*
* Copyright (c) 1999 Martin Mares <mj@ucw.cz>
*
+ * Init/reset quirks for USB host controllers should be in the
+ * USB quirks file, where their drivers can access reuse it.
+ *
* The bridge optimization stuff has been removed. If you really
* have a silly BIOS which is unable to set your host bridge right,
* use the PowerTweak utility (see http://powertweak.sourceforge.net).
/*
* PIIX4 ACPI: Two IO regions pointed to by longwords at
* 0x40 (64 bytes of ACPI registers)
- * 0x90 (32 bytes of SMB registers)
+ * 0x90 (16 bytes of SMB registers)
* and a few strange programmable PIIX4 device resources.
*/
static void __devinit quirk_piix4_acpi(struct pci_dev *dev)
pci_read_config_dword(dev, 0x40, ®ion);
quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES, "PIIX4 ACPI");
pci_read_config_dword(dev, 0x90, ®ion);
- quirk_io_region(dev, region, 32, PCI_BRIDGE_RESOURCES+1, "PIIX4 SMB");
+ quirk_io_region(dev, region, 16, PCI_BRIDGE_RESOURCES+1, "PIIX4 SMB");
/* Device resource A has enables for some of the other ones */
pci_read_config_dword(dev, 0x5c, &res_a);
pci_read_config_word(dev, 0x70, &hm);
hm &= PCI_BASE_ADDRESS_IO_MASK;
- quirk_io_region(dev, hm, 128, PCI_BRIDGE_RESOURCES + 1, "vt82c868 HW-mon");
+ quirk_io_region(dev, hm, 128, PCI_BRIDGE_RESOURCES + 1, "vt82c686 HW-mon");
pci_read_config_dword(dev, 0x90, &smb);
smb &= PCI_BASE_ADDRESS_IO_MASK;
- quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 2, "vt82c868 SMB");
+ quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 2, "vt82c686 SMB");
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_vt82c686_acpi );
}
DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irq);
-/*
- * PIIX3 USB: We have to disable USB interrupts that are
- * hardwired to PIRQD# and may be shared with an
- * external device.
- *
- * Legacy Support Register (LEGSUP):
- * bit13: USB PIRQ Enable (USBPIRQDEN),
- * bit4: Trap/SMI On IRQ Enable (USBSMIEN).
- *
- * We mask out all r/wc bits, too.
- */
-static void __devinit quirk_piix3_usb(struct pci_dev *dev)
-{
- u16 legsup;
-
- pci_read_config_word(dev, 0xc0, &legsup);
- legsup &= 0x50ef;
- pci_write_config_word(dev, 0xc0, legsup);
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_2, quirk_piix3_usb );
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_2, quirk_piix3_usb );
-
/*
* VIA VT82C598 has its device ID settable and many BIOSes
* set it to the ID of VT82C597 for backward compatibility.
pci_read_config_byte(dev, 0x77, &val);
}
-
-#define UHCI_USBLEGSUP 0xc0 /* legacy support */
-#define UHCI_USBCMD 0 /* command register */
-#define UHCI_USBSTS 2 /* status register */
-#define UHCI_USBINTR 4 /* interrupt register */
-#define UHCI_USBLEGSUP_DEFAULT 0x2000 /* only PIRQ enable set */
-#define UHCI_USBCMD_RUN (1 << 0) /* RUN/STOP bit */
-#define UHCI_USBCMD_GRESET (1 << 2) /* Global reset */
-#define UHCI_USBCMD_CONFIGURE (1 << 6) /* config semaphore */
-#define UHCI_USBSTS_HALTED (1 << 5) /* HCHalted bit */
-
-#define OHCI_CONTROL 0x04
-#define OHCI_CMDSTATUS 0x08
-#define OHCI_INTRSTATUS 0x0c
-#define OHCI_INTRENABLE 0x10
-#define OHCI_INTRDISABLE 0x14
-#define OHCI_OCR (1 << 3) /* ownership change request */
-#define OHCI_CTRL_IR (1 << 8) /* interrupt routing */
-#define OHCI_INTR_OC (1 << 30) /* ownership change */
-
-#define EHCI_HCC_PARAMS 0x08 /* extended capabilities */
-#define EHCI_USBCMD 0 /* command register */
-#define EHCI_USBCMD_RUN (1 << 0) /* RUN/STOP bit */
-#define EHCI_USBSTS 4 /* status register */
-#define EHCI_USBSTS_HALTED (1 << 12) /* HCHalted bit */
-#define EHCI_USBINTR 8 /* interrupt register */
-#define EHCI_USBLEGSUP 0 /* legacy support register */
-#define EHCI_USBLEGSUP_BIOS (1 << 16) /* BIOS semaphore */
-#define EHCI_USBLEGSUP_OS (1 << 24) /* OS semaphore */
-#define EHCI_USBLEGCTLSTS 4 /* legacy control/status */
-#define EHCI_USBLEGCTLSTS_SOOE (1 << 13) /* SMI on ownership change */
-
-int usb_early_handoff __devinitdata = 0;
-static int __init usb_handoff_early(char *str)
-{
- usb_early_handoff = 1;
- return 0;
-}
-__setup("usb-handoff", usb_handoff_early);
-
-static void __devinit quirk_usb_handoff_uhci(struct pci_dev *pdev)
-{
- unsigned long base = 0;
- int wait_time, delta;
- u16 val, sts;
- int i;
-
- for (i = 0; i < PCI_ROM_RESOURCE; i++)
- if ((pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
- base = pci_resource_start(pdev, i);
- break;
- }
-
- if (!base)
- return;
-
- /*
- * stop controller
- */
- sts = inw(base + UHCI_USBSTS);
- val = inw(base + UHCI_USBCMD);
- val &= ~(u16)(UHCI_USBCMD_RUN | UHCI_USBCMD_CONFIGURE);
- outw(val, base + UHCI_USBCMD);
-
- /*
- * wait while it stops if it was running
- */
- if ((sts & UHCI_USBSTS_HALTED) == 0)
- {
- wait_time = 1000;
- delta = 100;
-
- do {
- outw(0x1f, base + UHCI_USBSTS);
- udelay(delta);
- wait_time -= delta;
- val = inw(base + UHCI_USBSTS);
- if (val & UHCI_USBSTS_HALTED)
- break;
- } while (wait_time > 0);
- }
-
- /*
- * disable interrupts & legacy support
- */
- outw(0, base + UHCI_USBINTR);
- outw(0x1f, base + UHCI_USBSTS);
- pci_read_config_word(pdev, UHCI_USBLEGSUP, &val);
- if (val & 0xbf)
- pci_write_config_word(pdev, UHCI_USBLEGSUP, UHCI_USBLEGSUP_DEFAULT);
-
-}
-
-static void __devinit quirk_usb_handoff_ohci(struct pci_dev *pdev)
-{
- void __iomem *base;
- int wait_time;
-
- base = ioremap_nocache(pci_resource_start(pdev, 0),
- pci_resource_len(pdev, 0));
- if (base == NULL) return;
-
- if (readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
- wait_time = 500; /* 0.5 seconds */
- writel(OHCI_INTR_OC, base + OHCI_INTRENABLE);
- writel(OHCI_OCR, base + OHCI_CMDSTATUS);
- while (wait_time > 0 &&
- readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
- wait_time -= 10;
- msleep(10);
- }
- }
-
- /*
- * disable interrupts
- */
- writel(~(u32)0, base + OHCI_INTRDISABLE);
- writel(~(u32)0, base + OHCI_INTRSTATUS);
-
- iounmap(base);
-}
-
-static void __devinit quirk_usb_disable_ehci(struct pci_dev *pdev)
-{
- int wait_time, delta;
- void __iomem *base, *op_reg_base;
- u32 hcc_params, val, temp;
- u8 cap_length;
-
- base = ioremap_nocache(pci_resource_start(pdev, 0),
- pci_resource_len(pdev, 0));
- if (base == NULL) return;
-
- cap_length = readb(base);
- op_reg_base = base + cap_length;
- hcc_params = readl(base + EHCI_HCC_PARAMS);
- hcc_params = (hcc_params >> 8) & 0xff;
- if (hcc_params) {
- pci_read_config_dword(pdev,
- hcc_params + EHCI_USBLEGSUP,
- &val);
- if (((val & 0xff) == 1) && (val & EHCI_USBLEGSUP_BIOS)) {
- /*
- * Ok, BIOS is in smm mode, try to hand off...
- */
- pci_read_config_dword(pdev,
- hcc_params + EHCI_USBLEGCTLSTS,
- &temp);
- pci_write_config_dword(pdev,
- hcc_params + EHCI_USBLEGCTLSTS,
- temp | EHCI_USBLEGCTLSTS_SOOE);
- val |= EHCI_USBLEGSUP_OS;
- pci_write_config_dword(pdev,
- hcc_params + EHCI_USBLEGSUP,
- val);
-
- wait_time = 500;
- do {
- msleep(10);
- wait_time -= 10;
- pci_read_config_dword(pdev,
- hcc_params + EHCI_USBLEGSUP,
- &val);
- } while (wait_time && (val & EHCI_USBLEGSUP_BIOS));
- if (!wait_time) {
- /*
- * well, possibly buggy BIOS...
- */
- printk(KERN_WARNING "EHCI early BIOS handoff "
- "failed (BIOS bug ?)\n");
- pci_write_config_dword(pdev,
- hcc_params + EHCI_USBLEGSUP,
- EHCI_USBLEGSUP_OS);
- pci_write_config_dword(pdev,
- hcc_params + EHCI_USBLEGCTLSTS,
- 0);
- }
- }
- }
-
- /*
- * halt EHCI & disable its interrupts in any case
- */
- val = readl(op_reg_base + EHCI_USBSTS);
- if ((val & EHCI_USBSTS_HALTED) == 0) {
- val = readl(op_reg_base + EHCI_USBCMD);
- val &= ~EHCI_USBCMD_RUN;
- writel(val, op_reg_base + EHCI_USBCMD);
-
- wait_time = 2000;
- delta = 100;
- do {
- writel(0x3f, op_reg_base + EHCI_USBSTS);
- udelay(delta);
- wait_time -= delta;
- val = readl(op_reg_base + EHCI_USBSTS);
- if ((val == ~(u32)0) || (val & EHCI_USBSTS_HALTED)) {
- break;
- }
- } while (wait_time > 0);
- }
- writel(0, op_reg_base + EHCI_USBINTR);
- writel(0x3f, op_reg_base + EHCI_USBSTS);
-
- iounmap(base);
-
- return;
-}
-
-
-
-static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev)
-{
- if (!usb_early_handoff)
- return;
-
- if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x00)) { /* UHCI */
- quirk_usb_handoff_uhci(pdev);
- } else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x10)) { /* OHCI */
- quirk_usb_handoff_ohci(pdev);
- } else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x20)) { /* EHCI */
- quirk_usb_disable_ehci(pdev);
- }
-
- return;
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_usb_early_handoff);
-
/*
* ... This is further complicated by the fact that some SiS96x south
* bridges pretend to be 85C503/5513 instead. In that case see if we
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_alder_ioapic );
#endif
+enum ide_combined_type { COMBINED = 0, IDE = 1, LIBATA = 2 };
+/* Defaults to combined */
+static enum ide_combined_type combined_mode;
+
+static int __init combined_setup(char *str)
+{
+ if (!strncmp(str, "ide", 3))
+ combined_mode = IDE;
+ else if (!strncmp(str, "libata", 6))
+ combined_mode = LIBATA;
+ else /* "combined" or anything else defaults to old behavior */
+ combined_mode = COMBINED;
+
+ return 1;
+}
+__setup("combined_mode=", combined_setup);
+
#ifdef CONFIG_SCSI_SATA_INTEL_COMBINED
static void __devinit quirk_intel_ide_combined(struct pci_dev *pdev)
{
case 0x27c4:
ich = 7;
break;
+ case 0x2828: /* ICH8M */
+ ich = 8;
+ break;
default:
/* we do not handle this PCI device */
return;
else
return; /* not in combined mode */
} else {
- WARN_ON((ich != 6) && (ich != 7));
+ WARN_ON((ich != 6) && (ich != 7) && (ich != 8));
tmp &= 0x3; /* interesting bits 1:0 */
if (tmp & (1 << 0))
comb = (1 << 2); /* PATA port 0, SATA port 1 */
if (prog & comb)
return;
+ /* Don't reserve any so the IDE driver can get them (but only if
+ * combined_mode=ide).
+ */
+ if (combined_mode == IDE)
+ return;
+
+ /* Grab them both for libata if combined_mode=libata. */
+ if (combined_mode == LIBATA) {
+ request_region(0x1f0, 8, "libata"); /* port 0 */
+ request_region(0x170, 8, "libata"); /* port 1 */
+ return;
+ }
+
/* SATA port is in legacy mode. Reserve port so that
* IDE driver does not attempt to use it. If request_region
* fails, it will be obvious at boot time, so we don't bother
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETMOS, PCI_ANY_ID, quirk_netmos);
+
+static void __devinit fixup_rev1_53c810(struct pci_dev* dev)
+{
+ /* rev 1 ncr53c810 chips don't set the class at all which means
+ * they don't get their resources remapped. Fix that here.
+ */
+
+ if (dev->class == PCI_CLASS_NOT_DEFINED) {
+ printk(KERN_INFO "NCR 53c810 rev 1 detected, setting PCI class.\n");
+ dev->class = PCI_CLASS_STORAGE_SCSI;
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810);
+
+
static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end)
{
while (f < end) {
pci_do_fixups(dev, start, end);
}
+/* Enable 1k I/O space granularity on the Intel P64H2 */
+static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev)
+{
+ u16 en1k;
+ u8 io_base_lo, io_limit_lo;
+ unsigned long base, limit;
+ struct resource *res = dev->resource + PCI_BRIDGE_RESOURCES;
+
+ pci_read_config_word(dev, 0x40, &en1k);
+
+ if (en1k & 0x200) {
+ printk(KERN_INFO "PCI: Enable I/O Space to 1 KB Granularity\n");
+
+ pci_read_config_byte(dev, PCI_IO_BASE, &io_base_lo);
+ pci_read_config_byte(dev, PCI_IO_LIMIT, &io_limit_lo);
+ base = (io_base_lo & (PCI_IO_RANGE_MASK | 0x0c)) << 8;
+ limit = (io_limit_lo & (PCI_IO_RANGE_MASK | 0x0c)) << 8;
+
+ if (base <= limit) {
+ res->start = base;
+ res->end = limit + 0x3ff;
+ }
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x1460, quirk_p64h2_1k_io);
+
EXPORT_SYMBOL(pcie_mch_quirk);
#ifdef CONFIG_HOTPLUG
EXPORT_SYMBOL(pci_fixup_device);