default "4"
help
Set this to the maximum number of serial ports you want
- the kernel to register at boot time. This can be overriden
+ the kernel to register at boot time. This can be overridden
with the module parameter "nr_uarts", or boot-time parameter
8250.nr_uarts
depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
help
Say Y here if you have a Boca serial board. Please read the Boca
- mini-HOWTO, avaialble from <http://www.tldp.org/docs.html#howto>
+ mini-HOWTO, available from <http://www.tldp.org/docs.html#howto>
To compile this driver as a module, choose M here: the module
will be called 8250_boca.
Even if you say Y here, the currently visible framebuffer console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
- "console=ttyAM0". (Try "man bootparam" or see the documentation of
+ "console=ttyAMA0". (Try "man bootparam" or see the documentation of
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
-config SERIAL_AT91
- bool "AT91RM9200 / AT91SAM9261 serial port support"
+config SERIAL_ATMEL
+ bool "AT91 / AT32 on-chip serial port support"
depends on ARM && (ARCH_AT91RM9200 || ARCH_AT91SAM9261)
select SERIAL_CORE
help
This enables the driver for the on-chip UARTs of the Atmel
AT91RM9200 and AT91SAM926 processor.
-config SERIAL_AT91_CONSOLE
- bool "Support for console on AT91RM9200 / AT91SAM9261 serial port"
- depends on SERIAL_AT91=y
+config SERIAL_ATMEL_CONSOLE
+ bool "Support for console on AT91 / AT32 serial port"
+ depends on SERIAL_ATMEL=y
select SERIAL_CORE_CONSOLE
help
Say Y here if you wish to use a UART on the Atmel AT91RM9200 or
which receives all kernel messages and warnings and which allows
logins in single user mode).
-config SERIAL_AT91_TTYAT
+config SERIAL_ATMEL_TTYAT
bool "Install as device ttyAT0-4 instead of ttyS0-4"
- depends on SERIAL_AT91=y
+ depends on SERIAL_ATMEL=y
help
Say Y here if you wish to have the five internal AT91RM9200 UARTs
appear as /dev/ttyAT0-4 (major 204, minor 154-158) instead of the
default y
---help---
Saying Y here will enable the hardware MUX serial driver for
- the Nova and K class systems. The hardware MUX is not 8250/16550
- compatible therefore the /dev/ttyB0 device is shared between the
- Serial MUX and the PDC software console. The following steps
- need to be completed to use the Serial MUX:
+ the Nova, K class systems and D class with a 'remote control card'.
+ The hardware MUX is not 8250/16550 compatible therefore the
+ /dev/ttyB0 device is shared between the Serial MUX and the PDC
+ software console. The following steps need to be completed to use
+ the Serial MUX:
1. create the device entry (mknod /dev/ttyB0 c 11 0)
2. Edit the /etc/inittab to start a getty listening on /dev/ttyB0
select SERIAL_CORE_CONSOLE
config SERIAL_SH_SCI
- tristate "SH SCI(F) serial port support"
+ tristate "SuperH SCI(F) serial port support"
depends on SUPERH || H8300
select SERIAL_CORE
+config SERIAL_SH_SCI_NR_UARTS
+ int "Maximum number of SCI(F) serial ports"
+ depends on SERIAL_SH_SCI
+ default "2"
+
config SERIAL_SH_SCI_CONSOLE
- bool "Support for console on SH SCI(F)"
+ bool "Support for console on SuperH SCI(F)"
depends on SERIAL_SH_SCI=y
select SERIAL_CORE_CONSOLE
depends on M68328 || M68EZ328 || M68VZ328
help
This driver supports the built-in serial port of the Motorola 68328
- (standard, EZ and VZ varities).
+ (standard, EZ and VZ varieties).
config SERIAL_68328_RTS_CTS
bool "Support RTS/CTS on 68328 serial port"