Support for Compact Flash cards, outboard IDE disks, tape drives,
and CD-ROM drives connected through a PCMCIA card.
+config BLK_DEV_DELKIN
+ tristate "Cardbus IDE support (Delkin/ASKA/Workbit)"
+ depends on CARDBUS && PCI
+ help
+ Support for Delkin, ASKA, and Workbit Cardbus CompactFlash
+ Adapters. This may also work for similar SD and XD adapters.
+
config BLK_DEV_IDECD
tristate "Include IDE/ATAPI CDROM support"
---help---
If both this SCSI emulation and native ATAPI support are compiled
into the kernel, the native support will be used.
+config BLK_DEV_IDEACPI
+ bool "IDE ACPI support"
+ depends on ACPI
+ ---help---
+ Implement ACPI support for generic IDE devices. On modern
+ machines ACPI support is required to properly handle ACPI S3 states.
+
config IDE_TASK_IOCTL
bool "IDE Taskfile Access"
help
config BLK_DEV_GENERIC
tristate "Generic PCI IDE Chipset Support"
depends on BLK_DEV_IDEPCI
+ help
+ This option provides generic support for various PCI IDE Chipsets
+ which otherwise might not be supported.
config BLK_DEV_OPTI621
tristate "OPTi 82C621 chipset enhanced support (EXPERIMENTAL)"
Linux. This may slow disk throughput by a few percent, but at least
things will operate 100% reliably.
-config BLK_DEV_SL82C105
- tristate "Winbond SL82c105 support"
- depends on PCI && (PPC || ARM) && BLK_DEV_IDEPCI
- help
- If you have a Winbond SL82c105 IDE controller, say Y here to enable
- special configuration for this chip. This is common on various CHRP
- motherboards, but could be used elsewhere. If in doubt, say Y.
-
config BLK_DEV_IDEDMA_PCI
bool "Generic PCI bus-master DMA support"
depends on PCI && BLK_DEV_IDEPCI
the kernel to change PIO, DMA and UDMA speeds and to configure
the chip to optimum performance.
+config BLK_DEV_IT8213
+ tristate "IT8213 IDE support"
+ help
+ This driver adds support for the ITE 8213 IDE controller.
+
config BLK_DEV_IT821X
tristate "IT821X IDE support"
help
Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>.
+config BLK_DEV_SL82C105
+ tristate "Winbond SL82c105 support"
+ depends on (PPC || ARM)
+ help
+ If you have a Winbond SL82c105 IDE controller, say Y here to enable
+ special configuration for this chip. This is common on various CHRP
+ motherboards, but could be used elsewhere. If in doubt, say Y.
+
config BLK_DEV_SLC90E66
tristate "SLC90E66 chipset support"
help
This allows the kernel to change PIO, DMA and UDMA speeds and to
configure the chip to optimum performance.
+config BLK_DEV_TC86C001
+ tristate "Toshiba TC86C001 support"
+ help
+ This driver adds support for Toshiba TC86C001 GOKU-S chip.
+
endif
config BLK_DEV_IDE_PMAC
to transfer data to and from memory. Saying Y is safe and improves
performance.
+config BLK_DEV_IDE_CELLEB
+ bool "Toshiba's Cell Reference Set IDE support"
+ depends on PPC_CELLEB
+ help
+ This driver provides support for the built-in IDE controller on
+ Toshiba Cell Reference Board.
+ If unsure, say Y.
+
config BLK_DEV_IDE_SWARM
tristate "IDE for Sibyte evaluation boards"
depends on SIBYTE_SB1xxx_SOC
config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
int "Maximum transfer size (KB) per request (up to 128)"
default "128"
- depends BLK_DEV_IDE_AU1XXX
+ depends on BLK_DEV_IDE_AU1XXX
config IDE_ARM
def_bool ARM && (ARCH_A5K || ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
config BLK_DEV_ALI14XX
tristate "ALI M14xx support"
help
- This driver is enabled at runtime using the "ide0=ali14xx" kernel
+ This driver is enabled at runtime using the "ali14xx.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
I/O speeds to be set as well. See the files
config BLK_DEV_DTC2278
tristate "DTC-2278 support"
help
- This driver is enabled at runtime using the "ide0=dtc2278" kernel
+ This driver is enabled at runtime using the "dtc2278.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the DTC-2278 card, and permits faster I/O speeds to be set as
well. See the <file:Documentation/ide.txt> and
config BLK_DEV_HT6560B
tristate "Holtek HT6560B support"
help
- This driver is enabled at runtime using the "ide0=ht6560b" kernel
+ This driver is enabled at runtime using the "ht6560b.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the Holtek card, and permits faster I/O speeds to be set as well.
See the <file:Documentation/ide.txt> and
config BLK_DEV_QD65XX
tristate "QDI QD65xx support"
help
- This driver is enabled at runtime using the "ide0=qd65xx" kernel
+ This driver is enabled at runtime using the "qd65xx.probe" kernel
boot parameter. It permits faster I/O speeds to be set. See the
<file:Documentation/ide.txt> and <file:drivers/ide/legacy/qd65xx.c> for
more info.
config BLK_DEV_UMC8672
tristate "UMC-8672 support"
help
- This driver is enabled at runtime using the "ide0=umc8672" kernel
+ This driver is enabled at runtime using the "umc8672.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the UMC-8672, and permits faster I/O speeds to be set as well.
See the files <file:Documentation/ide.txt> and
projects / powerpc.git / blobdiff