[alim7101] Add pci dev table for auto module loading.

[powerpc.git] / drivers / char / watchdog / Kconfig

diff --git a/drivers/char/watchdog/Kconfig b/drivers/char/watchdog/Kconfig
index d53f664..89e46d6 100644 (file)
--- a/drivers/char/watchdog/Kconfig
+++ b/drivers/char/watchdog/Kconfig
@@ -45,7 +45,7 @@ config WATCHDOG_NOWAYOUT
 comment "Watchdog Device Drivers"
        depends on WATCHDOG
 
-# Architecture Independant
+# Architecture Independent
 
 config SOFT_WATCHDOG
        tristate "Software watchdog"
@@ -127,7 +127,7 @@ config S3C2410_WATCHDOG
          enabled.
 
          The driver is limited by the speed of the system's PCLK
-         signal, so with reasonbaly fast systems (PCLK around 50-66MHz)
+         signal, so with reasonably fast systems (PCLK around 50-66MHz)
          then watchdog intervals of over approximately 20seconds are
          unavailable.
 
@@ -165,6 +165,24 @@ config EP93XX_WATCHDOG
          To compile this driver as a module, choose M here: the
          module will be called ep93xx_wdt.
 
+config OMAP_WATCHDOG
+       tristate "OMAP Watchdog"
+       depends on WATCHDOG && (ARCH_OMAP16XX || ARCH_OMAP24XX)
+       help
+         Support for TI OMAP1610/OMAP1710/OMAP2420 watchdog.  Say 'Y' here to
+         enable the OMAP1610/OMAP1710 watchdog timer.
+
+config PNX4008_WATCHDOG
+       tristate "PNX4008 Watchdog"
+       depends on WATCHDOG && ARCH_PNX4008
+       help
+         Say Y here if to include support for the watchdog timer
+         in the PNX4008 processor.
+         This driver can be built as a module by choosing M. The module
+         will be called pnx4008_wdt.
+
+         Say N if you are unsure.
+
 # X86 (i386 + ia64 + x86_64) Architecture
 
 config ACQUIRE_WDT
@@ -298,6 +316,27 @@ config I8XX_TCO
          To compile this driver as a module, choose M here: the
          module will be called i8xx_tco.
 
+config ITCO_WDT
+       tristate "Intel TCO Timer/Watchdog (EXPERIMENTAL)"
+       depends on WATCHDOG && (X86 || IA64) && PCI && EXPERIMENTAL
+       ---help---
+         Hardware driver for the intel TCO timer based watchdog devices.
+         These drivers are included in the Intel 82801 I/O Controller
+         Hub family 'from ICH0 up to ICH7) and in the Intel 6300ESB
+         controller hub.
+
+         The TCO (Total Cost of Ownership) timer is a watchdog timer
+         that will reboot the machine after its second expiration. The
+         expiration time can be configured with the "heartbeat" parameter.
+
+         On some motherboards the driver may fail to reset the chipset's
+         NO_REBOOT flag which prevents the watchdog from rebooting the
+         machine. If this is the case you will get a kernel message like
+         "failed to reset NO_REBOOT flag, reboot disabled by hardware".
+
+         To compile this driver as a module, choose M here: the
+         module will be called iTCO_wdt.
+
 config SC1200_WDT
        tristate "National Semiconductor PC87307/PC97307 (ala SC1200) Watchdog"
        depends on WATCHDOG && X86
@@ -423,7 +462,7 @@ config SBC_EPX_C3_WATCHDOG
          is no way to know if writing to its IO address will corrupt
          your system or have any real effect.  The only way to be sure
          that this driver does what you want is to make sure you
-         are runnning it on an EPX-C3 from Winsystems with the watchdog
+         are running it on an EPX-C3 from Winsystems with the watchdog
          timer at IO address 0x1ee and 0x1ef.  It will write to both those
          IO ports.  Basically, the assumption is made that if you compile
          this driver into your kernel and/or load it as a module, that you
@@ -472,7 +511,7 @@ config INDYDOG
        tristate "Indy/I2 Hardware Watchdog"
        depends on WATCHDOG && SGI_IP22
        help
-         Hardwaredriver for the Indy's/I2's watchdog. This is a
+         Hardware driver for the Indy's/I2's watchdog. This is a
          watchdog timer that will reboot the machine after a 60 second
          timer expired and no process has written to /dev/watchdog during
          that time.
@@ -510,6 +549,14 @@ config SH_WDT
          To compile this driver as a module, choose M here: the
          module will be called shwdt.
 
+config SH_WDT_MMAP
+       bool "Allow mmap of SH WDT"
+       default n
+       depends on SH_WDT
+       help
+         If you say Y here, user applications will be able to mmap the
+         WDT/CPG registers.
+#
 # SPARC64 Architecture
 
 config WATCHDOG_CP1XXX