X-Git-Url: http://git.rot13.org/?a=blobdiff_plain;f=drivers%2Fata%2Fpata_mpiix.c;h=3bfbd495f6434425e6d5cdb2b82c7618e6c9ce27;hb=48be6b18336567a795bc41e4526f9adfb3a3d68e;hp=9dfe3e9abea31bf21d2d63136d54247d4bee52a5;hpb=97d41e90fe61399b99d74820cb7f2d6e0fbac91d;p=powerpc.git diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c index 9dfe3e9abe..3bfbd495f6 100644 --- a/drivers/ata/pata_mpiix.c +++ b/drivers/ata/pata_mpiix.c @@ -35,7 +35,7 @@ #include #define DRV_NAME "pata_mpiix" -#define DRV_VERSION "0.7.2" +#define DRV_VERSION "0.7.6" enum { IDETIM = 0x6C, /* IDE control register */ @@ -46,18 +46,15 @@ enum { SECONDARY = (1 << 14) }; -static int mpiix_pre_reset(struct ata_port *ap) +static int mpiix_pre_reset(struct ata_port *ap, unsigned long deadline) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); - static const struct pci_bits mpiix_enable_bits[] = { - { 0x6D, 1, 0x80, 0x80 }, - { 0x6F, 1, 0x80, 0x80 } - }; + static const struct pci_bits mpiix_enable_bits = { 0x6D, 1, 0x80, 0x80 }; - if (!pci_test_config_bits(pdev, &mpiix_enable_bits[ap->port_no])) + if (!pci_test_config_bits(pdev, &mpiix_enable_bits)) return -ENOENT; - ap->cbl = ATA_CBL_PATA40; - return ata_std_prereset(ap); + + return ata_std_prereset(ap, deadline); } /** @@ -80,8 +77,8 @@ static void mpiix_error_handler(struct ata_port *ap) * @adev: ATA device * * Called to do the PIO mode setup. The MPIIX allows us to program the - * IORDY sample point (2-5 clocks), recovery 1-4 clocks and whether - * prefetching or iordy are used. + * IORDY sample point (2-5 clocks), recovery (1-4 clocks) and whether + * prefetching or IORDY are used. * * This would get very ugly because we can only program timing for one * device at a time, the other gets PIO0. Fortunately libata calls @@ -103,18 +100,19 @@ static void mpiix_set_piomode(struct ata_port *ap, struct ata_device *adev) { 2, 3 }, }; pci_read_config_word(pdev, IDETIM, &idetim); - /* Mask the IORDY/TIME/PPE0 bank for this device */ + + /* Mask the IORDY/TIME/PPE for this device */ if (adev->class == ATA_DEV_ATA) - control |= PPE; /* PPE enable for disk */ + control |= PPE; /* Enable prefetch/posting for disk */ if (ata_pio_need_iordy(adev)) - control |= IORDY; /* IORDY */ - if (pio > 0) + control |= IORDY; + if (pio > 1) control |= FTIM; /* This drive is on the fast timing bank */ /* Mask out timing and clear both TIME bank selects */ idetim &= 0xCCEE; - idetim &= ~(0x07 << (2 * adev->devno)); - idetim |= (control << (2 * adev->devno)); + idetim &= ~(0x07 << (4 * adev->devno)); + idetim |= control << (4 * adev->devno); idetim |= (timings[pio][0] << 12) | (timings[pio][1] << 8); pci_write_config_word(pdev, IDETIM, idetim); @@ -159,14 +157,18 @@ static struct scsi_host_template mpiix_sht = { .can_queue = ATA_DEF_QUEUE, .this_id = ATA_SHT_THIS_ID, .sg_tablesize = LIBATA_MAX_PRD, - .max_sectors = ATA_MAX_SECTORS, .cmd_per_lun = ATA_SHT_CMD_PER_LUN, .emulated = ATA_SHT_EMULATED, .use_clustering = ATA_SHT_USE_CLUSTERING, .proc_name = DRV_NAME, .dma_boundary = ATA_DMA_BOUNDARY, .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, .bios_param = ata_std_bios_param, +#ifdef CONFIG_PM + .resume = ata_scsi_device_resume, + .suspend = ata_scsi_device_suspend, +#endif }; static struct ata_port_operations mpiix_port_ops = { @@ -183,30 +185,36 @@ static struct ata_port_operations mpiix_port_ops = { .thaw = ata_bmdma_thaw, .error_handler = mpiix_error_handler, .post_internal_cmd = ata_bmdma_post_internal_cmd, + .cable_detect = ata_cable_40wire, .qc_prep = ata_qc_prep, .qc_issue = mpiix_qc_issue_prot, - .data_xfer = ata_pio_data_xfer, + .data_xfer = ata_data_xfer, - .irq_handler = ata_interrupt, .irq_clear = ata_bmdma_irq_clear, + .irq_on = ata_irq_on, + .irq_ack = ata_irq_ack, .port_start = ata_port_start, - .port_stop = ata_port_stop, - .host_stop = ata_host_stop }; static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id) { /* Single threaded by the PCI probe logic */ - static struct ata_probe_ent probe[2]; static int printed_version; + struct ata_host *host; + struct ata_port *ap; + void __iomem *cmd_addr, *ctl_addr; u16 idetim; - int enabled; + int irq; if (!printed_version++) dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n"); + host = ata_host_alloc(&dev->dev, 1); + if (!host) + return -ENOMEM; + /* MPIIX has many functions which can be turned on or off according to other devices present. Make sure IDE is enabled before we try and use it */ @@ -215,63 +223,41 @@ static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id) if (!(idetim & ENABLED)) return -ENODEV; + /* See if it's primary or secondary channel... */ + if (!(idetim & SECONDARY)) { + irq = 14; + cmd_addr = devm_ioport_map(&dev->dev, 0x1F0, 8); + ctl_addr = devm_ioport_map(&dev->dev, 0x3F6, 1); + } else { + irq = 15; + cmd_addr = devm_ioport_map(&dev->dev, 0x170, 8); + ctl_addr = devm_ioport_map(&dev->dev, 0x376, 1); + } + + if (!cmd_addr || !ctl_addr) + return -ENOMEM; + /* We do our own plumbing to avoid leaking special cases for whacko ancient hardware into the core code. There are two issues to worry about. #1 The chip is a bridge so if in legacy mode and without BARs set fools the setup. #2 If you pci_disable_device the MPIIX your box goes castors up */ - INIT_LIST_HEAD(&probe[0].node); - probe[0].dev = pci_dev_to_dev(dev); - probe[0].port_ops = &mpiix_port_ops; - probe[0].sht = &mpiix_sht; - probe[0].pio_mask = 0x1F; - probe[0].irq = 14; - probe[0].irq_flags = SA_SHIRQ; - probe[0].port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST; - probe[0].n_ports = 1; - probe[0].port[0].cmd_addr = 0x1F0; - probe[0].port[0].ctl_addr = 0x3F6; - probe[0].port[0].altstatus_addr = 0x3F6; - - /* The secondary lurks at different addresses but is otherwise - the same beastie */ - - INIT_LIST_HEAD(&probe[1].node); - probe[1] = probe[0]; - probe[1].irq = 15; - probe[1].port[0].cmd_addr = 0x170; - probe[1].port[0].ctl_addr = 0x376; - probe[1].port[0].altstatus_addr = 0x376; - - /* Let libata fill in the port details */ - ata_std_ports(&probe[0].port[0]); - ata_std_ports(&probe[1].port[0]); + ap = host->ports[0]; + ap->ops = &mpiix_port_ops; + ap->pio_mask = 0x1F; + ap->flags |= ATA_FLAG_SLAVE_POSS; - /* Now add the port that is active */ - enabled = (idetim & SECONDARY) ? 1 : 0; + ap->ioaddr.cmd_addr = cmd_addr; + ap->ioaddr.ctl_addr = ctl_addr; + ap->ioaddr.altstatus_addr = ctl_addr; - if (ata_device_add(&probe[enabled])) - return 0; - return -ENODEV; -} - -/** - * mpiix_remove_one - device unload - * @pdev: PCI device being removed - * - * Handle an unplug/unload event for a PCI device. Unload the - * PCI driver but do not use the default handler as we *MUST NOT* - * disable the device as it has other functions. - */ - -static void __devexit mpiix_remove_one(struct pci_dev *pdev) -{ - struct device *dev = pci_dev_to_dev(pdev); - struct ata_host *host = dev_get_drvdata(dev); + /* Let libata fill in the port details */ + ata_std_ports(&ap->ioaddr); - ata_host_remove(host); - dev_set_drvdata(dev, NULL); + /* activate host */ + return ata_host_activate(host, irq, ata_interrupt, IRQF_SHARED, + &mpiix_sht); } static const struct pci_device_id mpiix[] = { @@ -284,7 +270,11 @@ static struct pci_driver mpiix_pci_driver = { .name = DRV_NAME, .id_table = mpiix, .probe = mpiix_init_one, - .remove = mpiix_remove_one + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM + .suspend = ata_pci_device_suspend, + .resume = ata_pci_device_resume, +#endif }; static int __init mpiix_init(void)