X-Git-Url: http://git.rot13.org/?a=blobdiff_plain;f=drivers%2Fata%2Fpata_sl82c105.c;h=9aeffdbe28293e72df734f5c0b72953f9051cdf1;hb=d4b2bab4f26345ea1803feb23ea92fbe3f6b77bc;hp=96e890fd645b671247069881385de1c36d0abdb0;hpb=9654640d0af8f2de40ff3807d3695109d3463f54;p=powerpc.git

diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index 96e890fd64..9aeffdbe28 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -7,6 +7,13 @@
  * 		SL82C105/Winbond 553 IDE driver
  *
  * and in part on the documentation and errata sheet
+ *
+ *
+ * Note: The controller like many controllers has shared timings for
+ * PIO and DMA. We thus flip to the DMA timings in dma_start and flip back
+ * in the dma_stop function. Thus we actually don't need a set_dmamode
+ * method as the PIO method is always called and will set the right PIO
+ * timing parameters.
  */
 
 #include <linux/kernel.h>
@@ -19,7 +26,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_sl82c105"
-#define DRV_VERSION "0.2.3"
+#define DRV_VERSION "0.3.0"
 
 enum {
 	/*
@@ -37,11 +44,12 @@ enum {
 /**
  *	sl82c105_pre_reset		-	probe begin
  *	@ap: ATA port
+ *	@deadline: deadline jiffies for the operation
  *
  *	Set up cable type and use generic probe init
  */
 
-static int sl82c105_pre_reset(struct ata_port *ap)
+static int sl82c105_pre_reset(struct ata_port *ap, unsigned long deadline)
 {
 	static const struct pci_bits sl82c105_enable_bits[] = {
 		{ 0x40, 1, 0x01, 0x01 },
@@ -51,8 +59,7 @@ static int sl82c105_pre_reset(struct ata_port *ap)
 
 	if (ap->port_no && !pci_test_config_bits(pdev, &sl82c105_enable_bits[ap->port_no]))
 		return -ENOENT;
-	ap->cbl = ATA_CBL_PATA40;
-	return ata_std_prereset(ap);
+	return ata_std_prereset(ap, deadline);
 }
 
 
@@ -125,33 +132,6 @@ static void sl82c105_configure_dmamode(struct ata_port *ap, struct ata_device *a
 	pci_read_config_word(pdev, timing, &dummy);
 }
 
-/**
- *	sl82c105_set_dmamode	-	set initial DMA mode data
- *	@ap: ATA interface
- *	@adev: ATA device
- *
- *	Called to do the DMA mode setup. This replaces the PIO timings
- *	for the device in question. Set appropriate PIO timings not DMA
- *	timings at this point.
- */
-
-static void sl82c105_set_dmamode(struct ata_port *ap, struct ata_device *adev)
-{
-	switch(adev->dma_mode) {
-		case XFER_MW_DMA_0:
-			sl82c105_configure_piomode(ap, adev, 0);
-			break;
-		case XFER_MW_DMA_1:
-			sl82c105_configure_piomode(ap, adev, 3);
-			break;
-		case XFER_MW_DMA_2:
-			sl82c105_configure_piomode(ap, adev, 4);
-			break;
-		default:
-			BUG();
-	}
-}
-
 /**
  *	sl82c105_reset_engine	-	Reset the DMA engine
  *	@ap: ATA interface
@@ -222,7 +202,7 @@ static void sl82c105_bmdma_stop(struct ata_queued_cmd *qc)
 
 	/* This will redo the initial setup of the DMA device to matching
 	   PIO timings */
-	sl82c105_set_dmamode(ap, qc->dev);
+	sl82c105_set_piomode(ap, qc->dev);
 }
 
 static struct scsi_host_template sl82c105_sht = {
@@ -246,7 +226,6 @@ static struct scsi_host_template sl82c105_sht = {
 static struct ata_port_operations sl82c105_port_ops = {
 	.port_disable	= ata_port_disable,
 	.set_piomode	= sl82c105_set_piomode,
-	.set_dmamode	= sl82c105_set_dmamode,
 	.mode_filter	= ata_pci_default_filter,
 
 	.tf_load	= ata_tf_load,
@@ -255,7 +234,11 @@ static struct ata_port_operations sl82c105_port_ops = {
 	.exec_command	= ata_exec_command,
 	.dev_select 	= ata_std_dev_select,
 
+	.freeze		= ata_bmdma_freeze,
+	.thaw		= ata_bmdma_thaw,
 	.error_handler	= sl82c105_error_handler,
+	.post_internal_cmd = ata_bmdma_post_internal_cmd,
+	.cable_detect	= ata_cable_40wire,
 
 	.bmdma_setup 	= ata_bmdma_setup,
 	.bmdma_start 	= sl82c105_bmdma_start,