bool
default y
+config DMI
+ bool
+ default y
+
source "init/Kconfig"
menu "Processor type and features"
config HIGHMEM64G
bool "64GB"
+ depends on X86_CMPXCHG64
help
Select this if you have a 32-bit processor and more than 4
gigabytes of physical RAM.
endchoice
+choice
+ depends on EXPERIMENTAL && !X86_PAE
+ prompt "Memory split"
+ default VMSPLIT_3G
+ help
+ Select the desired split between kernel and user memory.
+
+ If the address range available to the kernel is less than the
+ physical memory installed, the remaining memory will be available
+ as "high memory". Accessing high memory is a little more costly
+ than low memory, as it needs to be mapped into the kernel first.
+ Note that increasing the kernel address space limits the range
+ available to user programs, making the address space there
+ tighter. Selecting anything other than the default 3G/1G split
+ will also likely make your kernel incompatible with binary-only
+ kernel modules.
+
+ If you are not absolutely sure what you are doing, leave this
+ option alone!
+
+ config VMSPLIT_3G
+ bool "3G/1G user/kernel split"
+ config VMSPLIT_3G_OPT
+ bool "3G/1G user/kernel split (for full 1G low memory)"
+ config VMSPLIT_2G
+ bool "2G/2G user/kernel split"
+ config VMSPLIT_1G
+ bool "1G/3G user/kernel split"
+endchoice
+
+config PAGE_OFFSET
+ hex
+ default 0xB0000000 if VMSPLIT_3G_OPT
+ default 0x78000000 if VMSPLIT_2G
+ default 0x40000000 if VMSPLIT_1G
+ default 0xC0000000
+
config HIGHMEM
bool
depends on HIGHMEM64G || HIGHMEM4G
source kernel/Kconfig.hz
-config PHYSICAL_START
- hex "Physical address where the kernel is loaded" if EMBEDDED
- default "0x100000"
- help
- This gives the physical address where the kernel is loaded.
- Primarily used in the case of kexec on panic where the
- fail safe kernel needs to run at a different address than
- the panic-ed kernel.
-
- Don't change this unless you know what you are doing.
-
config KEXEC
bool "kexec system call (EXPERIMENTAL)"
depends on EXPERIMENTAL
config CRASH_DUMP
bool "kernel crash dumps (EXPERIMENTAL)"
- depends on EMBEDDED
depends on EXPERIMENTAL
depends on HIGHMEM
help
Generate crash dump after being started by kexec.
+
+config PHYSICAL_START
+ hex "Physical address where the kernel is loaded" if (EMBEDDED || CRASH_DUMP)
+
+ default "0x1000000" if CRASH_DUMP
+ default "0x100000"
+ help
+ This gives the physical address where the kernel is loaded. Normally
+ for regular kernels this value is 0x100000 (1MB). But in the case
+ of kexec on panic the fail safe kernel needs to run at a different
+ address than the panic-ed kernel. This option is used to set the load
+ address for kernels used to capture crash dump on being kexec'ed
+ after panic. The default value for crash dump kernels is
+ 0x1000000 (16MB). This can also be set based on the "X" value as
+ specified in the "crashkernel=YM@XM" command line boot parameter
+ passed to the panic-ed kernel. Typically this parameter is set as
+ crashkernel=64M@16M. Please take a look at
+ Documentation/kdump/kdump.txt for more details about crash dumps.
+
+ Don't change this unless you know what you are doing.
+
+config HOTPLUG_CPU
+ bool "Support for hot-pluggable CPUs (EXPERIMENTAL)"
+ depends on SMP && HOTPLUG && EXPERIMENTAL && !X86_VOYAGER
+ ---help---
+ Say Y here to experiment with turning CPUs off and on. CPUs
+ can be controlled through /sys/devices/system/cpu.
+
+ Say N.
+
+config DOUBLEFAULT
+ default y
+ bool "Enable doublefault exception handler" if EMBEDDED
+ help
+ This option allows trapping of rare doublefault exceptions that
+ would otherwise cause a system to silently reboot. Disabling this
+ option saves about 4k and might cause you much additional grey
+ hair.
+
endmenu
This support is also available as a module. If compiled as a
module, it will be called scx200.
-config HOTPLUG_CPU
- bool "Support for hot-pluggable CPUs (EXPERIMENTAL)"
- depends on SMP && HOTPLUG && EXPERIMENTAL
- ---help---
- Say Y here to experiment with turning CPUs off and on. CPUs
- can be controlled through /sys/devices/system/cpu.
-
- Say N.
-
source "drivers/pcmcia/Kconfig"
source "drivers/pci/hotplug/Kconfig"
config KPROBES
bool "Kprobes (EXPERIMENTAL)"
+ depends on EXPERIMENTAL && MODULES
help
Kprobes allows you to trap at almost any kernel address and
execute a callback function. register_kprobe() establishes
bool
depends on X86_SMP || (X86_VOYAGER && SMP)
default y
+
+config KTIME_SCALAR
+ bool
+ default y