#include <linux/libata.h>
#define DRV_NAME "pata_opti"
-#define DRV_VERSION "0.2.7"
+#define DRV_VERSION "0.2.9"
enum {
READ_REG = 0, /* index of Read cycle timing register */
/**
* opti_pre_reset - probe begin
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Set up cable type and use generic probe init
*/
-static int opti_pre_reset(struct ata_port *ap)
+static int opti_pre_reset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits opti_enable_bits[] = {
if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no]))
return -ENOENT;
- ap->cbl = ATA_CBL_PATA40;
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
/**
static void opti_write_reg(struct ata_port *ap, u8 val, int reg)
{
- unsigned long regio = ap->ioaddr.cmd_addr;
+ void __iomem *regio = ap->ioaddr.cmd_addr;
/* These 3 unlock the control register access */
- inw(regio + 1);
- inw(regio + 1);
- outb(3, regio + 2);
+ ioread16(regio + 1);
+ ioread16(regio + 1);
+ iowrite8(3, regio + 2);
/* Do the I/O */
- outb(val, regio + reg);
+ iowrite8(val, regio + reg);
/* Relock */
- outb(0x83, regio + 2);
+ iowrite8(0x83, regio + 2);
}
/**
struct ata_device *pair = ata_dev_pair(adev);
int clock;
int pio = adev->pio_mode - XFER_PIO_0;
- unsigned long regio = ap->ioaddr.cmd_addr;
+ void __iomem *regio = ap->ioaddr.cmd_addr;
u8 addr;
/* Address table precomputed with prefetch off and a DCLK of 2 */
{ 0x58, 0x44, 0x32, 0x22, 0x21 }
};
- outb(0xff, regio + 5);
- clock = inw(regio + 5) & 1;
+ iowrite8(0xff, regio + 5);
+ clock = ioread16(regio + 5) & 1;
/*
* As with many controllers the address setup time is shared
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
+#ifdef CONFIG_PM
.resume = ata_scsi_device_resume,
.suspend = ata_scsi_device_suspend,
+#endif
};
static struct ata_port_operations opti_port_ops = {
.thaw = ata_bmdma_thaw,
.error_handler = opti_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ata_cable_40wire,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer,
+ .data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop
};
static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
.id_table = opti,
.probe = opti_init_one,
.remove = ata_pci_remove_one,
+#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
+#endif
};
static int __init opti_init(void)