bool
default n
+config ZONE_DMA
+ bool
+ default y
+
config RWSEM_GENERIC_SPINLOCK
bool
default y
bool
default n
+config ARCH_HAS_ILOG2_U32
+ bool
+ default n
+
+config ARCH_HAS_ILOG2_U64
+ bool
+ default n
+
config GENERIC_FIND_NEXT_BIT
bool
default y
bool
default y
+config GENERIC_HARDIRQS
+ bool
+ default y
+
config GENERIC_CALIBRATE_DELAY
bool
default y
bool
default y
+config NO_IOPORT
+ def_bool y
+
source "init/Kconfig"
menu "Processor type and features"
On many SoC style CPUs the master CPU clock is also used to drive
on-chip peripherals. The clock that is distributed to these
peripherals is sometimes a fixed ratio of the master clock
- frequency. If so then set this to the divider ration of the
+ frequency. If so then set this to the divider ratio of the
master clock to the peripheral clock. If not sure then select 1.
config OLDMASK
Support for the Palm Pilot 1000/5000, Personal/Pro and PalmIII.
config XCOPILOT_BUGS
- bool " (X)Copilot support"
+ bool "(X)Copilot support"
depends on PILOT3
help
Support the bugs of Xcopilot.
+config UC5272
+ bool 'Arcturus Networks uC5272 dimm board support'
+ depends on M5272
+ help
+ Support for the Arcturus Networks uC5272 dimm board.
+
+config UC5282
+ bool "Arcturus Networks uC5282 board support"
+ depends on M528x
+ help
+ Support for the Arcturus Networks uC5282 dimm board.
+
config UCSIMM
bool "uCsimm module support"
depends on M68EZ328
Support for the DragenEngine II board.
config DIRECT_IO_ACCESS
- bool " Allow user to access IO directly"
+ bool "Allow user to access IO directly"
depends on (UCSIMM || UCDIMM || DRAGEN2)
help
Disable the CPU internal registers protection in user mode,
to allow a user application to read/write them.
config INIT_LCD
- bool " Initialize LCD"
+ bool "Initialize LCD"
depends on (UCSIMM || UCDIMM || DRAGEN2)
help
Initialize the LCD controller of the 68x328 processor.
config MEMORY_RESERVE
- int " Memory reservation (MiB)"
+ int "Memory reservation (MiB)"
depends on (UCSIMM || UCDIMM)
help
Reserve certain memory regions on 68x328 based boards.
depends on M528x
help
Support for the EMAC.Inc SOM5282EM module.
+
+config WILDFIRE
+ bool "Intec Automation Inc. WildFire board support"
+ depends on M528x
+ help
+ Support for the Intec Automation Inc. WildFire.
+
+config WILDFIREMOD
+ bool "Intec Automation Inc. WildFire module support"
+ depends on M528x
+ help
+ Support for the Intec Automation Inc. WildFire module.
config ARN5307
bool "Arnewsh 5307 board support"
Support for the Netburner MOD-5272 board.
config ROMFS_FROM_ROM
- bool " ROMFS image not RAM resident"
+ bool "ROMFS image not RAM resident"
depends on (NETtel || SNAPGEAR)
help
The ROMfs filesystem will stay resident in the FLASH/ROM, not be
default y
depends on (AVNET5282)
-config LARGE_ALLOCS
- bool "Allow allocating large blocks (> 1MB) of memory"
- help
- Allow the slab memory allocator to keep chains for very large
- memory sizes - upto 32MB. You may need this if your system has
- a lot of RAM, and you need to able to allocate very large
- contiguous chunks. If unsure, say N.
-
config 4KSTACKS
bool "Use 4Kb for kernel stacks instead of 8Kb"
default y