also generate such events.
The bit mask allows some control over which hot keys generate ACPI
-events. Not all bits in the mask can be modified. Not all bits that
-can be modified do anything. Not all hot keys can be individually
-controlled by the mask. Most recent ThinkPad models honor the
-following bits (assuming the hot keys feature has been enabled):
-
- key bit behavior when set behavior when unset
-
- Fn-F3 always generates ACPI event
- Fn-F4 always generates ACPI event
- Fn-F5 0010 generate ACPI event enable/disable Bluetooth
- Fn-F7 0040 generate ACPI event switch LCD and external display
- Fn-F8 0080 generate ACPI event expand screen or none
- Fn-F9 0100 generate ACPI event none
- Fn-F12 always generates ACPI event
-
-Some models do not support all of the above. For example, the T30 does
-not support Fn-F5 and Fn-F9. Other models do not support the mask at
-all. On those models, hot keys cannot be controlled individually.
+events. Not all bits in the mask can be modified. Not all bits that can
+be modified do anything. Not all hot keys can be individually controlled
+by the mask. Some models do not support the mask at all. On those
+models, hot keys cannot be controlled individually.
Note that enabling ACPI events for some keys prevents their default
-behavior. For example, if events for Fn-F5 are enabled, that key will
-no longer enable/disable Bluetooth by itself. This can still be done
-from an acpid handler for the ibm/hotkey event.
+behavior. For example, if events for Fn-F5 are enabled, that key will no
+longer enable/disable Bluetooth by itself. This can still be done from
+an acpid handler for the ibm/hotkey event.
+
+On some models, even enabling/disabling the entire hot key feature may
+change the way some keys behave (e.g. in a T43, Fn+F4 will generate an
+button/sleep ACPI event if hot keys are disabled, and it will ignore its
+mask when hot keys are enabled, so the key always does something. On a
+X40, Fn+F4 respects its mask status, but generates the button/sleep ACPI
+event if masked off).
Note also that not all Fn key combinations are supported through
ACPI. For example, on the X40, the brightness, volume and "Access IBM"
echo enable > /proc/acpi/ibm/hotkey -- enable the hot keys feature
echo disable > /proc/acpi/ibm/hotkey -- disable the hot keys feature
- echo 0xffff > /proc/acpi/ibm/hotkey -- enable all possible hot keys
- echo 0x0000 > /proc/acpi/ibm/hotkey -- disable all possible hot keys
- ... any other 4-hex-digit mask ...
+ echo 0xffffffff > /proc/acpi/ibm/hotkey -- enable all hot keys
+ echo 0 > /proc/acpi/ibm/hotkey -- disable all possible hot keys
+ ... any other 8-hex-digit mask ...
echo reset > /proc/acpi/ibm/hotkey -- restore the original mask
sysfs notes:
key (see above). Returns the current status of the hot
keys mask, and allows one to modify it.
+ hotkey_all_mask:
+ bit mask that should enable event reporting for all
+ supported hot keys, when echoed to hotkey_mask above.
+ Unless you know which events need to be handled
+ passively (because the firmware *will* handle them
+ anyway), do *not* use hotkey_all_mask. Use
+ hotkey_recommended_mask, instead. You have been warned.
+
+ hotkey_recommended_mask:
+ bit mask that should enable event reporting for all
+ supported hot keys, except those which are handled by
+ the firmware. Echo it to hotkey_mask above, to use.
+
Bluetooth
---------
2: System board, left side (near PCMCIA slot), reported as HDAPS temp
3: PCMCIA slot
9: MCH (northbridge) to DRAM Bus
-10: ICH (southbridge), under Mini-PCI card, under touchpad
+10: Clock-generator, mini-pci card and ICH (southbridge), under Mini-PCI
+ card, under touchpad
11: Power regulator, underside of system board, below F2 key
The A31 has a very atypical layout for the thermal sensors