/*! \file ccspi.c
\author Travis Goodspeed
\brief Chipcon SPI Register Interface
+
+ Unfortunately, there is very little similarity between the CC2420
+ and the CC2500, to name just two of the myriad of Chipcon SPI
+ radios. Auto-detection will be a bit difficult, but more to the
+ point, all high level functionality must be moved into the client.
*/
//Higher level left to client application.
#include "platform.h"
#include "command.h"
-
-#include <signal.h>
-#include <io.h>
-#include <iomacros.h>
+#include <stdlib.h> //added for itoa
#include "ccspi.h"
#include "spi.h"
+//! Handles a Chipcon SPI command.
+void ccspi_handle_fn( uint8_t const app,
+ uint8_t const verb,
+ uint32_t const len);
+
+// define the ccspi app's app_t
+app_t const ccspi_app = {
+
+ /* app number */
+ CCSPI,
+
+ /* handle fn */
+ ccspi_handle_fn,
+
+ /* name */
+ "CCSPI",
-#define RADIOACTIVE SETCE
-#define RADIOPASSIVE CLRCE
+ /* desc */
+ "\tThe CCSPI app adds support for the Chipcon SPI register\n"
+ "\tinterface. Unfortunately, there is very little similarity\n"
+ "\tbetween the CC2420 and the CC2500, to name just two of the\n"
+ "\tmyriad of Chipcon SPI radios. Auto-detection will be a bit\n"
+ "\tdifficult, but more to the point, all high level functionality\n"
+ "\tmust be moved into the client.\n"
+};
//! Set up the pins for CCSPI mode.
void ccspisetup(){
- SETSS;
- P5DIR&=~MISO;
- P5DIR|=MOSI+SCK;
+ SPIDIR&=~MISO;
+ SPIDIR|=MOSI+SCK;
DIRSS;
DIRCE;
-
+
+ P4OUT|=BIT5; //activate CC2420 voltage regulator
+ msdelay(100);
+
+ //Reset the CC2420.
+ P4OUT&=~BIT6;
+ P4OUT|=BIT6;
+
//Begin a new transaction.
- CLRSS;
+ CLRSS;
SETSS;
}
register unsigned int bit;
//This function came from the CCSPI Wikipedia article.
//Minor alterations.
-
+
for (bit = 0; bit < 8; bit++) {
/* write MOSI on trailing edge of previous clock */
if (byte & 0x80)
else
CLRMOSI;
byte <<= 1;
-
+
SETCLK;
-
+
/* read MISO on trailing edge */
byte |= READMISO;
CLRCLK;
}
-
+
return byte;
}
+//! Reflexively jam on the present channel.
+void ccspireflexjam(u16 delay){
+ unsigned long i;
+ #if defined(FIFOP) && defined(SFD) && defined(FIFO) && defined(PLED2DIR) && defined(PLED2PIN) && defined(PLED2OUT)
+
+ prep_timer();
+ debugstr("Reflex jamming until reset.");
+ debughex(delay);
+ txdata(CCSPI,CCSPI_REFLEX,1); //Let the client continue its business.
+ while(1) {
+ //Wait until a packet is received
+ while(!SFD){
+ //Has there been an overflow in the RX buffer?
+ if((!FIFO)&&FIFOP){
+ //debugstr("Clearing RX overflow");
+ CLRSS;
+ ccspitrans8(0x08); //SFLUSHRX
+ SETSS;
+ }
+ }
+ //Turn on LED 2 (green) as signal
+ PLED2DIR |= PLED2PIN;
+ PLED2OUT &= ~PLED2PIN;
+
+
+
+ //Wait a few us to send it.
+ delay_us(delay);
+
+ //Transmit the packet.
+ CLRSS;
+ ccspitrans8(0x04);
+ SETSS;
+
+
+ //Load the next jamming packet.
+ //Note: attempts to preload this actually slowed the jam time down from 7 to 9 bytes.
+ CLRSS;
+ ccspitrans8(CCSPI_TXFIFO);
+ char pkt[5] = {0x05, 0, 0, 0, 0};
+ //char pkt[15] = {0x0f, 0x01, 0x08, 0x82, 0xff, 0xff, 0xff, 0xff, 0xde, 0xad, 0xbe, 0xef, 0xba, 0xbe, 0xc0};
+ //char pkt[12] = {0x0c, 0x01, 0x08, 0x82, 0xff, 0xff, 0xff, 0xff, 0xde, 0xad, 0xbe, 0xef};
+ for(i=0;i<pkt[0];i++)
+ ccspitrans8(pkt[i]);
+ SETSS;
+
+ //* I think this might be unnecessary.
+ //msdelay(100+delay); //Instead of waiting for pulse on SFD
+ //delay_ms(1);
+ //Flush TX buffer.
+ CLRSS;
+ ccspitrans8(0x09); //SFLUSHTX
+ SETSS;
+
+
+ //Turn off LED 2 (green) as signal
+ PLED2DIR |= PLED2PIN;
+ PLED2OUT |= PLED2PIN;
+ }
+#else
+ debugstr("Can't reflexively jam without SFD, FIFO, FIFOP, and P2LEDx definitions - try using telosb platform.");
+ txdata(CCSPI,NOK,0);
+#endif
+}
+
+
+
//! Writes a register
u8 ccspi_regwrite(u8 reg, const u8 *buf, int len){
CLRSS;
-
+
reg=ccspitrans8(reg);
while(len--)
ccspitrans8(*buf++);
-
+
SETSS;
return reg;//status
}
//! Reads a register
u8 ccspi_regread(u8 reg, u8 *buf, int len){
CLRSS;
-
+
reg=ccspitrans8(reg);
while(len--)
*buf++=ccspitrans8(0);
-
+
SETSS;
return reg;//status
}
//! Handles a Chipcon SPI command.
-void ccspihandle(unsigned char app,
- unsigned char verb,
- unsigned long len){
+void ccspi_handle_fn( uint8_t const app,
+ uint8_t const verb,
+ uint32_t const len){
unsigned long i;
-
- //Drop CE to passify radio.
- RADIOPASSIVE;
- //Raise !SS to end transaction, just in case we forgot.
- SETSS;
- ccspisetup();
-
+ u8 j;
+
+ //debugstr("Chipcon SPI handler.");
+
switch(verb){
- //PEEK and POKE might come later.
- case READ:
+ case PEEK:
+ cmddata[0]|=0x40; //Set the read bit.
+ //DO NOT BREAK HERE.
+ case READ:
case WRITE:
+ case POKE:
CLRSS; //Drop !SS to begin transaction.
+ j=cmddata[0];//Backup address.
for(i=0;i<len;i++)
cmddata[i]=ccspitrans8(cmddata[i]);
SETSS; //Raise !SS to end transaction.
- txdata(app,verb,len);
- break;
-
- case PEEK://Grab CCSPI Register
- CLRSS; //Drop !SS to begin transaction.
- ccspitrans8(CCSPI_R_REGISTER | cmddata[0]); //000A AAAA
- for(i=1;i<len;i++)
- cmddata[i]=ccspitrans8(cmddata[i]);
- SETSS; //Raise !SS to end transaction.
- txdata(app,verb,len);
- break;
-
- case POKE://Poke CCSPI Register
- CLRSS; //Drop !SS to begin transaction.
- ccspitrans8(CCSPI_W_REGISTER | cmddata[0]); //001A AAAA
- for(i=1;i<len;i++)
- cmddata[i]=ccspitrans8(cmddata[i]);
- SETSS; //Raise !SS to end transaction.
+ cmddata[0]=j&~0x40;//Restore address.
txdata(app,verb,len);
break;
case SETUP:
txdata(app,verb,0);
break;
case CCSPI_RX:
- RADIOPASSIVE;
- //Get the packet.
- CLRSS;
- ccspitrans8(CCSPI_RXFIFO);
- for(i=0;i<32;i++)
- cmddata[i]=ccspitrans8(0xde);
- SETSS;
- //no break
- txdata(app,verb,32);
+#ifdef FIFOP
+ //Has there been an overflow?
+ if((!FIFO)&&FIFOP){
+ //debugstr("Clearing overflow");
+ CLRSS;
+ ccspitrans8(0x08); //SFLUSHRX
+ SETSS;
+ }
+
+ //Is there a packet?
+ if(FIFOP&&FIFO){
+ //Wait for completion.
+ while(SFD);
+
+ //Get the packet.
+ CLRSS;
+ ccspitrans8(CCSPI_RXFIFO | 0x40);
+ //ccspitrans8(0x3F|0x40);
+ cmddata[0]=0xff; //to be replaced with length
+ for(i=0;i<cmddata[0]+2;i++)
+ cmddata[i]=ccspitrans8(0xde);
+ SETSS;
+
+ //Flush buffer.
+ CLRSS;
+ ccspitrans8(0x08); //SFLUSHRX
+ SETSS;
+
+
+ //Only should transmit length of one more than the reported
+ // length of the frame, which holds the length byte:
+ txdata(app,verb,cmddata[0]+1);
+ }else{
+ //No packet.
+ txdata(app,verb,0);
+ }
+#else
+ debugstr("Can't RX a packet with SFD and FIFOP definitions.");
+ txdata(app,NOK,0);
+#endif
break;
case CCSPI_RX_FLUSH:
//Flush the buffer.
CLRSS;
ccspitrans8(CCSPI_SFLUSHRX);
SETSS;
-
- //Return the packet.
- txdata(app,verb,32);
+
+ txdata(app,verb,0);
break;
- case CCSPI_TX:
+
+ case CCSPI_REFLEX:
+ ccspireflexjam(len?cmddataword[0]:0);
+ break;
+
+ case CCSPI_REFLEX_AUTOACK:
+#if defined(FIFOP) && defined(SFD) && defined(FIFO) && defined(PLED2DIR) && defined(PLED2PIN) && defined(PLED2OUT)
+ //txdata(app, verb, 1);
+ debugstr("AutoACK");
+ char byte[4];
+ while(1) {
+ //Has there been an overflow in the RX buffer?
+ if((!FIFO)&&FIFOP){
+ //debugstr("Clearing overflow");
+ CLRSS;
+ ccspitrans8(0x08); //SFLUSHRX
+ SETSS;
+ }
+
+ //Wait until a packet is received
+ while(!SFD);
+ //Turn on LED 2 (green) as signal
+ PLED2DIR |= PLED2PIN;
+ PLED2OUT &= ~PLED2PIN;
+
+ //Put radio in TX mode
+ //Note: Not doing this slows down jamming, so can't jam short packets.
+ // However, if we do this, it seems to mess up our RXFIFO ability.
+ //CLRSS;
+ //ccspitrans8(0x04);
+ //SETSS;
+ //Load the jamming packet
+ CLRSS;
+ ccspitrans8(CCSPI_TXFIFO);
+ char pkt[7] = {0x07, 0x01, 0x08, 0xff, 0xff, 0xff, 0xff};
+ for(i=0;i<pkt[0];i++)
+ ccspitrans8(pkt[i]);
+ SETSS;
+ //Transmit the jamming packet
+ CLRSS;
+ ccspitrans8(0x04); //STXON
+ SETSS;
+ msdelay(200); //Instead of examining SFD line status
+ //Flush TX buffer.
+ CLRSS;
+ ccspitrans8(0x09); //SFLUSHTX
+ SETSS;
+
+ //Get the orignally received packet, up to the seqnum field.
+ CLRSS;
+ ccspitrans8(CCSPI_RXFIFO | 0x40);
+ for(i=0;i<4;i++)
+ cmddata[i]=ccspitrans8(0xde);
+ SETSS;
+ //Flush RX buffer.
+ CLRSS;
+ ccspitrans8(0x08); //SFLUSHRX
+ SETSS;
+ //Send the sequence number of the jammed packet back to the client
+ //itoa(cmddata[3], byte, 16);
+ //debugstr(byte);
+ //txdata(app,verb,cmddata[3]);
+
+ //TODO turn on AUTOCRC for it to apply to the TX???
+ // this may overcome issues of bad crc / length issues?
+ //mdmctrl0 (0x11) register set bit 5 to true.
+
+ //Create the forged ACK packet
+ cmddata[0] = 6; //length of ack frame plus length
+ cmddata[1] = 0x02; //first byte of FCF
+ cmddata[2] = 0x00; //second byte of FCF
+ //[3] is already filled with the sequence number
+ int crc = 0;
+ for(i=1;i<4;i++) {
+ int c = cmddata[i];
+ int q = (crc ^ c) & 15; //Do low-order 4 bits
+ crc = (crc / 16) ^ (q * 4225);
+ q = (crc ^ (c / 16)) & 15; //And high 4 bits
+ crc = (crc / 16) ^ (q * 4225);
+ }
+ cmddata[4] = crc & 0xFF;
+ cmddata[5] = (crc >> 8) & 0xFF;
+
+ for(i=0;i<cmddata[0];i++) {
+ itoa(cmddata[i], byte, 16);
+ debugstr(byte);
+ }
+ //Load the forged ACK packet
+ CLRSS;
+ ccspitrans8(CCSPI_TXFIFO);
+ for(i=0;i<cmddata[0];i++)
+ ccspitrans8(cmddata[i]);
+ SETSS;
+ //Transmit the forged ACK packet
+ while(SFD);
+ CLRSS;
+ ccspitrans8(0x04); //STXON
+ SETSS;
+ msdelay(200); //TODO try doing this based on SFD line status instead
+ //Flush TX buffer
+ CLRSS;
+ ccspitrans8(0x09); //SFLUSHTX
+ SETSS;
+
+ //TODO disable AUTOCRC here again to go back to promiscous mode
+
+ //Turn off LED 2 (green) as signal
+ PLED2DIR |= PLED2PIN;
+ PLED2OUT |= PLED2PIN;
+ }
+ //TODO the firmware stops staying in this mode after a while, and stops jamming... need to find a fix.
+#else
+ debugstr("Can't reflexively jam without SFD, FIFO, FIFOP, and P2LEDx definitions - try using telosb platform.");
+ txdata(app,NOK,0);
+#endif
+ break;
+
case CCSPI_TX_FLUSH:
+ //Flush the buffer.
+ CLRSS;
+ ccspitrans8(CCSPI_SFLUSHTX);
+ SETSS;
+
+ txdata(app,verb,0);
+ break;
+ case CCSPI_TX:
+#ifdef FIFOP
+
+ //Wait for last packet to TX.
+ //while(ccspi_status()&BIT3);
+
+ //Flush TX buffer.
+ CLRSS;
+ ccspitrans8(0x09); //SFLUSHTX
+ SETSS;
+
+
+ //Load the packet.
+ CLRSS;
+ ccspitrans8(CCSPI_TXFIFO);
+ for(i=0;i<cmddata[0];i++)
+ ccspitrans8(cmddata[i]);
+ SETSS;
+
+ //Transmit the packet.
+ CLRSS;
+ ccspitrans8(0x04); //STXON
+ SETSS;
+
+ //Wait for the pulse on SFD, after which the packet has been sent.
+ while(!SFD);
+ while(SFD);
+
+ txdata(app,verb,0);
+#else
+ debugstr("Can't TX a packet with SFD and FIFOP definitions.");
+ txdata(app,NOK,0);
+#endif
+ break;
default:
- debugstr("Not yet supported.");
+ debugstr("Not yet supported in CCSPI");
txdata(app,verb,0);
break;
}
-
- SETSS;//End session
- RADIOACTIVE;
}