config SGI_IOC3_ETH
bool "SGI IOC3 Ethernet"
- depends on NET_ETHERNET && PCI && SGI_IP27 && BROKEN
+ depends on NET_ETHERNET && PCI && SGI_IP27
select CRC32
select MII
help
the moment only acceleration of IPv4 is supported. This option
enables offloading for checksums on transmit. If unsure, say Y.
+config MIPS_SIM_NET
+ tristate "MIPS simulator Network device (EXPERIMENTAL)"
+ depends on NETDEVICES && MIPS_SIM && EXPERIMENTAL
+ help
+ The MIPSNET device is a simple Ethernet network device which is
+ emulated by the MIPS Simulator.
+ If you are not using a MIPSsim or are unsure, say N.
+
config SGI_O2MACE_ETH
tristate "SGI O2 MACE Fast Ethernet support"
depends on NET_ETHERNET && SGI_IP32=y
be called ibmveth.
config IBM_EMAC
- bool "IBM PPC4xx EMAC driver support"
+ tristate "PowerPC 4xx on-chip Ethernet support"
depends on 4xx
- select CRC32
- ---help---
- This driver supports the IBM PPC4xx EMAC family of on-chip
- Ethernet controllers.
-
-config IBM_EMAC_ERRMSG
- bool "Verbose error messages"
- depends on IBM_EMAC && BROKEN
+ help
+ This driver supports the PowerPC 4xx EMAC family of on-chip
+ Ethernet controllers.
config IBM_EMAC_RXB
int "Number of receive buffers"
depends on IBM_EMAC
- default "128" if IBM_EMAC4
- default "64"
+ default "128"
config IBM_EMAC_TXB
int "Number of transmit buffers"
depends on IBM_EMAC
- default "128" if IBM_EMAC4
- default "8"
+ default "64"
+
+config IBM_EMAC_POLL_WEIGHT
+ int "MAL NAPI polling weight"
+ depends on IBM_EMAC
+ default "32"
-config IBM_EMAC_FGAP
- int "Frame gap"
+config IBM_EMAC_RX_COPY_THRESHOLD
+ int "RX skb copy threshold (bytes)"
depends on IBM_EMAC
- default "8"
+ default "256"
-config IBM_EMAC_SKBRES
- int "Skb reserve amount"
+config IBM_EMAC_RX_SKB_HEADROOM
+ int "Additional RX skb headroom (bytes)"
depends on IBM_EMAC
default "0"
+ help
+ Additional receive skb headroom. Note, that driver
+ will always reserve at least 2 bytes to make IP header
+ aligned, so usualy there is no need to add any additional
+ headroom.
+
+ If unsure, set to 0.
+
+config IBM_EMAC_PHY_RX_CLK_FIX
+ bool "PHY Rx clock workaround"
+ depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
+ help
+ Enable this if EMAC attached to a PHY which doesn't generate
+ RX clock if there is no link, if this is the case, you will
+ see "TX disable timeout" or "RX disable timeout" in the system
+ log.
+
+ If unsure, say N.
+
+config IBM_EMAC_DEBUG
+ bool "Debugging"
+ depends on IBM_EMAC
+ default n
+
+config IBM_EMAC_ZMII
+ bool
+ depends on IBM_EMAC && (NP405H || NP405L || 44x)
+ default y
+
+config IBM_EMAC_RGMII
+ bool
+ depends on IBM_EMAC && 440GX
+ default y
+
+config IBM_EMAC_TAH
+ bool
+ depends on IBM_EMAC && 440GX
+ default y
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
controller on the Renesas H8/300 processor.
source "drivers/net/fec_8xx/Kconfig"
+source "drivers/net/fs_enet/Kconfig"
endmenu
config GIANFAR
tristate "Gianfar Ethernet"
depends on 85xx || 83xx
+ select PHYLIB
help
This driver supports the Gigabit TSEC on the MPC85xx
family of chips, and the FEC on the 8540
depends on PCI
---help---
This driver supports the 10Gbe XFrame NIC of S2IO.
- For help regarding driver compilation, installation and
- tuning please look into ~/drivers/net/s2io/README.txt.
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/s2io.txt>.
config S2IO_NAPI
bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
If in doubt, say N.
-config 2BUFF_MODE
- bool "Use 2 Buffer Mode on Rx side."
- depends on S2IO
- ---help---
- On enabling the 2 buffer mode, the received frame will be
- split into 2 parts before being DMA'ed to the hosts memory.
- The parts are the ethernet header and ethernet payload.
- This is useful on systems where DMA'ing to to unaligned
- physical memory loactions comes with a heavy price.
- If not sure please say N.
-
endmenu
if !UML
tristate "iSeries Virtual Ethernet driver support"
depends on PPC_ISERIES
+config RIONET
+ tristate "RapidIO Ethernet over messaging driver support"
+ depends on NETDEVICES && RAPIDIO
+
+config RIONET_TX_SIZE
+ int "Number of outbound queue entries"
+ depends on RIONET
+ default "128"
+
+config RIONET_RX_SIZE
+ int "Number of inbound queue entries"
+ depends on RIONET
+ default "128"
+
config FDDI
bool "FDDI driver support"
depends on (PCI || EISA)
module; it is called bsd_comp and will show up in the directory
modules once you have said "make modules". If unsure, say N.
+config PPP_MPPE
+ tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
+ depends on PPP && EXPERIMENTAL
+ select CRYPTO
+ select CRYPTO_SHA1
+ select CRYPTO_ARC4
+ ---help---
+ Support for the MPPE Encryption protocol, as employed by the
+ Microsoft Point-to-Point Tunneling Protocol.
+
+ See http://pptpclient.sourceforge.net/ for information on
+ configuring PPTP clients and servers to utilize this method.
+
config PPPOE
tristate "PPP over Ethernet (EXPERIMENTAL)"
depends on EXPERIMENTAL && PPP
projects / powerpc.git / blobdiff