X-Git-Url: http://git.rot13.org/?a=blobdiff_plain;f=firmware%2Fapps%2Fchipcon%2Fchipcon.c;h=ce0a9ff03c06387b54cb4d82d29d07f2a7d4ed33;hb=3a05c18969fbbb1337db4f8559483c009c78ea12;hp=c2c2a27b1a3544b1aea21dde656f3b387cf37297;hpb=a456d2fbf645904f642f714fa86766f195384d94;p=goodfet

diff --git a/firmware/apps/chipcon/chipcon.c b/firmware/apps/chipcon/chipcon.c
index c2c2a27..ce0a9ff 100644
--- a/firmware/apps/chipcon/chipcon.c
+++ b/firmware/apps/chipcon/chipcon.c
@@ -37,7 +37,8 @@
 //This could be more accurate.
 //Does it ever need to be?
 #define CCSPEED 3
-#define CCDELAY(x) delay(x)
+//#define CCDELAY(x) delay(x)
+#define CCDELAY(x) 
 
 #define SETMOSI P5OUT|=MOSI
 #define CLRMOSI P5OUT&=~MOSI
@@ -52,34 +53,51 @@
 void ccsetup(){
   P5OUT|=MOSI+SCK+RST;
   P5DIR|=MOSI+SCK+RST;
-  //P5DIR&=~MISO;  //MOSI is MISO
-  
   //P5REN=0xFF;
-  
 }
 
+
+/* 33 cycle critical region
+0000000e <ccdebuginit>:
+   e:	f2 d0 0d 00 	bis.b	#13,	&0x0031	;5 cycles
+  12:	31 00 
+  14:	f2 c2 31 00 	bic.b	#8,	&0x0031	;4 cycles
+  18:	d2 c3 31 00 	bic.b	#1,	&0x0031	;4
+  1c:	f2 e2 31 00 	xor.b	#8,	&0x0031	;4
+  20:	f2 e2 31 00 	xor.b	#8,	&0x0031	;4
+  24:	f2 e2 31 00 	xor.b	#8,	&0x0031	;4
+  28:	f2 e2 31 00 	xor.b	#8,	&0x0031	;4
+  2c:	d2 d3 31 00 	bis.b	#1,	&0x0031	;4
+  30:	30 41       	ret			
+*/
+
+/*
 //! Initialize the debugger
 void ccdebuginit(){
-  delay(30); //So the beginning is ready for glitching.
+  //Port output BUT NOT DIRECTION is set at start.
+  P5OUT|=MOSI+SCK+RST;
+  
+  //delay(30); //So the beginning is ready for glitching.
   
   //Two positive debug clock pulses while !RST is low.
   //Take RST low, pulse twice, then high.
   P5OUT&=~SCK;
   P5OUT&=~RST;
   
-  //pulse twice
-  CCDELAY(CCSPEED);
-  P5OUT|=SCK;  //up
-  CCDELAY(CCSPEED);
-  P5OUT&=~SCK; //down
-  CCDELAY(CCSPEED);
-  P5OUT|=SCK;  //up
-  CCDELAY(CCSPEED);
-  P5OUT&=~SCK; //down
+  //Two rising edges.
+  P5OUT^=SCK; //up
+  P5OUT^=SCK; //down
+  P5OUT^=SCK; //up
+  P5OUT^=SCK; //Unnecessary.
+  
   
   //Raise !RST.
   P5OUT|=RST;
 }
+*/
+
+//! Initialize the debugger.
+void ccdebuginit(); 
 
 //! Read and write a CC bit.
 unsigned char cctrans8(unsigned char byte){
@@ -150,14 +168,12 @@ void cchandle(unsigned char app,
     if(cmddata[0]&0x4)
       ccread(1);
     txdata(app,verb,1);
-    
     break;
   case WRITE: //Write a command with no reply.
     cccmd(len);
     txdata(app,verb,0);
     break;
   case START://enter debugger
-    ccsetup();
     ccdebuginit();
     txdata(app,verb,0);
     break;
@@ -470,12 +486,12 @@ void cc_write_flash_page(u32 adr){
   cmddata[1]=0xc7;
   cmddata[2]=0x51;
   cc_debug_instr(3);
-  debugstr("Loaded bank info.");
+  //debugstr("Loaded bank info.");
   
   cc_set_pc(0xf000+MAXFLASHPAGE_SIZE);//execute code fragment
   cc_resume();
   
-  debugstr("Executing.");
+  //debugstr("Executing.");
   
   
   while(!(cc_read_status()&CC_STATUS_CPUHALTED)){
@@ -483,7 +499,7 @@ void cc_write_flash_page(u32 adr){
   }
   
   
-  debugstr("Done flashing.");
+  //debugstr("Done flashing.");
   
   P1OUT&=~1;//clear LED
 }