-//! MSP430F1612/1611 clock and I/O definitions
-
-#include "platform.h"
-
-#include <signal.h>
-#include <io.h>
-#include <iomacros.h>
-
-
-//! Receive a byte.
-unsigned char serial_rx(){
- char c;
-
- while(!(IFG1&URXIFG0));//wait for a byte
- c = RXBUF0;
- IFG1&=~URXIFG0;
- U0TCTL &= ~URXSE;
-
- return c;
-}
-//! Transmit a byte.
-void serial_tx(unsigned char x){
- while ((IFG1 & UTXIFG0) == 0); //loop until buffer is free
- TXBUF0 = x;
-}
-
-//! Set the baud rate.
-void setbaud(unsigned char rate){
-
- //http://mspgcc.sourceforge.net/baudrate.html
- switch(rate){
- case 1://9600 baud
- UBR00=0x7F; UBR10=0x01; UMCTL0=0x5B; /* uart0 3683400Hz 9599bps */
- break;
- case 2://19200 baud
- UBR00=0xBF; UBR10=0x00; UMCTL0=0xF7; /* uart0 3683400Hz 19194bps */
- break;
- case 3://38400 baud
- UBR00=0x5F; UBR10=0x00; UMCTL0=0xBF; /* uart0 3683400Hz 38408bps */
- break;
- case 4://57600 baud
- UBR00=0x40; UBR10=0x00; UMCTL0=0x00; /* uart0 3683400Hz 57553bps */
- break;
- default:
- case 5://115200 baud
- UBR00=0x20; UBR10=0x00; UMCTL0=0x00; /* uart0 3683400Hz 115106bps */
- break;
- }
-}
-
-void msp430_init_uart(){
-
- /* RS232 */
-
- P3SEL |= BIT4|BIT5; // P3.4,5 = USART0 TXD/RXD
- P3DIR |= BIT4;
-
- UCTL0 = SWRST | CHAR; /* 8-bit character, UART mode */
- UTCTL0 = SSEL1; /* UCLK = MCLK */
-
- setbaud(0);
-
- ME1 &= ~USPIE0; /* USART1 SPI module disable */
- ME1 |= (UTXE0 | URXE0); /* Enable USART1 TXD/RXD */
-
- UCTL0 &= ~SWRST;
-
- /* XXX Clear pending interrupts before enable!!! */
- U0TCTL |= URXSE;
-
-
- //IE1 |= URXIE1; /* Enable USART1 RX interrupt */
-}
-
-
-void msp430_init_dco() {
- /* This code taken from the FU Berlin sources and reformatted. */
- //
-
-//Works well.
-//#define MSP430_CPU_SPEED 2457600UL
-
-//Too fast for internal resistor.
-//#define MSP430_CPU_SPEED 4915200UL
-
-//Max speed.
-//#deefine MSP430_CPU_SPEED 4500000UL
-
-//baud rate speed
-#define MSP430_CPU_SPEED 3683400UL
-#define DELTA ((MSP430_CPU_SPEED) / (32768 / 8))
- unsigned int compare, oldcapture = 0;
- unsigned int i;
-
- WDTCTL = WDTPW + WDTHOLD; //stop WDT
-
-
- DCOCTL=0xF0;
- //a4
- //1100
-
- /* ACLK is devided by 4. RSEL=6 no division for MCLK
- and SSMCLK. XT2 is off. */
- //BCSCTL1 = 0xa8;
-
- BCSCTL2 = 0x00; /* Init FLL to desired frequency using the 32762Hz
- crystal DCO frquenzy = 2,4576 MHz */
-
- P1OUT|=1;
-
- BCSCTL1 |= DIVA1 + DIVA0; /* ACLK = LFXT1CLK/8 */
- for(i = 0xffff; i > 0; i--) { /* Delay for XTAL to settle */
- asm("nop");
- }
-
- CCTL2 = CCIS0 + CM0 + CAP; // Define CCR2, CAP, ACLK
- TACTL = TASSEL1 + TACLR + MC1; // SMCLK, continous mode
-
-
- while(1) {
-
- while((CCTL2 & CCIFG) != CCIFG); /* Wait until capture occured! */
- CCTL2 &= ~CCIFG; /* Capture occured, clear flag */
- compare = CCR2; /* Get current captured SMCLK */
- compare = compare - oldcapture; /* SMCLK difference */
- oldcapture = CCR2; /* Save current captured SMCLK */
-
- if(DELTA == compare) {
- break; /* if equal, leave "while(1)" */
- } else if(DELTA < compare) { /* DCO is too fast, slow it down */
- DCOCTL--;
- if(DCOCTL == 0xFF) { /* Did DCO role under? */
- BCSCTL1--;
- }
- } else { /* -> Select next lower RSEL */
- DCOCTL++;
- if(DCOCTL == 0x00) { /* Did DCO role over? */
- BCSCTL1++;
- }
- /* -> Select next higher RSEL */
- }
- }
-
- CCTL2 = 0; /* Stop CCR2 function */
- TACTL = 0; /* Stop Timer_A */
-
- BCSCTL1 &= ~(DIVA1 + DIVA0); /* remove /8 divisor from ACLK again */
-
- P1OUT=0;
-}