X-Git-Url: http://git.rot13.org/?a=blobdiff_plain;f=drivers%2Fhwmon%2Fabituguru.c;h=bede4d990ea67330546e7b897ae51bf434f55341;hb=459e536b1ddfd217ec8a3437a3214968a98223c7;hp=cc15c4f2e9ecd28595e5f80c4bc5712e46d7f817;hpb=0d10e47f9635ecafe5a9dc6e10cb056a87a4daa2;p=powerpc.git diff --git a/drivers/hwmon/abituguru.c b/drivers/hwmon/abituguru.c index cc15c4f2e9..bede4d990e 100644 --- a/drivers/hwmon/abituguru.c +++ b/drivers/hwmon/abituguru.c @@ -21,11 +21,13 @@ etc voltage & frequency control is not supported! */ #include +#include #include #include #include #include #include +#include #include #include #include @@ -64,17 +66,17 @@ #define ABIT_UGURU_IN_SENSOR 0 #define ABIT_UGURU_TEMP_SENSOR 1 #define ABIT_UGURU_NC 2 -/* Timeouts / Retries, if these turn out to need a lot of fiddling we could - convert them to params. */ -/* 250 was determined by trial and error, 200 works most of the time, but not - always. I assume this is cpu-speed independent, since the ISA-bus and not - the CPU should be the bottleneck. Note that 250 sometimes is still not - enough (only reported on AN7 mb) this is handled by a higher layer. */ -#define ABIT_UGURU_WAIT_TIMEOUT 250 +/* In many cases we need to wait for the uGuru to reach a certain status, most + of the time it will reach this status within 30 - 90 ISA reads, and thus we + can best busy wait. This define gives the total amount of reads to try. */ +#define ABIT_UGURU_WAIT_TIMEOUT 125 +/* However sometimes older versions of the uGuru seem to be distracted and they + do not respond for a long time. To handle this we sleep before each of the + last ABIT_UGURU_WAIT_TIMEOUT_SLEEP tries. */ +#define ABIT_UGURU_WAIT_TIMEOUT_SLEEP 5 /* Normally all expected status in abituguru_ready, are reported after the - first read, but sometimes not and we need to poll, 5 polls was not enough - 50 sofar is. */ -#define ABIT_UGURU_READY_TIMEOUT 50 + first read, but sometimes not and we need to poll. */ +#define ABIT_UGURU_READY_TIMEOUT 5 /* Maximum 3 retries on timedout reads/writes, delay 200 ms before retrying */ #define ABIT_UGURU_MAX_RETRIES 3 #define ABIT_UGURU_RETRY_DELAY (HZ/5) @@ -226,6 +228,10 @@ static int abituguru_wait(struct abituguru_data *data, u8 state) timeout--; if (timeout == 0) return -EBUSY; + /* sleep a bit before our last few tries, see the comment on + this where ABIT_UGURU_WAIT_TIMEOUT_SLEEP is defined. */ + if (timeout <= ABIT_UGURU_WAIT_TIMEOUT_SLEEP) + msleep(0); } return 0; } @@ -256,6 +262,7 @@ static int abituguru_ready(struct abituguru_data *data) "CMD reg does not hold 0xAC after ready command\n"); return -EIO; } + msleep(0); } /* After this the ABIT_UGURU_DATA port should contain @@ -268,6 +275,7 @@ static int abituguru_ready(struct abituguru_data *data) "state != more input after ready command\n"); return -EIO; } + msleep(0); } data->uguru_ready = 1; @@ -331,7 +339,8 @@ static int abituguru_read(struct abituguru_data *data, /* And read the data */ for (i = 0; i < count; i++) { if (abituguru_wait(data, ABIT_UGURU_STATUS_READ)) { - ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for " + ABIT_UGURU_DEBUG(retries ? 1 : 3, + "timeout exceeded waiting for " "read state (bank: %d, sensor: %d)\n", (int)bank_addr, (int)sensor_addr); break; @@ -350,7 +359,9 @@ static int abituguru_read(struct abituguru_data *data, static int abituguru_write(struct abituguru_data *data, u8 bank_addr, u8 sensor_addr, u8 *buf, int count) { - int i; + /* We use the ready timeout as we have to wait for 0xAC just like the + ready function */ + int i, timeout = ABIT_UGURU_READY_TIMEOUT; /* Send the address */ i = abituguru_send_address(data, bank_addr, sensor_addr, @@ -370,7 +381,8 @@ static int abituguru_write(struct abituguru_data *data, } /* Now we need to wait till the chip is ready to be read again, - don't ask why */ + so that we can read 0xAC as confirmation that our write has + succeeded. */ if (abituguru_wait(data, ABIT_UGURU_STATUS_READ)) { ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for read state " "after write (bank: %d, sensor: %d)\n", (int)bank_addr, @@ -379,11 +391,15 @@ static int abituguru_write(struct abituguru_data *data, } /* Cmd port MUST be read now and should contain 0xAC */ - if (inb_p(data->addr + ABIT_UGURU_CMD) != 0xAC) { - ABIT_UGURU_DEBUG(1, "CMD reg does not hold 0xAC after write " - "(bank: %d, sensor: %d)\n", (int)bank_addr, - (int)sensor_addr); - return -EIO; + while (inb_p(data->addr + ABIT_UGURU_CMD) != 0xAC) { + timeout--; + if (timeout == 0) { + ABIT_UGURU_DEBUG(1, "CMD reg does not hold 0xAC after " + "write (bank: %d, sensor: %d)\n", + (int)bank_addr, (int)sensor_addr); + return -EIO; + } + msleep(0); } /* Last put the chip back in ready state */ @@ -403,7 +419,7 @@ abituguru_detect_bank1_sensor_type(struct abituguru_data *data, u8 sensor_addr) { u8 val, buf[3]; - int ret = ABIT_UGURU_NC; + int i, ret = -ENODEV; /* error is the most common used retval :| */ /* If overriden by the user return the user selected type */ if (bank1_types[sensor_addr] >= ABIT_UGURU_IN_SENSOR && @@ -439,7 +455,7 @@ abituguru_detect_bank1_sensor_type(struct abituguru_data *data, buf[2] = 250; if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr, buf, 3) != 3) - return -ENODEV; + goto abituguru_detect_bank1_sensor_type_exit; /* Now we need 20 ms to give the uguru time to read the sensors and raise a voltage alarm */ set_current_state(TASK_UNINTERRUPTIBLE); @@ -447,21 +463,16 @@ abituguru_detect_bank1_sensor_type(struct abituguru_data *data, /* Check for alarm and check the alarm is a volt low alarm. */ if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0, buf, 3, ABIT_UGURU_MAX_RETRIES) != 3) - return -ENODEV; + goto abituguru_detect_bank1_sensor_type_exit; if (buf[sensor_addr/8] & (0x01 << (sensor_addr % 8))) { if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1, sensor_addr, buf, 3, ABIT_UGURU_MAX_RETRIES) != 3) - return -ENODEV; + goto abituguru_detect_bank1_sensor_type_exit; if (buf[0] & ABIT_UGURU_VOLT_LOW_ALARM_FLAG) { - /* Restore original settings */ - if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, - sensor_addr, - data->bank1_settings[sensor_addr], - 3) != 3) - return -ENODEV; ABIT_UGURU_DEBUG(2, " found volt sensor\n"); - return ABIT_UGURU_IN_SENSOR; + ret = ABIT_UGURU_IN_SENSOR; + goto abituguru_detect_bank1_sensor_type_exit; } else ABIT_UGURU_DEBUG(2, " alarm raised during volt " "sensor test, but volt low flag not set\n"); @@ -477,7 +488,7 @@ abituguru_detect_bank1_sensor_type(struct abituguru_data *data, buf[2] = 10; if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr, buf, 3) != 3) - return -ENODEV; + goto abituguru_detect_bank1_sensor_type_exit; /* Now we need 50 ms to give the uguru time to read the sensors and raise a temp alarm */ set_current_state(TASK_UNINTERRUPTIBLE); @@ -485,15 +496,16 @@ abituguru_detect_bank1_sensor_type(struct abituguru_data *data, /* Check for alarm and check the alarm is a temp high alarm. */ if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0, buf, 3, ABIT_UGURU_MAX_RETRIES) != 3) - return -ENODEV; + goto abituguru_detect_bank1_sensor_type_exit; if (buf[sensor_addr/8] & (0x01 << (sensor_addr % 8))) { if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1, sensor_addr, buf, 3, ABIT_UGURU_MAX_RETRIES) != 3) - return -ENODEV; + goto abituguru_detect_bank1_sensor_type_exit; if (buf[0] & ABIT_UGURU_TEMP_HIGH_ALARM_FLAG) { - ret = ABIT_UGURU_TEMP_SENSOR; ABIT_UGURU_DEBUG(2, " found temp sensor\n"); + ret = ABIT_UGURU_TEMP_SENSOR; + goto abituguru_detect_bank1_sensor_type_exit; } else ABIT_UGURU_DEBUG(2, " alarm raised during temp " "sensor test, but temp high flag not set\n"); @@ -501,11 +513,23 @@ abituguru_detect_bank1_sensor_type(struct abituguru_data *data, ABIT_UGURU_DEBUG(2, " alarm not raised during temp sensor " "test\n"); - /* Restore original settings */ - if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr, - data->bank1_settings[sensor_addr], 3) != 3) + ret = ABIT_UGURU_NC; +abituguru_detect_bank1_sensor_type_exit: + /* Restore original settings, failing here is really BAD, it has been + reported that some BIOS-es hang when entering the uGuru menu with + invalid settings present in the uGuru, so we try this 3 times. */ + for (i = 0; i < 3; i++) + if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, + sensor_addr, data->bank1_settings[sensor_addr], + 3) == 3) + break; + if (i == 3) { + printk(KERN_ERR ABIT_UGURU_NAME + ": Fatal error could not restore original settings. " + "This should never happen please report this to the " + "abituguru maintainer (see MAINTAINERS)\n"); return -ENODEV; - + } return ret; } @@ -1243,30 +1267,42 @@ static int __devinit abituguru_probe(struct platform_device *pdev) printk(KERN_INFO ABIT_UGURU_NAME ": found Abit uGuru\n"); /* Register sysfs hooks */ - data->class_dev = hwmon_device_register(&pdev->dev); - if (IS_ERR(data->class_dev)) { - res = PTR_ERR(data->class_dev); - goto abituguru_probe_error; - } for (i = 0; i < sysfs_attr_i; i++) - device_create_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); + if (device_create_file(&pdev->dev, + &data->sysfs_attr[i].dev_attr)) + goto abituguru_probe_error; for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++) - device_create_file(&pdev->dev, - &abituguru_sysfs_attr[i].dev_attr); + if (device_create_file(&pdev->dev, + &abituguru_sysfs_attr[i].dev_attr)) + goto abituguru_probe_error; - return 0; + data->class_dev = hwmon_device_register(&pdev->dev); + if (!IS_ERR(data->class_dev)) + return 0; /* success */ + res = PTR_ERR(data->class_dev); abituguru_probe_error: + for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++) + device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); + for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++) + device_remove_file(&pdev->dev, + &abituguru_sysfs_attr[i].dev_attr); kfree(data); return res; } static int __devexit abituguru_remove(struct platform_device *pdev) { + int i; struct abituguru_data *data = platform_get_drvdata(pdev); platform_set_drvdata(pdev, NULL); hwmon_device_unregister(data->class_dev); + for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++) + device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); + for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++) + device_remove_file(&pdev->dev, + &abituguru_sysfs_attr[i].dev_attr); kfree(data); return 0; @@ -1305,7 +1341,7 @@ static struct abituguru_data *abituguru_update_device(struct device *dev) data->update_timeouts = 0; LEAVE_UPDATE: /* handle timeout condition */ - if (err == -EBUSY) { + if (!success && (err == -EBUSY || err >= 0)) { /* No overflow please */ if (data->update_timeouts < 255u) data->update_timeouts++; @@ -1331,13 +1367,39 @@ LEAVE_UPDATE: return NULL; } +#ifdef CONFIG_PM +static int abituguru_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct abituguru_data *data = platform_get_drvdata(pdev); + /* make sure all communications with the uguru are done and no new + ones are started */ + mutex_lock(&data->update_lock); + return 0; +} + +static int abituguru_resume(struct platform_device *pdev) +{ + struct abituguru_data *data = platform_get_drvdata(pdev); + /* See if the uGuru is still ready */ + if (inb_p(data->addr + ABIT_UGURU_DATA) != ABIT_UGURU_STATUS_INPUT) + data->uguru_ready = 0; + mutex_unlock(&data->update_lock); + return 0; +} +#else +#define abituguru_suspend NULL +#define abituguru_resume NULL +#endif /* CONFIG_PM */ + static struct platform_driver abituguru_driver = { .driver = { .owner = THIS_MODULE, .name = ABIT_UGURU_NAME, }, - .probe = abituguru_probe, - .remove = __devexit_p(abituguru_remove), + .probe = abituguru_probe, + .remove = __devexit_p(abituguru_remove), + .suspend = abituguru_suspend, + .resume = abituguru_resume, }; static int __init abituguru_detect(void)