- Default: 1
- For auto-loading more than one card, specify this
option together with snd-card-X aliases.
-
+ slots - Reserve the slot index for the given driver.
+ This option takes multiple strings.
+ See "Module Autoloading Support" section for details.
Module snd-pcm-oss
------------------
Module snd-cmipci
-----------------
- Module for C-Media CMI8338 and 8738 PCI sound cards.
+ Module for C-Media CMI8338/8738/8768/8770 PCI sound cards.
- mpu_port - 0x300,0x310,0x320,0x330 = legacy port,
- 1 = integrated PCI port,
+ mpu_port - port address of MIDI interface (8338 only):
+ 0x300,0x310,0x320,0x330 = legacy port,
0 = disable (default)
- fm_port - 0x388 = legacy port,
- 1 = integrated PCI port (default),
+ fm_port - port address of OPL-3 FM synthesizer (8x38 only):
+ 0x388 = legacy port,
+ 1 = integrated PCI port (default on 8738),
0 = disable
soft_ac3 - Software-conversion of raw SPDIF packets (model 033 only)
(default = 1)
single_cmd - Use single immediate commands to communicate with
codecs (for debugging only)
enable_msi - Enable Message Signaled Interrupt (MSI) (default = off)
+ power_save - Automatic power-saving timtout (in second, 0 =
+ disable)
+ power_save_controller - Reset HD-audio controller in power-saving mode
+ (default = on)
This module supports one card and autoprobe.
fujitsu Fujitsu Laptop
hp-bpc HP xw4400/6400/8400/9400 laptops
hp-bpc-d7000 HP BPC D7000
+ hp-tc-t5735 HP Thin Client T5735
benq Benq ED8
benq-t31 Benq T31
hippo Hippo (ATI) with jack detection, Sony UX-90s
hippo_1 Hippo (Benq) with jack detection
sony-assamd Sony ASSAMD
+ ultra Samsung Q1 Ultra Vista model
basic fixed pin assignment w/o SPDIF
auto auto-config reading BIOS (default)
ALC268
3stack 3-stack model
+ toshiba Toshiba A205
+ acer Acer laptops
auto auto-config reading BIOS (default)
ALC662
3stack-6ch-dig 3-stack (6-channel) with SPDIF
6stack-dig 6-stack with SPDIF
lenovo-101e Lenovo laptop
+ eeepc-p701 ASUS Eeepc
auto auto-config reading BIOS (default)
ALC882/885
3stack-dig 3-jack with SPDIF I/O
6stack-dig 6-jack digital with SPDIF I/O
arima Arima W820Di1
+ targa Targa T8, MSI-1049 T8
+ asus-a7j ASUS A7J
+ asus-a7m ASUS A7M
macpro MacPro support
+ mbp3 Macbook Pro rev3
imac24 iMac 24'' with jack detection
w2jc ASUS W2JC
auto auto-config reading BIOS (default)
3stack-6ch-dig 3-jack 6-channel with SPDIF I/O
6stack-dig-demo 6-jack digital for Intel demo board
acer Acer laptops (Travelmate 3012WTMi, Aspire 5600, etc)
+ acer-aspire Acer Aspire 9810
medion Medion Laptops
medion-md2 Medion MD2
targa-dig Targa/MSI
lenovo-101e Lenovo 101E
lenovo-nb0763 Lenovo NB0763
lenovo-ms7195-dig Lenovo MS7195
+ haier-w66 Haier W66
6stack-hp HP machines with 6stack (Nettle boards)
3stack-hp HP machines with 3stack (Lucknow, Samba boards)
auto auto-config reading BIOS (default)
3stack-660-digout 3-jack with SPDIF OUT (for ALC660VD)
lenovo Lenovo 3000 C200
dallas Dallas laptops
+ hp HP TX1000
auto auto-config reading BIOS (default)
CMI9880
3stack 3-stack, shared surrounds
laptop 2-channel only (FSC V2060, Samsung M50)
laptop-eapd 2-channel with EAPD (Samsung R65, ASUS A6J)
+ laptop-automute 2-channel with EAPD and HP-automute (Lenovo N100)
ultra 2-channel with EAPD (Samsung Ultra tablet PC)
AD1988
can be adjusted. Appearing only when compiled with
$CONFIG_SND_DEBUG=y
- STAC9200/9205/9254
+ STAC9200
+ ref Reference board
+ dell-d21 Dell (unknown)
+ dell-d22 Dell (unknown)
+ dell-d23 Dell (unknown)
+ dell-m21 Dell Inspiron 630m, Dell Inspiron 640m
+ dell-m22 Dell Latitude D620, Dell Latitude D820
+ dell-m23 Dell XPS M1710, Dell Precision M90
+ dell-m24 Dell Latitude 120L
+ dell-m25 Dell Inspiron E1505n
+ dell-m26 Dell Inspiron 1501
+ dell-m27 Dell Inspiron E1705/9400
+ gateway Gateway laptops with EAPD control
+
+ STAC9205/9254
ref Reference board
+ dell-m42 Dell (unknown)
+ dell-m43 Dell Precision
+ dell-m44 Dell Inspiron
STAC9220/9221
ref Reference board
3stack D945 3stack
5stack D945 5stack + SPDIF
- dell Dell XPS M1210
intel-mac-v1 Intel Mac Type 1
intel-mac-v2 Intel Mac Type 2
intel-mac-v3 Intel Mac Type 3
macbook-pro Intel Mac Book Pro 2nd generation (eq. type 3)
imac-intel Intel iMac (eq. type 2)
imac-intel-20 Intel iMac (newer version) (eq. type 3)
+ dell-d81 Dell (unknown)
+ dell-d82 Dell (unknown)
+ dell-m81 Dell (unknown)
+ dell-m82 Dell XPS M1210
STAC9202/9250/9251
ref Reference board, base config
ref Reference board
3stack D965 3stack
5stack D965 5stack + SPDIF
- dell-3stack Dell E520
+ dell-3stack Dell Dimension E520
STAC9872
vaio Setup for VAIO FE550G/SZ110
subsystem ID (output of "lspci -nv") to ALSA BTS or alsa-devel
ML (see the section "Links and Addresses").
+ power_save and power_save_controller options are for power-saving
+ mode. See powersave.txt for details.
+
Note 2: If you get click noises on output, try the module option
position_fix=1 or 2. position_fix=1 will use the SD_LPIB
register value without FIFO size correction as the current
* Chaintech 9CJS
* Chaintech AV-710
* Shuttle SN25P
+ * Onkyo SE-90PCI
+ * Onkyo SE-200PCI
model - Use the given board model, one of the following:
revo51, revo71, amp2000, prodigy71, prodigy71lt,
prodigy192, aureon51, aureon71, universe, ap192,
- k8x800, phase22, phase28, ms300, av710
+ k8x800, phase22, phase28, ms300, av710, se200pci,
+ se90pci
This module supports multiple cards and autoprobe.
port - port number or -1 (disable)
irq - IRQ number or -1 (disable)
pnp - PnP detection - 0 = disable, 1 = enable (default)
- uart_enter - Issue UART_ENTER command at open - bool, default = on
This module supports multiple devices and PnP.
The power-management is supported.
+ Module snd-sc6000
+ -----------------
+
+ Module for Gallant SC-6000 soundcard.
+
+ port - Port # (0x220 or 0x240)
+ mss_port - MSS Port # (0x530 or 0xe80)
+ irq - IRQ # (5,7,9,10,11)
+ mpu_irq - MPU-401 IRQ # (5,7,9,10) ,0 - no MPU-401 irq
+ dma - DMA # (1,3,0)
+
+ This module supports multiple cards.
+
+ This card is also known as Audio Excel DSP 16 or Zoltrix AV302.
+
Module snd-sgalaxy
------------------
Module for ENSONIQ SoundScape PnP cards.
port - Port # (PnP setup)
+ wss_port - WSS Port # (PnP setup)
irq - IRQ # (PnP setup)
mpu_irq - MPU-401 IRQ # (PnP setup)
dma - DMA # (PnP setup)
+ dma2 - 2nd DMA # (PnP setup, -1 to disable)
This module supports multiple cards. ISA PnP must be enabled.
You need sscape_ctl tool in alsa-tools package for loading
dma2 - DMA2 # for CS4232 PCM interface.
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+ The below are options for wavefront_synth features:
+ wf_raw - Assume that we need to boot the OS (default:no)
+ If yes, then during driver loading, the state of the board is
+ ignored, and we reset the board and load the firmware anyway.
+ fx_raw - Assume that the FX process needs help (default:yes)
+ If false, we'll leave the FX processor in whatever state it is
+ when the driver is loaded. The default is to download the
+ microprogram and associated coefficients to set it up for
+ "default" operation, whatever that means.
+ debug_default - Debug parameters for card initialization
+ wait_usecs - How long to wait without sleeping, usecs
+ (default:150)
+ This magic number seems to give pretty optimal throughput
+ based on my limited experimentation.
+ If you want to play around with it and find a better value, be
+ my guest. Remember, the idea is to get a number that causes us
+ to just busy wait for as many WaveFront commands as possible,
+ without coming up with a number so large that we hog the whole
+ CPU.
+ Specifically, with this number, out of about 134,000 status
+ waits, only about 250 result in a sleep.
+ sleep_interval - How long to sleep when waiting for reply
+ (default: 100)
+ sleep_tries - How many times to try sleeping during a wait
+ (default: 50)
+ ospath - Pathname to processed ICS2115 OS firmware
+ (default:wavefront.os)
+ The path name of the ISC2115 OS firmware. In the recent
+ version, it's handled via firmware loader framework, so it
+ must be installed in the proper path, typically,
+ /lib/firmware.
+ reset_time - How long to wait for a reset to take effect
+ (default:2)
+ ramcheck_time - How many seconds to wait for the RAM test
+ (default:20)
+ osrun_time - How many seconds to wait for the ICS2115 OS
+ (default:10)
+
This module supports multiple cards and ISA PnP.
+ Note: the firmware file "wavefront.os" was located in the earlier
+ version in /etc. Now it's loaded via firmware loader, and
+ must be in the proper firmware path, such as /lib/firmware.
+ Copy (or symlink) the file appropriately if you get an error
+ regarding firmware downloading after upgrading the kernel.
+
Module snd-sonicvibes
---------------------
In this example, the interwave card is always loaded as the first card
(index 0) and ens1371 as the second (index 1).
+Alternative (and new) way to fixate the slot assignment is to use
+"slots" option of snd module. In the case above, specify like the
+following:
+
+options snd slots=snd-interwave,snd-ens1371
+
+Then, the first slot (#0) is reserved for snd-interwave driver, and
+the second (#1) for snd-ens1371. You can omit index option in each
+driver if slots option is used (although you can still have them at
+the same time as long as they don't conflict).
+
+The slots option is especially useful for avoiding the possible
+hot-plugging and the resultant slot conflict. For example, in the
+case above again, the first two slots are already reserved. If any
+other driver (e.g. snd-usb-audio) is loaded before snd-interwave or
+snd-ens1371, it will be assigned to the third or later slot.
+
ALSA PCM devices to OSS devices mapping
=======================================
projects / powerpc.git / blobdiff