/**
* jmicron_pre_reset - check for 40/80 pin
* @ap: Port
+ * @deadline: deadline jiffies for the operation
*
* Perform the PATA port setup we need.
-
+ *
* On the Jmicron 361/363 there is a single PATA port that can be mapped
* either as primary or secondary (or neither). We don't do any policy
* and setup here. We assume that has been done by init_one and the
* BIOS.
*/
-static int jmicron_pre_reset(struct ata_port *ap)
+static int jmicron_pre_reset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 control;
ap->cbl = ATA_CBL_SATA;
break;
}
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
/**
.slave_destroy = ata_scsi_slave_destroy,
/* Use standard CHS mapping rules */
.bios_param = ata_std_bios_param,
+#ifdef CONFIG_PM
+ .suspend = ata_scsi_device_suspend,
+ .resume = ata_scsi_device_resume,
+#endif
};
static const struct ata_port_operations jmicron_ops = {
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer,
+ .data_xfer = ata_data_xfer,
/* IRQ-related hooks */
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
/* Generic PATA PCI ATA helpers */
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop,
};
};
struct ata_port_info *port_info[2] = { &info, &info };
- u32 reg;
-
- /* PATA controller is fn 1, AHCI is fn 0 */
- if (id->driver_data != 368 && PCI_FUNC(pdev->devfn) != 1)
- return -ENODEV;
-
- /* The 365/66 have two PATA channels, redirect the second */
- if (id->driver_data == 365 || id->driver_data == 366) {
- pci_read_config_dword(pdev, 0x80, ®);
- reg |= (1 << 24); /* IDE1 to PATA IDE secondary */
- pci_write_config_dword(pdev, 0x80, reg);
- }
-
return ata_pci_init_one(pdev, port_info, 2);
}
-static int jmicron_reinit_one(struct pci_dev *pdev)
-{
- u32 reg;
-
- switch(pdev->device) {
- case PCI_DEVICE_ID_JMICRON_JMB368:
- break;
- case PCI_DEVICE_ID_JMICRON_JMB365:
- case PCI_DEVICE_ID_JMICRON_JMB366:
- /* Restore mapping or disks swap and boy does it get ugly */
- pci_read_config_dword(pdev, 0x80, ®);
- reg |= (1 << 24); /* IDE1 to PATA IDE secondary */
- pci_write_config_dword(pdev, 0x80, reg);
- /* Fall through */
- default:
- /* Make sure AHCI is turned back on */
- pci_write_config_byte(pdev, 0x41, 0xa1);
- }
- return ata_pci_device_resume(pdev);
-}
-
static const struct pci_device_id jmicron_pci_tbl[] = {
- { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB361), 361},
- { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB363), 363},
- { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB365), 365},
- { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB366), 366},
- { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB368), 368},
+ { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361,
+ PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xffff00, 361 },
+ { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363,
+ PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xffff00, 363 },
+ { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365,
+ PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xffff00, 365 },
+ { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366,
+ PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xffff00, 366 },
+ { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368,
+ PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xffff00, 368 },
{ } /* terminate list */
};
.id_table = jmicron_pci_tbl,
.probe = jmicron_init_one,
.remove = ata_pci_remove_one,
+#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
- .resume = jmicron_reinit_one,
+ .resume = ata_pci_device_resume,
+#endif
};
static int __init jmicron_init(void)