[PATCH] i386: put HOTPLUG_CPU under Processor type, not Bus options

[powerpc.git] / arch / i386 / Kconfig

diff --git a/arch/i386/Kconfig b/arch/i386/Kconfig
index 968fabd..cbde675 100644 (file)
--- a/arch/i386/Kconfig
+++ b/arch/i386/Kconfig
@@ -29,10 +29,6 @@ config MMU
 config SBUS
        bool
 
 config SBUS
        bool
 

-config UID16
-       bool
-       default y
-

 config GENERIC_ISA_DMA
        bool
        default y
 config GENERIC_ISA_DMA
        bool
        default y


@@ -45,8 +41,21 @@ config ARCH_MAY_HAVE_PC_FDC
        bool
        default y
 
        bool
        default y
 

+config DMI
+       bool
+       default y
+

 source "init/Kconfig"
 
 source "init/Kconfig"
 

+config DOUBLEFAULT
+       default y
+       bool "Enable doublefault exception handler" if EMBEDDED
+       help
+          This option allows trapping of rare doublefault exceptions that
+          would otherwise cause a system to silently reboot. Disabling this
+          option saves about 4k and might cause you much additional grey
+          hair.
+

 menu "Processor type and features"
 
 choice
 menu "Processor type and features"
 
 choice


@@ -630,10 +639,6 @@ config REGPARM
        and passes the first three arguments of a function call in registers.
        This will probably break binary only modules.
 
        and passes the first three arguments of a function call in registers.
        This will probably break binary only modules.
 

-       This feature is only enabled for gcc-3.0 and later - earlier compilers
-       generate incorrect output with certain kernel constructs when
-       -mregparm=3 is used.
-

 config SECCOMP
        bool "Enable seccomp to safely compute untrusted bytecode"
        depends on PROC_FS
 config SECCOMP
        bool "Enable seccomp to safely compute untrusted bytecode"
        depends on PROC_FS


@@ -653,17 +658,6 @@ config SECCOMP
 
 source kernel/Kconfig.hz
 
 
 source kernel/Kconfig.hz
 

-config PHYSICAL_START
-       hex "Physical address where the kernel is loaded" if EMBEDDED
-       default "0x100000"
-       help
-         This gives the physical address where the kernel is loaded.
-         Primarily used in the case of kexec on panic where the
-         fail safe kernel needs to run at a different address than
-         the panic-ed kernel.
-
-         Don't change this unless you know what you are doing.
-

 config KEXEC
        bool "kexec system call (EXPERIMENTAL)"
        depends on EXPERIMENTAL
 config KEXEC
        bool "kexec system call (EXPERIMENTAL)"
        depends on EXPERIMENTAL


@@ -683,11 +677,40 @@ config KEXEC
 
 config CRASH_DUMP
        bool "kernel crash dumps (EXPERIMENTAL)"
 
 config CRASH_DUMP
        bool "kernel crash dumps (EXPERIMENTAL)"

-       depends on EMBEDDED

        depends on EXPERIMENTAL
        depends on HIGHMEM
        help
          Generate crash dump after being started by kexec.
        depends on EXPERIMENTAL
        depends on HIGHMEM
        help
          Generate crash dump after being started by kexec.

+
+config PHYSICAL_START
+       hex "Physical address where the kernel is loaded" if (EMBEDDED || CRASH_DUMP)
+
+       default "0x1000000" if CRASH_DUMP
+       default "0x100000"
+       help
+         This gives the physical address where the kernel is loaded. Normally
+         for regular kernels this value is 0x100000 (1MB). But in the case
+         of kexec on panic the fail safe kernel needs to run at a different
+         address than the panic-ed kernel. This option is used to set the load
+         address for kernels used to capture crash dump on being kexec'ed
+         after panic. The default value for crash dump kernels is
+         0x1000000 (16MB). This can also be set based on the "X" value as
+         specified in the "crashkernel=YM@XM" command line boot parameter
+         passed to the panic-ed kernel. Typically this parameter is set as
+         crashkernel=64M@16M. Please take a look at
+         Documentation/kdump/kdump.txt for more details about crash dumps.
+
+         Don't change this unless you know what you are doing.
+
+config HOTPLUG_CPU
+       bool "Support for hot-pluggable CPUs (EXPERIMENTAL)"
+       depends on SMP && HOTPLUG && EXPERIMENTAL
+       ---help---
+         Say Y here to experiment with turning CPUs off and on.  CPUs
+         can be controlled through /sys/devices/system/cpu.
+
+         Say N.
+

 endmenu
 
 
 endmenu
 
 


@@ -703,7 +726,7 @@ depends on PM && !X86_VISWS
 
 config APM
        tristate "APM (Advanced Power Management) BIOS support"
 
 config APM
        tristate "APM (Advanced Power Management) BIOS support"

-       depends on PM && PM_LEGACY
+       depends on PM

        ---help---
          APM is a BIOS specification for saving power using several different
          techniques. This is mostly useful for battery powered laptops with
        ---help---
          APM is a BIOS specification for saving power using several different
          techniques. This is mostly useful for battery powered laptops with


@@ -974,15 +997,6 @@ config SCx200
          This support is also available as a module.  If compiled as a
          module, it will be called scx200.
 
          This support is also available as a module.  If compiled as a
          module, it will be called scx200.
 

-config HOTPLUG_CPU
-       bool "Support for hot-pluggable CPUs (EXPERIMENTAL)"
-       depends on SMP && HOTPLUG && EXPERIMENTAL
-       ---help---
-         Say Y here to experiment with turning CPUs off and on.  CPUs
-         can be controlled through /sys/devices/system/cpu.
-
-         Say N.
-

 source "drivers/pcmcia/Kconfig"
 
 source "drivers/pci/hotplug/Kconfig"
 source "drivers/pcmcia/Kconfig"
 
 source "drivers/pci/hotplug/Kconfig"


@@ -1059,3 +1073,7 @@ config X86_TRAMPOLINE
        bool
        depends on X86_SMP || (X86_VOYAGER && SMP)
        default y
        bool
        depends on X86_SMP || (X86_VOYAGER && SMP)
        default y

+
+config KTIME_SCALAR
+       bool
+       default y