default "4"
help
Set this to the maximum number of serial ports you want
- the kernel to register at boot time. This can be overriden
+ the kernel to register at boot time. This can be overridden
with the module parameter "nr_uarts", or boot-time parameter
8250.nr_uarts
depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
help
Say Y here if you have a Boca serial board. Please read the Boca
- mini-HOWTO, avaialble from <http://www.tldp.org/docs.html#howto>
+ mini-HOWTO, available from <http://www.tldp.org/docs.html#howto>
To compile this driver as a module, choose M here: the module
will be called 8250_boca.
Even if you say Y here, the currently visible framebuffer console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
- "console=ttyAM0". (Try "man bootparam" or see the documentation of
+ "console=ttyAMA0". (Try "man bootparam" or see the documentation of
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
-config SERIAL_AT91
- bool "AT91RM9200 serial port support"
- depends on ARM && ARCH_AT91RM9200
+config SERIAL_ATMEL
+ bool "AT91 / AT32 on-chip serial port support"
+ depends on ARM && (ARCH_AT91RM9200 || ARCH_AT91SAM9261)
select SERIAL_CORE
help
- This enables the driver for the on-chip UARTs of the AT91RM9200
- processor.
+ This enables the driver for the on-chip UARTs of the Atmel
+ AT91RM9200 and AT91SAM926 processor.
-config SERIAL_AT91_CONSOLE
- bool "Support for console on AT91RM9200 serial port"
- depends on SERIAL_AT91=y
+config SERIAL_ATMEL_CONSOLE
+ bool "Support for console on AT91 / AT32 serial port"
+ depends on SERIAL_ATMEL=y
select SERIAL_CORE_CONSOLE
help
- Say Y here if you wish to use a UART on the AT91RM9200 as the system
- console (the system console is the device which receives all kernel
- messages and warnings and which allows logins in single user mode).
+ Say Y here if you wish to use a UART on the Atmel AT91RM9200 or
+ AT91SAM9261 as the system console (the system console is the device
+ which receives all kernel messages and warnings and which allows
+ logins in single user mode).
-config SERIAL_AT91_TTYAT
+config SERIAL_ATMEL_TTYAT
bool "Install as device ttyAT0-4 instead of ttyS0-4"
- depends on SERIAL_AT91=y
+ depends on SERIAL_ATMEL=y
help
Say Y here if you wish to have the five internal AT91RM9200 UARTs
appear as /dev/ttyAT0-4 (major 204, minor 154-158) instead of the
kernel at boot time.)
config SERIAL_S3C2410
- tristate "Samsung S3C2410 Serial port support"
+ tristate "Samsung S3C2410/S3C2440/S3C2442/S3C2412 Serial port support"
depends on ARM && ARCH_S3C2410
select SERIAL_CORE
help
- Support for the on-chip UARTs on the Samsung S3C2410X CPU,
+ Support for the on-chip UARTs on the Samsung S3C24XX series CPUs,
providing /dev/ttySAC0, 1 and 2 (note, some machines may not
provide all of these ports, depending on how the serial port
pins are configured.
+ Currently this driver supports the UARTS on the S3C2410, S3C2440,
+ S3C2442, S3C2412 and S3C2413 CPUs.
+
config SERIAL_S3C2410_CONSOLE
bool "Support for console on S3C2410 serial port"
depends on SERIAL_S3C2410=y
select SERIAL_CORE_CONSOLE
help
- Allow selection of the S3C2410 on-board serial ports for use as
+ Allow selection of the S3C24XX on-board serial ports for use as
an virtual console.
Even if you say Y here, the currently visible virtual console
default y
---help---
Saying Y here will enable the hardware MUX serial driver for
- the Nova and K class systems. The hardware MUX is not 8250/16550
- compatible therefore the /dev/ttyB0 device is shared between the
- Serial MUX and the PDC software console. The following steps
- need to be completed to use the Serial MUX:
+ the Nova, K class systems and D class with a 'remote control card'.
+ The hardware MUX is not 8250/16550 compatible therefore the
+ /dev/ttyB0 device is shared between the Serial MUX and the PDC
+ software console. The following steps need to be completed to use
+ the Serial MUX:
1. create the device entry (mknod /dev/ttyB0 c 11 0)
2. Edit the /etc/inittab to start a getty listening on /dev/ttyB0
select SERIAL_CORE_CONSOLE
config SERIAL_SH_SCI
- tristate "SH SCI(F) serial port support"
+ tristate "SuperH SCI(F) serial port support"
depends on SUPERH || H8300
select SERIAL_CORE
+config SERIAL_SH_SCI_NR_UARTS
+ int "Maximum number of SCI(F) serial ports"
+ depends on SERIAL_SH_SCI
+ default "2"
+
config SERIAL_SH_SCI_CONSOLE
- bool "Support for console on SH SCI(F)"
+ bool "Support for console on SuperH SCI(F)"
depends on SERIAL_SH_SCI=y
select SERIAL_CORE_CONSOLE
depends on M68328 || M68EZ328 || M68VZ328
help
This driver supports the built-in serial port of the Motorola 68328
- (standard, EZ and VZ varities).
+ (standard, EZ and VZ varieties).
config SERIAL_68328_RTS_CTS
bool "Support RTS/CTS on 68328 serial port"
If you have an SGI Altix with an IOC3 serial card,
say Y or M. Otherwise, say N.
+config SERIAL_NETX
+ bool "NetX serial port support"
+ depends on ARM && ARCH_NETX
+ select SERIAL_CORE
+ help
+ If you have a machine based on a Hilscher NetX SoC you
+ can enable its onboard serial port by enabling this option.
+
+ To compile this driver as a module, choose M here: the
+ module will be called netx-serial.
+
+config SERIAL_NETX_CONSOLE
+ bool "Console on NetX serial port"
+ depends on SERIAL_NETX
+ select SERIAL_CORE_CONSOLE
+ help
+ If you have enabled the serial port on the Motorola IMX
+ CPU you can make it the console by answering Y to this option.
+
endmenu
projects / powerpc.git / blobdiff