNING: Do not use any application that uses the 3D engine
1330 (namely glide) while using this driver.
1331 Please read the <file:Documentation/fb/README-sstfb.txt> for supported
1332 options and other important info support.
1335 tristate "Cyberblade/i1 support"
1336 depends on FB && PCI && X86_32 && !64BIT
1337 select FB_CFB_IMAGEBLIT
1340 This driver is supposed to support the Trident Cyberblade/i1
1341 graphics core integrated in the VIA VT8601A North Bridge,
1342 also known as VIA Apollo PLE133.
1345 - Developed, tested and working on EPIA 5000 and EPIA 800.
1346 - Does work reliable on all systems with CRT/LCD connected to
1348 - Should work on systems that do use the internal LCD port, but
1349 this is absolutely not tested.
1351 Character imageblit, copyarea and rectangle fill are hw accelerated,
1352 ypan scrolling is used by default.
1354 Please do read <file:Documentation/fb/cyblafb/*>.
1356 To compile this driver as a module, choose M here: the
1357 module will be called cyblafb.
1360 tristate "Trident support"
1361 depends on FB && PCI
1362 select FB_CFB_FILLRECT
1363 select FB_CFB_COPYAREA
1364 select FB_CFB_IMAGEBLIT
1366 This driver is supposed to support graphics boards with the
1367 Trident CyberXXXX/Image/CyberBlade chips mostly found in laptops
1368 but also on some motherboards. For more information, read
1369 <file:Documentation/fb/tridentfb.txt>
1371 Cyberblade/i1 support will be removed soon, use the cyblafb driver
1374 Say Y if you have such a graphics board.
1377 To compile this driver as a module, choose M here: the
1378 module will be called tridentfb.
1380 config FB_TRIDENT_ACCEL
1381 bool "Trident Acceleration functions (EXPERIMENTAL)"
1382 depends on FB_TRIDENT && EXPERIMENTAL
1384 This will compile the Trident frame buffer device with
1385 acceleration functions.
1388 tristate "Permedia3 support"
1389 depends on FB && PCI && BROKEN
1391 This is the frame buffer device driver for the 3DLabs Permedia3
1392 chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 &
1393 similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000
1394 and maybe other boards.
1397 bool "Au1100 LCD Driver"
1398 depends on (FB = y) && EXPERIMENTAL && PCI && MIPS && MIPS_PB1100=y
1401 bool "Au1200 LCD Driver"
1402 depends on (FB = y) && MIPS && SOC_AU1200
1403 select FB_CFB_FILLRECT
1404 select FB_CFB_COPYAREA
1405 select FB_CFB_IMAGEBLIT
1407 This is the framebuffer driver for the AMD Au1200 SOC. It can drive
1408 various panels and CRTs by passing in kernel cmd line option
1409 au1200fb:panel=<name>.
1411 source "drivers/video/geode/Kconfig"
1414 bool "Creator/Creator3D/Elite3D support"
1415 depends on FB_SBUS && SPARC64
1416 select FB_CFB_COPYAREA
1417 select FB_CFB_IMAGEBLIT
1419 This is the frame buffer device driver for the Creator, Creator3D,
1420 and Elite3D graphics boards.
1423 bool "TCX (SS4/SS5 only) support"
1425 select FB_CFB_FILLRECT
1426 select FB_CFB_COPYAREA
1427 select FB_CFB_IMAGEBLIT
1429 This is the frame buffer device driver for the TCX 24/8bit frame
1433 bool "CGfourteen (SX) support"
1435 select FB_CFB_FILLRECT
1436 select FB_CFB_COPYAREA
1437 select FB_CFB_IMAGEBLIT
1439 This is the frame buffer device driver for the CGfourteen frame
1440 buffer on Desktop SPARCsystems with the SX graphics option.
1443 bool "P9100 (Sparcbook 3 only) support"
1445 select FB_CFB_FILLRECT
1446 select FB_CFB_COPYAREA
1447 select FB_CFB_IMAGEBLIT
1449 This is the frame buffer device driver for the P9100 card
1450 supported on Sparcbook 3 machines.
1453 bool "Leo (ZX) support"
1455 select FB_CFB_FILLRECT
1456 select FB_CFB_COPYAREA
1457 select FB_CFB_IMAGEBLIT
1459 This is the frame buffer device driver for the SBUS-based Sun ZX
1460 (leo) frame buffer cards.
1463 bool "Sun XVR-500 3DLABS Wildcat support"
1464 depends on FB && PCI && SPARC64
1465 select FB_CFB_FILLRECT
1466 select FB_CFB_COPYAREA
1467 select FB_CFB_IMAGEBLIT
1469 This is the framebuffer device for the Sun XVR-500 and similar
1470 graphics cards based upon the 3DLABS Wildcat chipset. The driver
1471 only works on sparc64 systems where the system firwmare has
1472 mostly initialized the card already. It is treated as a
1473 completely dumb framebuffer device.
1476 bool "Sun XVR-2500 3DLABS Wildcat support"
1477 depends on FB && PCI && SPARC64
1478 select FB_CFB_FILLRECT
1479 select FB_CFB_COPYAREA
1480 select FB_CFB_IMAGEBLIT
1482 This is the framebuffer device for the Sun XVR-2500 and similar
1483 graphics cards based upon the 3DLABS Wildcat chipset. The driver
1484 only works on sparc64 systems where the system firwmare has
1485 mostly initialized the card already. It is treated as a
1486 completely dumb framebuffer device.
1489 bool "PCI framebuffers"
1490 depends on (FB = y) && PCI && SPARC
1493 bool "IGA 168x display support"
1494 depends on SPARC32 && FB_PCI
1495 select FB_CFB_FILLRECT
1496 select FB_CFB_COPYAREA
1497 select FB_CFB_IMAGEBLIT
1499 This is the framebuffer device for the INTERGRAPHICS 1680 and
1500 successor frame buffer cards.
1503 tristate "HD64461 Frame Buffer support"
1504 depends on FB && HD64461
1505 select FB_CFB_FILLRECT
1506 select FB_CFB_COPYAREA
1507 select FB_CFB_IMAGEBLIT
1509 This is the frame buffer device driver for the Hitachi HD64461 LCD
1513 bool "PMAG-AA TURBOchannel framebuffer support"
1514 depends on (FB = y) && TC
1515 select FB_CFB_FILLRECT
1516 select FB_CFB_COPYAREA
1517 select FB_CFB_IMAGEBLIT
1519 Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1)
1520 used mainly in the MIPS-based DECstation series.
1523 tristate "PMAG-BA TURBOchannel framebuffer support"
1525 select FB_CFB_FILLRECT
1526 select FB_CFB_COPYAREA
1527 select FB_CFB_IMAGEBLIT
1529 Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8)
1530 used mainly in the MIPS-based DECstation series.
1533 tristate "PMAGB-B TURBOchannel framebuffer support"
1535 select FB_CFB_FILLRECT
1536 select FB_CFB_COPYAREA
1537 select FB_CFB_IMAGEBLIT
1539 Support for the PMAGB-B TURBOchannel framebuffer card used mainly
1540 in the MIPS-based DECstation series. The card is currently only
1541 supported in 1280x1024x8 mode.
1544 bool "Maxine (Personal DECstation) onboard framebuffer support"
1545 depends on (FB = y) && MACH_DECSTATION
1546 select FB_CFB_FILLRECT
1547 select FB_CFB_COPYAREA
1548 select FB_CFB_IMAGEBLIT
1550 Support for the onboard framebuffer (1024x768x8) in the Personal
1551 DECstation series (Personal DECstation 5000/20, /25, /33, /50,
1555 bool "TMPTX3912/PR31700 frame buffer support"
1556 depends on (FB = y) && NINO
1557 select FB_CFB_FILLRECT
1558 select FB_CFB_COPYAREA
1559 select FB_CFB_IMAGEBLIT
1561 The TX3912 is a Toshiba RISC processor based on the MIPS 3900 core
1562 see <http://www.toshiba.com/taec/components/Generic/risc/tx3912.htm>.
1564 Say Y here to enable kernel support for the on-board framebuffer.
1567 bool "G364 frame buffer support"
1568 depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700)
1569 select FB_CFB_FILLRECT
1570 select FB_CFB_COPYAREA
1571 select FB_CFB_IMAGEBLIT
1573 The G364 driver is the framebuffer used in MIPS Magnum 4000 and
1574 Olivetti M700-10 systems.
1577 bool "Motorola 68328 native frame buffer support"
1578 depends on (FB = y) && (M68328 || M68EZ328 || M68VZ328)
1579 select FB_CFB_FILLRECT
1580 select FB_CFB_COPYAREA
1581 select FB_CFB_IMAGEBLIT
1583 Say Y here if you want to support the built-in frame buffer of
1584 the Motorola 68328 CPU family.
1587 tristate "PXA LCD framebuffer support"
1588 depends on FB && ARCH_PXA
1589 select FB_CFB_FILLRECT
1590 select FB_CFB_COPYAREA
1591 select FB_CFB_IMAGEBLIT
1593 Frame buffer driver for the built-in LCD controller in the Intel
1596 This driver is also available as a module ( = code which can be
1597 inserted and removed from the running kernel whenever you want). The
1598 module will be called pxafb. If you want to compile it as a module,
1599 say M here and read <file:Documentation/kbuild/modules.txt>.
1603 config FB_PXA_PARAMETERS
1604 bool "PXA LCD command line parameters"
1608 Enable the use of kernel command line or module parameters
1609 to configure the physical properties of the LCD panel when
1610 using the PXA LCD driver.
1612 This option allows you to override the panel parameters
1613 supplied by the platform in order to support multiple
1614 different models of flatpanel. If you will only be using a
1615 single model of flatpanel then you can safely leave this
1618 <file:Documentation/fb/pxafb.txt> describes the available parameters.
1621 tristate "2700G LCD framebuffer support"
1622 depends on FB && ARCH_PXA
1623 select FB_CFB_FILLRECT
1624 select FB_CFB_COPYAREA
1625 select FB_CFB_IMAGEBLIT
1627 Framebuffer driver for the Intel 2700G (Marathon) Graphics
1631 bool "Enable debugging info via debugfs"
1632 depends on FB_MBX && DEBUG_FS
1635 Enable this if you want debugging information using the debug
1636 filesystem (debugfs)
1641 tristate "W100 frame buffer support"
1642 depends on FB && PXA_SHARPSL
1643 select FB_CFB_FILLRECT
1644 select FB_CFB_COPYAREA
1645 select FB_CFB_IMAGEBLIT
1647 Frame buffer driver for the w100 as found on the Sharp SL-Cxx series.
1649 This driver is also available as a module ( = code which can be
1650 inserted and removed from the running kernel whenever you want). The
1651 module will be called w100fb. If you want to compile it as a module,
1652 say M here and read <file:Documentation/kbuild/modules.txt>.
1657 tristate "S3C2410 LCD framebuffer support"
1658 depends on FB && ARCH_S3C2410
1659 select FB_CFB_FILLRECT
1660 select FB_CFB_COPYAREA
1661 select FB_CFB_IMAGEBLIT
1663 Frame buffer driver for the built-in LCD controller in the Samsung
1666 This driver is also available as a module ( = code which can be
1667 inserted and removed from the running kernel whenever you want). The
1668 module will be called s3c2410fb. If you want to compile it as a module,
1669 say M here and read <file:Documentation/kbuild/modules.txt>.
1672 config FB_S3C2410_DEBUG
1673 bool "S3C2410 lcd debug messages"
1674 depends on FB_S3C2410
1676 Turn on debugging messages. Note that you can set/unset at run time
1680 tristate "Silicon Motion SM501 framebuffer support"
1681 depends on FB && MFD_SM501
1682 select FB_CFB_FILLRECT
1683 select FB_CFB_COPYAREA
1684 select FB_CFB_IMAGEBLIT
1686 Frame buffer driver for the CRT and LCD controllers in the Silicon
1689 This driver is also available as a module ( = code which can be
1690 inserted and removed from the running kernel whenever you want). The
1691 module will be called sm501fb. If you want to compile it as a module,
1692 say M here and read <file:Documentation/modules.txt>.
1697 config FB_PNX4008_DUM
1698 tristate "Display Update Module support on Philips PNX4008 board"
1699 depends on FB && ARCH_PNX4008
1701 Say Y here to enable support for PNX4008 Display Update Module (DUM)
1703 config FB_PNX4008_DUM_RGB
1704 tristate "RGB Framebuffer support on Philips PNX4008 board"
1705 depends on FB_PNX4008_DUM
1706 select FB_CFB_FILLRECT
1707 select FB_CFB_COPYAREA
1708 select FB_CFB_IMAGEBLIT
1710 Say Y here to enable support for PNX4008 RGB Framebuffer
1712 config FB_IBM_GXT4500
1713 tristate "Framebuffer support for IBM GXT4500P adaptor"
1715 select FB_CFB_FILLRECT
1716 select FB_CFB_COPYAREA
1717 select FB_CFB_IMAGEBLIT
1719 Say Y here to enable support for the IBM GXT4500P display
1720 adaptor, found on some IBM System P (pSeries) machines.
1723 bool "PS3 GPU framebuffer driver"
1724 depends on (FB = y) && PS3_PS3AV
1725 select FB_CFB_FILLRECT
1726 select FB_CFB_COPYAREA
1727 select FB_CFB_IMAGEBLIT
1729 Include support for the virtual frame buffer in the PS3 platform.
1731 config FB_PS3_DEFAULT_SIZE_M
1732 int "PS3 default frame buffer size (in MiB)"
1736 This is the default size (in MiB) of the virtual frame buffer in
1738 The default value can be overridden on the kernel command line
1739 using the "ps3fb" option (e.g. "ps3fb=9M");
1742 tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
1744 select FB_SYS_FILLRECT
1745 select FB_SYS_COPYAREA
1746 select FB_SYS_IMAGEBLIT
1749 This is a `virtual' frame buffer device. It operates on a chunk of
1750 unswappable kernel memory instead of on the memory of a graphics
1751 board. This means you cannot see any output sent to this frame
1752 buffer device, while it does consume precious memory. The main use
1753 of this frame buffer device is testing and debugging the frame
1754 buffer subsystem. Do NOT enable it for normal systems! To protect
1755 the innocent, it has to be enabled explicitly at boot time using the
1756 kernel option `video=vfb:'.
1758 To compile this driver as a module, choose M here: the
1759 module will be called vfb. In order to load it, you must use
1760 the vfb_enable=1 option.
1765 source "drivers/video/console/Kconfig"
1768 if FB || SGI_NEWPORT_CONSOLE
1769 source "drivers/video/logo/Kconfig"