X-Git-Url: http://git.rot13.org/?a=blobdiff_plain;f=drivers%2Fvideo%2FKconfig;h=758435f8a6f8cb32f4e7413ad0eeafa7d4b74239;hb=2b3b3516b6eeea1464e205b2dde9ebc9b7dd2ec8;hp=b3bf4ecc983a83969559128b47626472cfd980ba;hpb=c2f73fd07d2ce4605b404f34395eb734a7ba9967;p=powerpc.git

diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index b3bf4ecc98..758435f8a6 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -503,7 +503,7 @@ config FB_VALKYRIE
 
 config FB_CT65550
 	bool "Chips 65550 display support"
-	depends on (FB = y) && PPC32
+	depends on (FB = y) && PPC32 && PCI
 	select FB_CFB_FILLRECT
 	select FB_CFB_COPYAREA
 	select FB_CFB_IMAGEBLIT
@@ -641,6 +641,17 @@ config FB_VESA
 	  You will get a boot time penguin logo at no additional cost. Please
 	  read <file:Documentation/fb/vesafb.txt>. If unsure, say Y.
 
+config FB_EFI
+	bool "EFI-based Framebuffer Support"
+	depends on (FB = y) && X86
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the EFI frame buffer device driver. If the firmware on
+	  your platform is UEFI2.0, select Y to add support for
+	  Graphics Output Protocol for early console messages to appear.
+
 config FB_IMAC
 	bool "Intel-based Macintosh Framebuffer Support"
 	depends on (FB = y) && X86 && EFI
@@ -661,7 +672,7 @@ config FB_HECUBA
        help
          This enables support for the Hecuba board. This driver was tested
          with an E-Ink 800x600 display and x86 SBCs through a 16 bit GPIO
-         interface (8 bit data, 4 bit control). If you anticpate using
+         interface (8 bit data, 4 bit control). If you anticipate using
          this driver, say Y or M; otherwise say N. You must specify the
          GPIO IO address to be used for setting control and data.
 
@@ -815,7 +826,7 @@ config FB_XVR500
 	help
 	  This is the framebuffer device for the Sun XVR-500 and similar
 	  graphics cards based upon the 3DLABS Wildcat chipset.  The driver
-	  only works on sparc64 systems where the system firwmare has
+	  only works on sparc64 systems where the system firmware has
 	  mostly initialized the card already.  It is treated as a
 	  completely dumb framebuffer device.
 
@@ -828,7 +839,7 @@ config FB_XVR2500
 	help
 	  This is the framebuffer device for the Sun XVR-2500 and similar
 	  graphics cards based upon the 3DLABS Wildcat chipset.  The driver
-	  only works on sparc64 systems where the system firwmare has
+	  only works on sparc64 systems where the system firmware has
 	  mostly initialized the card already.  It is treated as a
 	  completely dumb framebuffer device.
 
@@ -878,7 +889,7 @@ config FB_S1D13XXX
 
 config FB_ATMEL
 	tristate "AT91/AT32 LCD Controller support"
-	depends on FB && (ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || AVR32)
+	depends on FB && (ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || AVR32)
 	select FB_CFB_FILLRECT
 	select FB_CFB_COPYAREA
 	select FB_CFB_IMAGEBLIT
@@ -1509,7 +1520,7 @@ config FB_VOODOO1
 
 	  WARNING: Do not use any application that uses the 3D engine
 	  (namely glide) while using this driver.
-	  Please read the <file:Documentation/fb/README-sstfb.txt> for supported
+	  Please read the <file:Documentation/fb/sstfb.txt> for supported
 	  options and other important info  support.
 
 config FB_VT8623
@@ -1807,7 +1818,7 @@ config FB_SM501
 	  This driver is also available as a module ( = code which can be
 	  inserted and removed from the running kernel whenever you want). The
 	  module will be called sm501fb. If you want to compile it as a module,
-	  say M here and read <file:Documentation/modules.txt>.
+	  say M here and read <file:Documentation/kbuild/modules.txt>.
 
 	  If unsure, say N.
 
@@ -1892,9 +1903,7 @@ config FB_VIRTUAL
 
 	  If unsure, say N.
 
-if ARCH_OMAP
-	source "drivers/video/omap/Kconfig"
-endif
+source "drivers/video/omap/Kconfig"
 
 source "drivers/video/backlight/Kconfig"
 source "drivers/video/display/Kconfig"