Merge branches 'at91', 'ep93xx', 'iop', 'kprobes', 'ks8695', 'misc', 'msm', 's3c2410...

[powerpc.git] / drivers / serial / sh-sci.c

diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c
index e4abd3a..73440e2 100644 (file)
--- a/drivers/serial/sh-sci.c
+++ b/drivers/serial/sh-sci.c
@@ -4,6 +4,7 @@
  * SuperH on-chip serial module support.  (SCI with no FIFO / with FIFO)
  *
  *  Copyright (C) 2002 - 2006  Paul Mundt
+ *  Modified to support SH7720 SCIF. Markus Brunner, Mark Jonas (Jul 2007).
  *
  * based off of the old drivers/char/sh-sci.c by:
  *
@@ -301,6 +302,38 @@ static void sci_init_pins_scif(struct uart_port* port, unsigned int cflag)
        }
        sci_out(port, SCFCR, fcr_val);
 }
+#elif defined(CONFIG_CPU_SUBTYPE_SH7720)
+static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
+{
+       unsigned int fcr_val = 0;
+       unsigned short data;
+
+       if (cflag & CRTSCTS) {
+               /* enable RTS/CTS */
+               if (port->mapbase == 0xa4430000) { /* SCIF0 */
+                       /* Clear PTCR bit 9-2; enable all scif pins but sck */
+                       data = ctrl_inw(PORT_PTCR);
+                       ctrl_outw((data & 0xfc03), PORT_PTCR);
+               } else if (port->mapbase == 0xa4438000) { /* SCIF1 */
+                       /* Clear PVCR bit 9-2 */
+                       data = ctrl_inw(PORT_PVCR);
+                       ctrl_outw((data & 0xfc03), PORT_PVCR);
+               }
+               fcr_val |= SCFCR_MCE;
+       } else {
+               if (port->mapbase == 0xa4430000) { /* SCIF0 */
+                       /* Clear PTCR bit 5-2; enable only tx and rx  */
+                       data = ctrl_inw(PORT_PTCR);
+                       ctrl_outw((data & 0xffc3), PORT_PTCR);
+               } else if (port->mapbase == 0xa4438000) { /* SCIF1 */
+                       /* Clear PVCR bit 5-2 */
+                       data = ctrl_inw(PORT_PVCR);
+                       ctrl_outw((data & 0xffc3), PORT_PVCR);
+               }
+       }
+       sci_out(port, SCFCR, fcr_val);
+}
+
 #elif defined(CONFIG_CPU_SH3)
 /* For SH7705, SH7706, SH7707, SH7709, SH7709A, SH7729 */
 static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
@@ -1276,7 +1309,7 @@ static int __init sci_console_init(void)
 console_initcall(sci_console_init);
 #endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */
 
-#ifdef CONFIG_SH_KGDB
+#ifdef CONFIG_SH_KGDB_CONSOLE
 /*
  * FIXME: Most of this can go away.. at the moment, we rely on
  * arch/sh/kernel/setup.c to do the command line parsing for kgdb, though
@@ -1334,9 +1367,7 @@ int __init kgdb_console_setup(struct console *co, char *options)
 
        return uart_set_options(port, co, baud, parity, bits, flow);
 }
-#endif /* CONFIG_SH_KGDB */
 
-#ifdef CONFIG_SH_KGDB_CONSOLE
 static struct console kgdb_console = {
        .name           = "ttySC",
        .device         = uart_console_device,