- Experimental: embedded controller register dump
- LCD brightness control
- Volume control
- - Experimental: fan speed, fan enable/disable
+ - Fan control and monitoring: fan speed, fan enable/disable
- Experimental: WAN enable and disable
A compatibility table by model and feature is maintained on the web
subsystems are not documented here, nor are they tracked by this
attribute.
-Hot keys -- /proc/acpi/ibm/hotkey
----------------------------------
+Hot keys
+--------
+
+procfs: /proc/acpi/ibm/hotkey
+sysfs device attribute: hotkey/*
Without this driver, only the Fn-F4 key (sleep button) generates an
ACPI event. With the driver loaded, the hotkey feature enabled and the
addition, the lid microswitch and some docking station buttons may
also generate such events.
-The following commands can be written to this file:
-
- echo enable > /proc/acpi/ibm/hotkey -- enable the hot keys feature
- echo disable > /proc/acpi/ibm/hotkey -- disable the hot keys feature
- echo 0xffff > /proc/acpi/ibm/hotkey -- enable all possible hot keys
- echo 0x0000 > /proc/acpi/ibm/hotkey -- disable all possible hot keys
- ... any other 4-hex-digit mask ...
- echo reset > /proc/acpi/ibm/hotkey -- restore the original mask
-
The bit mask allows some control over which hot keys generate ACPI
events. Not all bits in the mask can be modified. Not all bits that
can be modified do anything. Not all hot keys can be individually
be used through the "ThinkPad Buttons" utility, see
http://www.nongnu.org/tpb/
-Bluetooth -- /proc/acpi/ibm/bluetooth
--------------------------------------
+procfs notes:
+
+The following commands can be written to the /proc/acpi/ibm/hotkey file:
+
+ echo enable > /proc/acpi/ibm/hotkey -- enable the hot keys feature
+ echo disable > /proc/acpi/ibm/hotkey -- disable the hot keys feature
+ echo 0xffff > /proc/acpi/ibm/hotkey -- enable all possible hot keys
+ echo 0x0000 > /proc/acpi/ibm/hotkey -- disable all possible hot keys
+ ... any other 4-hex-digit mask ...
+ echo reset > /proc/acpi/ibm/hotkey -- restore the original mask
+
+sysfs notes:
+
+ The hot keys attributes are in a hotkey/ subdirectory off the
+ thinkpad device.
+
+ bios_enabled:
+ Returns the status of the hot keys feature when
+ thinkpad-acpi was loaded. Upon module unload, the hot
+ key feature status will be restored to this value.
+
+ 0: hot keys were disabled
+ 1: hot keys were enabled
+
+ bios_mask:
+ Returns the hot keys mask when thinkpad-acpi was loaded.
+ Upon module unload, the hot keys mask will be restored
+ to this value.
+
+ enable:
+ Enables/disables the hot keys feature, and reports
+ current status of the hot keys feature.
+
+ 0: disables the hot keys feature / feature disabled
+ 1: enables the hot keys feature / feature enabled
+
+ mask:
+ bit mask to enable ACPI event generation for each hot
+ key (see above). Returns the current status of the hot
+ keys mask, and allows one to modify it.
+
+
+Bluetooth
+---------
-This feature shows the presence and current state of a Bluetooth
-device. If Bluetooth is installed, the following commands can be used:
+procfs: /proc/acpi/ibm/bluetooth
+sysfs device attribute: bluetooth/enable
+
+This feature shows the presence and current state of a ThinkPad
+Bluetooth device in the internal ThinkPad CDC slot.
+
+Procfs notes:
+
+If Bluetooth is installed, the following commands can be used:
echo enable > /proc/acpi/ibm/bluetooth
echo disable > /proc/acpi/ibm/bluetooth
+Sysfs notes:
+
+ If the Bluetooth CDC card is installed, it can be enabled /
+ disabled through the "bluetooth/enable" thinkpad-acpi device
+ attribute, and its current status can also be queried.
+
+ enable:
+ 0: disables Bluetooth / Bluetooth is disabled
+ 1: enables Bluetooth / Bluetooth is enabled.
+
+ Note: this interface will be probably be superseeded by the
+ generic rfkill class.
+
Video output control -- /proc/acpi/ibm/video
--------------------------------------------
up or down command (the level command will not unmute the volume).
The current volume level and mute state is shown in the file.
-EXPERIMENTAL: fan speed, fan enable/disable
--------------------------------------------
+Fan control and monitoring: fan speed, fan enable/disable
+---------------------------------------------------------
procfs: /proc/acpi/ibm/fan
sysfs device attributes: (hwmon) fan_input, pwm1, pwm1_enable
-This feature is marked EXPERIMENTAL because the implementation
-directly accesses hardware registers and may not work as expected. USE
-WITH CAUTION! To use this feature, you need to supply the
-experimental=1 parameter when loading the module.
+NOTE NOTE NOTE: fan control operations are disabled by default for
+safety reasons. To enable them, the module parameter "fan_control=1"
+must be given to thinkpad-acpi.
This feature attempts to show the current fan speed, control mode and
other fan data that might be available. The speed is read directly
from the hardware registers of the embedded controller. This is known
-to work on later R, T and X series ThinkPads but may show a bogus
+to work on later R, T, X and Z series ThinkPads but may show a bogus
value on other models.
Fan levels:
The sysfs interface follows the hwmon subsystem guidelines for the most
part, and the exception is the fan safety watchdog.
+Writes to any of the sysfs attributes may return the EINVAL error if
+that operation is not supported in a given ThinkPad or if the parameter
+is out-of-bounds, and EPERM if it is forbidden. They may also return
+EINTR (interrupted system call), and EIO (I/O error while trying to talk
+to the firmware).
+
+Features not yet implemented by the driver return ENOSYS.
+
hwmon device attribute pwm1_enable:
0: PWM offline (fan is set to full-speed mode)
1: Manual PWM control (use pwm1 to set fan level)
2: Hardware PWM control (EC "auto" mode)
3: reserved (Software PWM control, not implemented yet)
- Modes 0 and 2 are not supported by all ThinkPads, and the driver
- is not always able to detect this. If it does know a mode is
- unsupported, it will return -EINVAL.
+ Modes 0 and 2 are not supported by all ThinkPads, and the
+ driver is not always able to detect this. If it does know a
+ mode is unsupported, it will return -EINVAL.
hwmon device attribute pwm1:
Fan level, scaled from the firmware values of 0-7 to the hwmon
To stop the fan: set pwm1 to zero, and pwm1_enable to 1.
To start the fan in a safe mode: set pwm1_enable to 2. If that fails
-with ENOTSUP, set it to 1 and set pwm1 to at least 128 (255 would be the
-safest choice, though).
+with EINVAL, try to set pwm1_enable to 1 and pwm1 to at least 128 (255
+would be the safest choice, though).
-EXPERIMENTAL: WAN -- /proc/acpi/ibm/wan
----------------------------------------
+EXPERIMENTAL: WAN
+-----------------
+
+procfs: /proc/acpi/ibm/wan
+sysfs device attribute: wwan/enable
This feature is marked EXPERIMENTAL because the implementation
directly accesses hardware registers and may not work as expected. USE
WITH CAUTION! To use this feature, you need to supply the
experimental=1 parameter when loading the module.
-This feature shows the presence and current state of a WAN (Sierra
-Wireless EV-DO) device. If WAN is installed, the following commands can
-be used:
+This feature shows the presence and current state of a W-WAN (Sierra
+Wireless EV-DO) device.
+
+It was tested on a Lenovo Thinkpad X60. It should probably work on other
+Thinkpad models which come with this module installed.
+
+Procfs notes:
+
+If the W-WAN card is installed, the following commands can be used:
echo enable > /proc/acpi/ibm/wan
echo disable > /proc/acpi/ibm/wan
-It was tested on a Lenovo Thinkpad X60. It should probably work on other
-Thinkpad models which come with this module installed.
+Sysfs notes:
+
+ If the W-WAN card is installed, it can be enabled /
+ disabled through the "wwan/enable" thinkpad-acpi device
+ attribute, and its current status can also be queried.
+
+ enable:
+ 0: disables WWAN card / WWAN card is disabled
+ 1: enables WWAN card / WWAN card is enabled.
+
+ Note: this interface will be probably be superseeded by the
+ generic rfkill class.
Multiple Commands, Module Parameters
------------------------------------
projects / powerpc.git / blobdiff