X-Git-Url: http://git.rot13.org/?a=blobdiff_plain;f=firmware%2Flib%2Fmsp430x1612.c;h=386119f48c8e4dd462b9341dfcb301345ef80a3d;hb=f0eaf8347f79d77ca7d1bcaf8018d3e3b1505649;hp=3bcb3ce0eab64617aabe14d8c4413c6b10403403;hpb=d817685970c7d0601be3434bed24f835dccbe234;p=goodfet

diff --git a/firmware/lib/msp430x1612.c b/firmware/lib/msp430x1612.c
index 3bcb3ce..386119f 100644
--- a/firmware/lib/msp430x1612.c
+++ b/firmware/lib/msp430x1612.c
@@ -6,7 +6,6 @@
 #include <io.h>
 #include <iomacros.h>
 
-
 //! Receive a byte.
 unsigned char serial_rx(){
   char c;
@@ -31,7 +30,6 @@ unsigned char serial1_rx(){
   return c;
 }
 
-
 //! Transmit a byte.
 void serial_tx(unsigned char x){
   while ((IFG1 & UTXIFG0) == 0); //loop until buffer is free
@@ -44,6 +42,14 @@ void serial1_tx(unsigned char x){
   TXBUF1 = x;
 }
 
+/** Later, add support for the EZ430/FETUIF with 12MHz crystal
+    UBR00=0xE2; UBR10=0x04; UMCTL0=0x00; // uart0 12000000Hz 9600bps
+    UBR00=0x71; UBR10=0x02; UMCTL0=0x00; // uart0 12000000Hz 19200bps
+    UBR00=0x38; UBR10=0x01; UMCTL0=0x55; // uart0 12000000Hz 38400bps
+    UBR00=0xD0; UBR10=0x00; UMCTL0=0x4A; // uart0 12000000Hz 57581bps
+    UBR00=0x68; UBR10=0x00; UMCTL0=0x04; // uart0 12000000Hz 115273bps
+ */
+
 //! Set the baud rate.
 void setbaud(unsigned char rate){
   
@@ -94,9 +100,122 @@ void setbaud1(unsigned char rate){
 
 
 void msp430_init_uart(){
+  
+  /* RS232 */
+  
+  P3SEL |= BIT4|BIT5;                        // P3.4,5 = USART0 TXD/RXD
+  P3DIR |= BIT4;
+  
+  UCTL0 = SWRST | CHAR;                 /* 8-bit character, UART mode */
+  UTCTL0 = SSEL1;                       /* UCLK = MCLK */
+  
+  setbaud(0);
+  
+  ME1 &= ~USPIE0;			/* USART1 SPI module disable */
+  ME1 |= (UTXE0 | URXE0);               /* Enable USART1 TXD/RXD */
+
+  UCTL0 &= ~SWRST;
+
+  /* XXX Clear pending interrupts before enable!!! */
+  U0TCTL |= URXSE;
+  
+  
+  //IE1 |= URXIE1;                        /* Enable USART1 RX interrupt  */
 }
 
 
+/** For EZ430/FETUIF
+ void msp430_init_dco() {
+  WDTCTL = WDTPW + WDTHOLD; //stop WDT
+
+  BCSCTL1 = 0;
+
+  do {
+    int i;
+    IFG1 &= ~OFIFG;
+    for (i=0; i<1000; i++);
+
+  } while (IFG1 & OFIFG);
+
+  BCSCTL2 = SELM1 | DIVM1 | SELS;
+
+}
+ */
+
 void msp430_init_dco() {
+/* This code taken from the FU Berlin sources and reformatted. */
+  //
+
+//Works well.
+//#define MSP430_CPU_SPEED 2457600UL
+
+//Too fast for internal resistor.
+//#define MSP430_CPU_SPEED 4915200UL
+
+//Max speed.
+//#deefine MSP430_CPU_SPEED 4500000UL
+
+//baud rate speed
+#define MSP430_CPU_SPEED 3683400UL
+#define DELTA    ((MSP430_CPU_SPEED) / (32768 / 8))
+  unsigned int compare, oldcapture = 0;
+  unsigned int i;
+  
+  WDTCTL = WDTPW + WDTHOLD; //stop WDT
+  
+  
+  DCOCTL=0xF0;
+  //a4
+  //1100
+
+  /* ACLK is devided by 4. RSEL=6 no division for MCLK
+     and SSMCLK. XT2 is off. */
+  //BCSCTL1 = 0xa8;
+  
+  BCSCTL2 = 0x00; /* Init FLL to desired frequency using the 32762Hz
+		     crystal DCO frquenzy = 2,4576 MHz  */
+  
+  P1OUT|=1;
+  
+  BCSCTL1 |= DIVA1 + DIVA0;             /* ACLK = LFXT1CLK/8 */
+  for(i = 0xffff; i > 0; i--) {         /* Delay for XTAL to settle */
+    asm("nop");
+  }
+
+  CCTL2 = CCIS0 + CM0 + CAP;            // Define CCR2, CAP, ACLK
+  TACTL = TASSEL1 + TACLR + MC1;        // SMCLK, continous mode
+
+
+  while(1) {
+
+    while((CCTL2 & CCIFG) != CCIFG);    /* Wait until capture occured! */
+    CCTL2 &= ~CCIFG;                    /* Capture occured, clear flag */
+    compare = CCR2;                     /* Get current captured SMCLK */
+    compare = compare - oldcapture;     /* SMCLK difference */
+    oldcapture = CCR2;                  /* Save current captured SMCLK */
+
+    if(DELTA == compare) {
+      break;                            /* if equal, leave "while(1)" */
+    } else if(DELTA < compare) {        /* DCO is too fast, slow it down */
+      DCOCTL--;
+      if(DCOCTL == 0xFF) {              /* Did DCO role under? */
+	BCSCTL1--;
+      }
+    } else {                            /* -> Select next lower RSEL */
+      DCOCTL++;
+      if(DCOCTL == 0x00) {              /* Did DCO role over? */
+	BCSCTL1++;
+      }
+                                        /* -> Select next higher RSEL  */
+    }
+  }
+  
+  CCTL2 = 0;                            /* Stop CCR2 function */
+  TACTL = 0;                            /* Stop Timer_A */
+
+  BCSCTL1 &= ~(DIVA1 + DIVA0);          /* remove /8 divisor from ACLK again */
+  
+  P1OUT=0;
+
 }