ipath_eeprom.o \
ipath_file_ops.o \
ipath_fs.o \
- ipath_ht400.o \
+ ipath_iba6110.o \
+ ipath_iba6120.o \
ipath_init_chip.o \
ipath_intr.o \
ipath_keys.o \
ipath_mad.o \
ipath_mmap.o \
ipath_mr.o \
- ipath_pe800.o \
ipath_qp.o \
ipath_rc.o \
ipath_ruc.o \
/* setup the chip-specific functions, as early as possible. */
switch (ent->device) {
case PCI_DEVICE_ID_INFINIPATH_HT:
- ipath_init_ht400_funcs(dd);
+ ipath_init_iba6110_funcs(dd);
break;
case PCI_DEVICE_ID_INFINIPATH_PE800:
- ipath_init_pe800_funcs(dd);
+ ipath_init_iba6120_funcs(dd);
break;
default:
ipath_dev_err(dd, "Found unknown QLogic deviceid 0x%x, "
*/
if (l == hdrqtail || (i && !(i&0xf))) {
u64 lval;
- if (l == hdrqtail) /* PE-800 interrupt only on last */
+ if (l == hdrqtail)
+ /* request IBA6120 interrupt only on last */
lval = dd->ipath_rhdrhead_intr_off | l;
else
lval = l;
}
if (!dd->ipath_rhdrhead_intr_off && !reloop) {
- /* HT-400 workaround; we can have a race clearing chip
+ /* IBA6110 workaround; we can have a race clearing chip
* interrupt with another interrupt about to be delivered,
* and can clear it before it is delivered on the GPIO
* workaround. By doing the extra check here for the
ret = mmap_rcvegrbufs(vma, pd);
else if (pgaddr == (u64) pd->port_rcvhdrq_phys) {
/*
- * The rcvhdrq itself; readonly except on HT-400 (so have
+ * The rcvhdrq itself; readonly except on HT (so have
* to allow writable mapping), multiple pages, contiguous
* from an i/o perspective.
*/
* This code is present to allow a knowledgeable person to
* specify the layout of processes to processors before opening
* this driver, and then we'll assign the process to the "closest"
- * HT-400 to that processor (we assume reasonable connectivity,
+ * InfiniPath chip to that processor (we assume reasonable connectivity,
* for now). This code assumes that if affinity has been set
* before this point, that at most one cpu is set; for now this
* is reasonable. I check for both cpus_empty() and cpus_full(),
* in case some kernel variant sets none of the bits when no
* affinity is set. 2.6.11 and 12 kernels have all present
* cpus set. Some day we'll have to fix it up further to handle
- * a cpu subset. This algorithm fails for two HT-400's connected
+ * a cpu subset. This algorithm fails for two HT chips connected
* in tunnel fashion. Eventually this needs real topology
* information. There may be some issues with dual core numbering
* as well. This needs more work prior to release.
+++ /dev/null
-/*
- * Copyright (c) 2006 QLogic, Inc. All rights reserved.
- * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
- *
- * This software is available to you under a choice of one of two
- * licenses. You may choose to be licensed under the terms of the GNU
- * General Public License (GPL) Version 2, available from the file
- * COPYING in the main directory of this source tree, or the
- * OpenIB.org BSD license below:
- *
- * Redistribution and use in source and binary forms, with or
- * without modification, are permitted provided that the following
- * conditions are met:
- *
- * - Redistributions of source code must retain the above
- * copyright notice, this list of conditions and the following
- * disclaimer.
- *
- * - Redistributions in binary form must reproduce the above
- * copyright notice, this list of conditions and the following
- * disclaimer in the documentation and/or other materials
- * provided with the distribution.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
- * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
- * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
- * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
- * SOFTWARE.
- */
-
-/*
- * This file contains all of the code that is specific to the InfiniPath
- * HT-400 chip.
- */
-
-#include <linux/pci.h>
-#include <linux/delay.h>
-
-#include "ipath_kernel.h"
-#include "ipath_registers.h"
-
-/*
- * This lists the InfiniPath HT400 registers, in the actual chip layout.
- * This structure should never be directly accessed.
- *
- * The names are in InterCap form because they're taken straight from
- * the chip specification. Since they're only used in this file, they
- * don't pollute the rest of the source.
-*/
-
-struct _infinipath_do_not_use_kernel_regs {
- unsigned long long Revision;
- unsigned long long Control;
- unsigned long long PageAlign;
- unsigned long long PortCnt;
- unsigned long long DebugPortSelect;
- unsigned long long DebugPort;
- unsigned long long SendRegBase;
- unsigned long long UserRegBase;
- unsigned long long CounterRegBase;
- unsigned long long Scratch;
- unsigned long long ReservedMisc1;
- unsigned long long InterruptConfig;
- unsigned long long IntBlocked;
- unsigned long long IntMask;
- unsigned long long IntStatus;
- unsigned long long IntClear;
- unsigned long long ErrorMask;
- unsigned long long ErrorStatus;
- unsigned long long ErrorClear;
- unsigned long long HwErrMask;
- unsigned long long HwErrStatus;
- unsigned long long HwErrClear;
- unsigned long long HwDiagCtrl;
- unsigned long long MDIO;
- unsigned long long IBCStatus;
- unsigned long long IBCCtrl;
- unsigned long long ExtStatus;
- unsigned long long ExtCtrl;
- unsigned long long GPIOOut;
- unsigned long long GPIOMask;
- unsigned long long GPIOStatus;
- unsigned long long GPIOClear;
- unsigned long long RcvCtrl;
- unsigned long long RcvBTHQP;
- unsigned long long RcvHdrSize;
- unsigned long long RcvHdrCnt;
- unsigned long long RcvHdrEntSize;
- unsigned long long RcvTIDBase;
- unsigned long long RcvTIDCnt;
- unsigned long long RcvEgrBase;
- unsigned long long RcvEgrCnt;
- unsigned long long RcvBufBase;
- unsigned long long RcvBufSize;
- unsigned long long RxIntMemBase;
- unsigned long long RxIntMemSize;
- unsigned long long RcvPartitionKey;
- unsigned long long ReservedRcv[10];
- unsigned long long SendCtrl;
- unsigned long long SendPIOBufBase;
- unsigned long long SendPIOSize;
- unsigned long long SendPIOBufCnt;
- unsigned long long SendPIOAvailAddr;
- unsigned long long TxIntMemBase;
- unsigned long long TxIntMemSize;
- unsigned long long ReservedSend[9];
- unsigned long long SendBufferError;
- unsigned long long SendBufferErrorCONT1;
- unsigned long long SendBufferErrorCONT2;
- unsigned long long SendBufferErrorCONT3;
- unsigned long long ReservedSBE[4];
- unsigned long long RcvHdrAddr0;
- unsigned long long RcvHdrAddr1;
- unsigned long long RcvHdrAddr2;
- unsigned long long RcvHdrAddr3;
- unsigned long long RcvHdrAddr4;
- unsigned long long RcvHdrAddr5;
- unsigned long long RcvHdrAddr6;
- unsigned long long RcvHdrAddr7;
- unsigned long long RcvHdrAddr8;
- unsigned long long ReservedRHA[7];
- unsigned long long RcvHdrTailAddr0;
- unsigned long long RcvHdrTailAddr1;
- unsigned long long RcvHdrTailAddr2;
- unsigned long long RcvHdrTailAddr3;
- unsigned long long RcvHdrTailAddr4;
- unsigned long long RcvHdrTailAddr5;
- unsigned long long RcvHdrTailAddr6;
- unsigned long long RcvHdrTailAddr7;
- unsigned long long RcvHdrTailAddr8;
- unsigned long long ReservedRHTA[7];
- unsigned long long Sync; /* Software only */
- unsigned long long Dump; /* Software only */
- unsigned long long SimVer; /* Software only */
- unsigned long long ReservedSW[5];
- unsigned long long SerdesConfig0;
- unsigned long long SerdesConfig1;
- unsigned long long SerdesStatus;
- unsigned long long XGXSConfig;
- unsigned long long ReservedSW2[4];
-};
-
-#define IPATH_KREG_OFFSET(field) (offsetof(struct \
- _infinipath_do_not_use_kernel_regs, field) / sizeof(u64))
-#define IPATH_CREG_OFFSET(field) (offsetof( \
- struct infinipath_counters, field) / sizeof(u64))
-
-static const struct ipath_kregs ipath_ht_kregs = {
- .kr_control = IPATH_KREG_OFFSET(Control),
- .kr_counterregbase = IPATH_KREG_OFFSET(CounterRegBase),
- .kr_debugport = IPATH_KREG_OFFSET(DebugPort),
- .kr_debugportselect = IPATH_KREG_OFFSET(DebugPortSelect),
- .kr_errorclear = IPATH_KREG_OFFSET(ErrorClear),
- .kr_errormask = IPATH_KREG_OFFSET(ErrorMask),
- .kr_errorstatus = IPATH_KREG_OFFSET(ErrorStatus),
- .kr_extctrl = IPATH_KREG_OFFSET(ExtCtrl),
- .kr_extstatus = IPATH_KREG_OFFSET(ExtStatus),
- .kr_gpio_clear = IPATH_KREG_OFFSET(GPIOClear),
- .kr_gpio_mask = IPATH_KREG_OFFSET(GPIOMask),
- .kr_gpio_out = IPATH_KREG_OFFSET(GPIOOut),
- .kr_gpio_status = IPATH_KREG_OFFSET(GPIOStatus),
- .kr_hwdiagctrl = IPATH_KREG_OFFSET(HwDiagCtrl),
- .kr_hwerrclear = IPATH_KREG_OFFSET(HwErrClear),
- .kr_hwerrmask = IPATH_KREG_OFFSET(HwErrMask),
- .kr_hwerrstatus = IPATH_KREG_OFFSET(HwErrStatus),
- .kr_ibcctrl = IPATH_KREG_OFFSET(IBCCtrl),
- .kr_ibcstatus = IPATH_KREG_OFFSET(IBCStatus),
- .kr_intblocked = IPATH_KREG_OFFSET(IntBlocked),
- .kr_intclear = IPATH_KREG_OFFSET(IntClear),
- .kr_interruptconfig = IPATH_KREG_OFFSET(InterruptConfig),
- .kr_intmask = IPATH_KREG_OFFSET(IntMask),
- .kr_intstatus = IPATH_KREG_OFFSET(IntStatus),
- .kr_mdio = IPATH_KREG_OFFSET(MDIO),
- .kr_pagealign = IPATH_KREG_OFFSET(PageAlign),
- .kr_partitionkey = IPATH_KREG_OFFSET(RcvPartitionKey),
- .kr_portcnt = IPATH_KREG_OFFSET(PortCnt),
- .kr_rcvbthqp = IPATH_KREG_OFFSET(RcvBTHQP),
- .kr_rcvbufbase = IPATH_KREG_OFFSET(RcvBufBase),
- .kr_rcvbufsize = IPATH_KREG_OFFSET(RcvBufSize),
- .kr_rcvctrl = IPATH_KREG_OFFSET(RcvCtrl),
- .kr_rcvegrbase = IPATH_KREG_OFFSET(RcvEgrBase),
- .kr_rcvegrcnt = IPATH_KREG_OFFSET(RcvEgrCnt),
- .kr_rcvhdrcnt = IPATH_KREG_OFFSET(RcvHdrCnt),
- .kr_rcvhdrentsize = IPATH_KREG_OFFSET(RcvHdrEntSize),
- .kr_rcvhdrsize = IPATH_KREG_OFFSET(RcvHdrSize),
- .kr_rcvintmembase = IPATH_KREG_OFFSET(RxIntMemBase),
- .kr_rcvintmemsize = IPATH_KREG_OFFSET(RxIntMemSize),
- .kr_rcvtidbase = IPATH_KREG_OFFSET(RcvTIDBase),
- .kr_rcvtidcnt = IPATH_KREG_OFFSET(RcvTIDCnt),
- .kr_revision = IPATH_KREG_OFFSET(Revision),
- .kr_scratch = IPATH_KREG_OFFSET(Scratch),
- .kr_sendbuffererror = IPATH_KREG_OFFSET(SendBufferError),
- .kr_sendctrl = IPATH_KREG_OFFSET(SendCtrl),
- .kr_sendpioavailaddr = IPATH_KREG_OFFSET(SendPIOAvailAddr),
- .kr_sendpiobufbase = IPATH_KREG_OFFSET(SendPIOBufBase),
- .kr_sendpiobufcnt = IPATH_KREG_OFFSET(SendPIOBufCnt),
- .kr_sendpiosize = IPATH_KREG_OFFSET(SendPIOSize),
- .kr_sendregbase = IPATH_KREG_OFFSET(SendRegBase),
- .kr_txintmembase = IPATH_KREG_OFFSET(TxIntMemBase),
- .kr_txintmemsize = IPATH_KREG_OFFSET(TxIntMemSize),
- .kr_userregbase = IPATH_KREG_OFFSET(UserRegBase),
- .kr_serdesconfig0 = IPATH_KREG_OFFSET(SerdesConfig0),
- .kr_serdesconfig1 = IPATH_KREG_OFFSET(SerdesConfig1),
- .kr_serdesstatus = IPATH_KREG_OFFSET(SerdesStatus),
- .kr_xgxsconfig = IPATH_KREG_OFFSET(XGXSConfig),
- /*
- * These should not be used directly via ipath_read_kreg64(),
- * use them with ipath_read_kreg64_port(),
- */
- .kr_rcvhdraddr = IPATH_KREG_OFFSET(RcvHdrAddr0),
- .kr_rcvhdrtailaddr = IPATH_KREG_OFFSET(RcvHdrTailAddr0)
-};
-
-static const struct ipath_cregs ipath_ht_cregs = {
- .cr_badformatcnt = IPATH_CREG_OFFSET(RxBadFormatCnt),
- .cr_erricrccnt = IPATH_CREG_OFFSET(RxICRCErrCnt),
- .cr_errlinkcnt = IPATH_CREG_OFFSET(RxLinkProblemCnt),
- .cr_errlpcrccnt = IPATH_CREG_OFFSET(RxLPCRCErrCnt),
- .cr_errpkey = IPATH_CREG_OFFSET(RxPKeyMismatchCnt),
- .cr_errrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowCtrlErrCnt),
- .cr_err_rlencnt = IPATH_CREG_OFFSET(RxLenErrCnt),
- .cr_errslencnt = IPATH_CREG_OFFSET(TxLenErrCnt),
- .cr_errtidfull = IPATH_CREG_OFFSET(RxTIDFullErrCnt),
- .cr_errtidvalid = IPATH_CREG_OFFSET(RxTIDValidErrCnt),
- .cr_errvcrccnt = IPATH_CREG_OFFSET(RxVCRCErrCnt),
- .cr_ibstatuschange = IPATH_CREG_OFFSET(IBStatusChangeCnt),
- /* calc from Reg_CounterRegBase + offset */
- .cr_intcnt = IPATH_CREG_OFFSET(LBIntCnt),
- .cr_invalidrlencnt = IPATH_CREG_OFFSET(RxMaxMinLenErrCnt),
- .cr_invalidslencnt = IPATH_CREG_OFFSET(TxMaxMinLenErrCnt),
- .cr_lbflowstallcnt = IPATH_CREG_OFFSET(LBFlowStallCnt),
- .cr_pktrcvcnt = IPATH_CREG_OFFSET(RxDataPktCnt),
- .cr_pktrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowPktCnt),
- .cr_pktsendcnt = IPATH_CREG_OFFSET(TxDataPktCnt),
- .cr_pktsendflowcnt = IPATH_CREG_OFFSET(TxFlowPktCnt),
- .cr_portovflcnt = IPATH_CREG_OFFSET(RxP0HdrEgrOvflCnt),
- .cr_rcvebpcnt = IPATH_CREG_OFFSET(RxEBPCnt),
- .cr_rcvovflcnt = IPATH_CREG_OFFSET(RxBufOvflCnt),
- .cr_senddropped = IPATH_CREG_OFFSET(TxDroppedPktCnt),
- .cr_sendstallcnt = IPATH_CREG_OFFSET(TxFlowStallCnt),
- .cr_sendunderruncnt = IPATH_CREG_OFFSET(TxUnderrunCnt),
- .cr_wordrcvcnt = IPATH_CREG_OFFSET(RxDwordCnt),
- .cr_wordsendcnt = IPATH_CREG_OFFSET(TxDwordCnt),
- .cr_unsupvlcnt = IPATH_CREG_OFFSET(TxUnsupVLErrCnt),
- .cr_rxdroppktcnt = IPATH_CREG_OFFSET(RxDroppedPktCnt),
- .cr_iblinkerrrecovcnt = IPATH_CREG_OFFSET(IBLinkErrRecoveryCnt),
- .cr_iblinkdowncnt = IPATH_CREG_OFFSET(IBLinkDownedCnt),
- .cr_ibsymbolerrcnt = IPATH_CREG_OFFSET(IBSymbolErrCnt)
-};
-
-/* kr_intstatus, kr_intclear, kr_intmask bits */
-#define INFINIPATH_I_RCVURG_MASK 0x1FF
-#define INFINIPATH_I_RCVAVAIL_MASK 0x1FF
-
-/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */
-#define INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT 0
-#define INFINIPATH_HWE_HTCMEMPARITYERR_MASK 0x3FFFFFULL
-#define INFINIPATH_HWE_HTCLNKABYTE0CRCERR 0x0000000000800000ULL
-#define INFINIPATH_HWE_HTCLNKABYTE1CRCERR 0x0000000001000000ULL
-#define INFINIPATH_HWE_HTCLNKBBYTE0CRCERR 0x0000000002000000ULL
-#define INFINIPATH_HWE_HTCLNKBBYTE1CRCERR 0x0000000004000000ULL
-#define INFINIPATH_HWE_HTCMISCERR4 0x0000000008000000ULL
-#define INFINIPATH_HWE_HTCMISCERR5 0x0000000010000000ULL
-#define INFINIPATH_HWE_HTCMISCERR6 0x0000000020000000ULL
-#define INFINIPATH_HWE_HTCMISCERR7 0x0000000040000000ULL
-#define INFINIPATH_HWE_HTCBUSTREQPARITYERR 0x0000000080000000ULL
-#define INFINIPATH_HWE_HTCBUSTRESPPARITYERR 0x0000000100000000ULL
-#define INFINIPATH_HWE_HTCBUSIREQPARITYERR 0x0000000200000000ULL
-#define INFINIPATH_HWE_COREPLL_FBSLIP 0x0080000000000000ULL
-#define INFINIPATH_HWE_COREPLL_RFSLIP 0x0100000000000000ULL
-#define INFINIPATH_HWE_HTBPLL_FBSLIP 0x0200000000000000ULL
-#define INFINIPATH_HWE_HTBPLL_RFSLIP 0x0400000000000000ULL
-#define INFINIPATH_HWE_HTAPLL_FBSLIP 0x0800000000000000ULL
-#define INFINIPATH_HWE_HTAPLL_RFSLIP 0x1000000000000000ULL
-#define INFINIPATH_HWE_SERDESPLLFAILED 0x2000000000000000ULL
-
-/* kr_extstatus bits */
-#define INFINIPATH_EXTS_FREQSEL 0x2
-#define INFINIPATH_EXTS_SERDESSEL 0x4
-#define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000
-#define INFINIPATH_EXTS_MEMBIST_CORRECT 0x0000000000008000
-
-/*
- * masks and bits that are different in different chips, or present only
- * in one
- */
-static const ipath_err_t infinipath_hwe_htcmemparityerr_mask =
- INFINIPATH_HWE_HTCMEMPARITYERR_MASK;
-static const ipath_err_t infinipath_hwe_htcmemparityerr_shift =
- INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT;
-
-static const ipath_err_t infinipath_hwe_htclnkabyte0crcerr =
- INFINIPATH_HWE_HTCLNKABYTE0CRCERR;
-static const ipath_err_t infinipath_hwe_htclnkabyte1crcerr =
- INFINIPATH_HWE_HTCLNKABYTE1CRCERR;
-static const ipath_err_t infinipath_hwe_htclnkbbyte0crcerr =
- INFINIPATH_HWE_HTCLNKBBYTE0CRCERR;
-static const ipath_err_t infinipath_hwe_htclnkbbyte1crcerr =
- INFINIPATH_HWE_HTCLNKBBYTE1CRCERR;
-
-#define _IPATH_GPIO_SDA_NUM 1
-#define _IPATH_GPIO_SCL_NUM 0
-
-#define IPATH_GPIO_SDA \
- (1ULL << (_IPATH_GPIO_SDA_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
-#define IPATH_GPIO_SCL \
- (1ULL << (_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
-
-/* keep the code below somewhat more readonable; not used elsewhere */
-#define _IPATH_HTLINK0_CRCBITS (infinipath_hwe_htclnkabyte0crcerr | \
- infinipath_hwe_htclnkabyte1crcerr)
-#define _IPATH_HTLINK1_CRCBITS (infinipath_hwe_htclnkbbyte0crcerr | \
- infinipath_hwe_htclnkbbyte1crcerr)
-#define _IPATH_HTLANE0_CRCBITS (infinipath_hwe_htclnkabyte0crcerr | \
- infinipath_hwe_htclnkbbyte0crcerr)
-#define _IPATH_HTLANE1_CRCBITS (infinipath_hwe_htclnkabyte1crcerr | \
- infinipath_hwe_htclnkbbyte1crcerr)
-
-static void hwerr_crcbits(struct ipath_devdata *dd, ipath_err_t hwerrs,
- char *msg, size_t msgl)
-{
- char bitsmsg[64];
- ipath_err_t crcbits = hwerrs &
- (_IPATH_HTLINK0_CRCBITS | _IPATH_HTLINK1_CRCBITS);
- /* don't check if 8bit HT */
- if (dd->ipath_flags & IPATH_8BIT_IN_HT0)
- crcbits &= ~infinipath_hwe_htclnkabyte1crcerr;
- /* don't check if 8bit HT */
- if (dd->ipath_flags & IPATH_8BIT_IN_HT1)
- crcbits &= ~infinipath_hwe_htclnkbbyte1crcerr;
- /*
- * we'll want to ignore link errors on link that is
- * not in use, if any. For now, complain about both
- */
- if (crcbits) {
- u16 ctrl0, ctrl1;
- snprintf(bitsmsg, sizeof bitsmsg,
- "[HT%s lane %s CRC (%llx); ignore till reload]",
- !(crcbits & _IPATH_HTLINK1_CRCBITS) ?
- "0 (A)" : (!(crcbits & _IPATH_HTLINK0_CRCBITS)
- ? "1 (B)" : "0+1 (A+B)"),
- !(crcbits & _IPATH_HTLANE1_CRCBITS) ? "0"
- : (!(crcbits & _IPATH_HTLANE0_CRCBITS) ? "1" :
- "0+1"), (unsigned long long) crcbits);
- strlcat(msg, bitsmsg, msgl);
-
- /*
- * print extra info for debugging. slave/primary
- * config word 4, 8 (link control 0, 1)
- */
-
- if (pci_read_config_word(dd->pcidev,
- dd->ipath_ht_slave_off + 0x4,
- &ctrl0))
- dev_info(&dd->pcidev->dev, "Couldn't read "
- "linkctrl0 of slave/primary "
- "config block\n");
- else if (!(ctrl0 & 1 << 6))
- /* not if EOC bit set */
- ipath_dbg("HT linkctrl0 0x%x%s%s\n", ctrl0,
- ((ctrl0 >> 8) & 7) ? " CRC" : "",
- ((ctrl0 >> 4) & 1) ? "linkfail" :
- "");
- if (pci_read_config_word(dd->pcidev,
- dd->ipath_ht_slave_off + 0x8,
- &ctrl1))
- dev_info(&dd->pcidev->dev, "Couldn't read "
- "linkctrl1 of slave/primary "
- "config block\n");
- else if (!(ctrl1 & 1 << 6))
- /* not if EOC bit set */
- ipath_dbg("HT linkctrl1 0x%x%s%s\n", ctrl1,
- ((ctrl1 >> 8) & 7) ? " CRC" : "",
- ((ctrl1 >> 4) & 1) ? "linkfail" :
- "");
-
- /* disable until driver reloaded */
- dd->ipath_hwerrmask &= ~crcbits;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
- dd->ipath_hwerrmask);
- ipath_dbg("HT crc errs: %s\n", msg);
- } else
- ipath_dbg("ignoring HT crc errors 0x%llx, "
- "not in use\n", (unsigned long long)
- (hwerrs & (_IPATH_HTLINK0_CRCBITS |
- _IPATH_HTLINK1_CRCBITS)));
-}
-
-/**
- * ipath_ht_handle_hwerrors - display hardware errors
- * @dd: the infinipath device
- * @msg: the output buffer
- * @msgl: the size of the output buffer
- *
- * Use same msg buffer as regular errors to avoid
- * excessive stack use. Most hardware errors are catastrophic, but for
- * right now, we'll print them and continue.
- * We reuse the same message buffer as ipath_handle_errors() to avoid
- * excessive stack usage.
- */
-static void ipath_ht_handle_hwerrors(struct ipath_devdata *dd, char *msg,
- size_t msgl)
-{
- ipath_err_t hwerrs;
- u32 bits, ctrl;
- int isfatal = 0;
- char bitsmsg[64];
-
- hwerrs = ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus);
-
- if (!hwerrs) {
- ipath_cdbg(VERBOSE, "Called but no hardware errors set\n");
- /*
- * better than printing cofusing messages
- * This seems to be related to clearing the crc error, or
- * the pll error during init.
- */
- goto bail;
- } else if (hwerrs == -1LL) {
- ipath_dev_err(dd, "Read of hardware error status failed "
- "(all bits set); ignoring\n");
- goto bail;
- }
- ipath_stats.sps_hwerrs++;
-
- /* Always clear the error status register, except MEMBISTFAIL,
- * regardless of whether we continue or stop using the chip.
- * We want that set so we know it failed, even across driver reload.
- * We'll still ignore it in the hwerrmask. We do this partly for
- * diagnostics, but also for support */
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
- hwerrs&~INFINIPATH_HWE_MEMBISTFAILED);
-
- hwerrs &= dd->ipath_hwerrmask;
-
- /*
- * make sure we get this much out, unless told to be quiet,
- * or it's occurred within the last 5 seconds
- */
- if ((hwerrs & ~dd->ipath_lasthwerror) ||
- (ipath_debug & __IPATH_VERBDBG))
- dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx "
- "(cleared)\n", (unsigned long long) hwerrs);
- dd->ipath_lasthwerror |= hwerrs;
-
- if (hwerrs & ~infinipath_hwe_bitsextant)
- ipath_dev_err(dd, "hwerror interrupt with unknown errors "
- "%llx set\n", (unsigned long long)
- (hwerrs & ~infinipath_hwe_bitsextant));
-
- ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control);
- if (ctrl & INFINIPATH_C_FREEZEMODE) {
- if (hwerrs) {
- /*
- * if any set that we aren't ignoring; only
- * make the complaint once, in case it's stuck
- * or recurring, and we get here multiple
- * times.
- */
- if (dd->ipath_flags & IPATH_INITTED) {
- ipath_dev_err(dd, "Fatal Error (freeze "
- "mode), no longer usable\n");
- isfatal = 1;
- }
- *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY;
- /* mark as having had error */
- *dd->ipath_statusp |= IPATH_STATUS_HWERROR;
- /*
- * mark as not usable, at a minimum until driver
- * is reloaded, probably until reboot, since no
- * other reset is possible.
- */
- dd->ipath_flags &= ~IPATH_INITTED;
- } else {
- ipath_dbg("Clearing freezemode on ignored hardware "
- "error\n");
- ctrl &= ~INFINIPATH_C_FREEZEMODE;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
- ctrl);
- }
- }
-
- *msg = '\0';
-
- /*
- * may someday want to decode into which bits are which
- * functional area for parity errors, etc.
- */
- if (hwerrs & (infinipath_hwe_htcmemparityerr_mask
- << INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT)) {
- bits = (u32) ((hwerrs >>
- INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT) &
- INFINIPATH_HWE_HTCMEMPARITYERR_MASK);
- snprintf(bitsmsg, sizeof bitsmsg, "[HTC Parity Errs %x] ",
- bits);
- strlcat(msg, bitsmsg, msgl);
- }
- if (hwerrs & (INFINIPATH_HWE_RXEMEMPARITYERR_MASK
- << INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT)) {
- bits = (u32) ((hwerrs >>
- INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) &
- INFINIPATH_HWE_RXEMEMPARITYERR_MASK);
- snprintf(bitsmsg, sizeof bitsmsg, "[RXE Parity Errs %x] ",
- bits);
- strlcat(msg, bitsmsg, msgl);
- }
- if (hwerrs & (INFINIPATH_HWE_TXEMEMPARITYERR_MASK
- << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)) {
- bits = (u32) ((hwerrs >>
- INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) &
- INFINIPATH_HWE_TXEMEMPARITYERR_MASK);
- snprintf(bitsmsg, sizeof bitsmsg, "[TXE Parity Errs %x] ",
- bits);
- strlcat(msg, bitsmsg, msgl);
- }
- if (hwerrs & INFINIPATH_HWE_IBCBUSTOSPCPARITYERR)
- strlcat(msg, "[IB2IPATH Parity]", msgl);
- if (hwerrs & INFINIPATH_HWE_IBCBUSFRSPCPARITYERR)
- strlcat(msg, "[IPATH2IB Parity]", msgl);
- if (hwerrs & INFINIPATH_HWE_HTCBUSIREQPARITYERR)
- strlcat(msg, "[HTC Ireq Parity]", msgl);
- if (hwerrs & INFINIPATH_HWE_HTCBUSTREQPARITYERR)
- strlcat(msg, "[HTC Treq Parity]", msgl);
- if (hwerrs & INFINIPATH_HWE_HTCBUSTRESPPARITYERR)
- strlcat(msg, "[HTC Tresp Parity]", msgl);
-
- if (hwerrs & (_IPATH_HTLINK0_CRCBITS | _IPATH_HTLINK1_CRCBITS))
- hwerr_crcbits(dd, hwerrs, msg, msgl);
-
- if (hwerrs & INFINIPATH_HWE_HTCMISCERR5)
- strlcat(msg, "[HT core Misc5]", msgl);
- if (hwerrs & INFINIPATH_HWE_HTCMISCERR6)
- strlcat(msg, "[HT core Misc6]", msgl);
- if (hwerrs & INFINIPATH_HWE_HTCMISCERR7)
- strlcat(msg, "[HT core Misc7]", msgl);
- if (hwerrs & INFINIPATH_HWE_MEMBISTFAILED) {
- strlcat(msg, "[Memory BIST test failed, HT-400 unusable]",
- msgl);
- /* ignore from now on, so disable until driver reloaded */
- dd->ipath_hwerrmask &= ~INFINIPATH_HWE_MEMBISTFAILED;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
- dd->ipath_hwerrmask);
- }
-#define _IPATH_PLL_FAIL (INFINIPATH_HWE_COREPLL_FBSLIP | \
- INFINIPATH_HWE_COREPLL_RFSLIP | \
- INFINIPATH_HWE_HTBPLL_FBSLIP | \
- INFINIPATH_HWE_HTBPLL_RFSLIP | \
- INFINIPATH_HWE_HTAPLL_FBSLIP | \
- INFINIPATH_HWE_HTAPLL_RFSLIP)
-
- if (hwerrs & _IPATH_PLL_FAIL) {
- snprintf(bitsmsg, sizeof bitsmsg,
- "[PLL failed (%llx), HT-400 unusable]",
- (unsigned long long) (hwerrs & _IPATH_PLL_FAIL));
- strlcat(msg, bitsmsg, msgl);
- /* ignore from now on, so disable until driver reloaded */
- dd->ipath_hwerrmask &= ~(hwerrs & _IPATH_PLL_FAIL);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
- dd->ipath_hwerrmask);
- }
-
- if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED) {
- /*
- * If it occurs, it is left masked since the eternal
- * interface is unused
- */
- dd->ipath_hwerrmask &= ~INFINIPATH_HWE_SERDESPLLFAILED;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
- dd->ipath_hwerrmask);
- }
-
- if (hwerrs & INFINIPATH_HWE_RXDSYNCMEMPARITYERR)
- strlcat(msg, "[Rx Dsync]", msgl);
- if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED)
- strlcat(msg, "[SerDes PLL]", msgl);
-
- ipath_dev_err(dd, "%s hardware error\n", msg);
- if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg)
- /*
- * for status file; if no trailing brace is copied,
- * we'll know it was truncated.
- */
- snprintf(dd->ipath_freezemsg,
- dd->ipath_freezelen, "{%s}", msg);
-
-bail:;
-}
-
-/**
- * ipath_ht_boardname - fill in the board name
- * @dd: the infinipath device
- * @name: the output buffer
- * @namelen: the size of the output buffer
- *
- * fill in the board name, based on the board revision register
- */
-static int ipath_ht_boardname(struct ipath_devdata *dd, char *name,
- size_t namelen)
-{
- char *n = NULL;
- u8 boardrev = dd->ipath_boardrev;
- int ret;
-
- switch (boardrev) {
- case 4: /* Ponderosa is one of the bringup boards */
- n = "Ponderosa";
- break;
- case 5:
- /*
- * HT-460 original production board; two production levels, with
- * different serial number ranges. See ipath_ht_early_init() for
- * case where we enable IPATH_GPIO_INTR for later serial # range.
- */
- n = "InfiniPath_HT-460";
- break;
- case 6:
- n = "OEM_Board_3";
- break;
- case 7:
- /* HT-460 small form factor production board */
- n = "InfiniPath_HT-465";
- break;
- case 8:
- n = "LS/X-1";
- break;
- case 9: /* Comstock bringup test board */
- n = "Comstock";
- break;
- case 10:
- n = "OEM_Board_2";
- break;
- case 11:
- n = "InfiniPath_HT-470";
- break;
- case 12:
- n = "OEM_Board_4";
- break;
- default: /* don't know, just print the number */
- ipath_dev_err(dd, "Don't yet know about board "
- "with ID %u\n", boardrev);
- snprintf(name, namelen, "Unknown_InfiniPath_HT-4xx_%u",
- boardrev);
- break;
- }
- if (n)
- snprintf(name, namelen, "%s", n);
-
- if (dd->ipath_majrev != 3 || (dd->ipath_minrev < 2 || dd->ipath_minrev > 3)) {
- /*
- * This version of the driver only supports the HT-400
- * Rev 3.2
- */
- ipath_dev_err(dd,
- "Unsupported HT-400 revision %u.%u!\n",
- dd->ipath_majrev, dd->ipath_minrev);
- ret = 1;
- goto bail;
- }
- /*
- * pkt/word counters are 32 bit, and therefore wrap fast enough
- * that we snapshot them from a timer, and maintain 64 bit shadow
- * copies
- */
- dd->ipath_flags |= IPATH_32BITCOUNTERS;
- if (dd->ipath_htspeed != 800)
- ipath_dev_err(dd,
- "Incorrectly configured for HT @ %uMHz\n",
- dd->ipath_htspeed);
- if (dd->ipath_boardrev == 7 || dd->ipath_boardrev == 11 ||
- dd->ipath_boardrev == 6)
- dd->ipath_flags |= IPATH_GPIO_INTR;
- else
- dd->ipath_flags |= IPATH_POLL_RX_INTR;
- if (dd->ipath_boardrev == 8) { /* LS/X-1 */
- u64 val;
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
- if (val & INFINIPATH_EXTS_SERDESSEL) {
- /*
- * hardware disabled
- *
- * This means that the chip is hardware disabled,
- * and will not be able to bring up the link,
- * in any case. We special case this and abort
- * early, to avoid later messages. We also set
- * the DISABLED status bit
- */
- ipath_dbg("Unit %u is hardware-disabled\n",
- dd->ipath_unit);
- *dd->ipath_statusp |= IPATH_STATUS_DISABLED;
- /* this value is handled differently */
- ret = 2;
- goto bail;
- }
- }
- ret = 0;
-
-bail:
- return ret;
-}
-
-static void ipath_check_htlink(struct ipath_devdata *dd)
-{
- u8 linkerr, link_off, i;
-
- for (i = 0; i < 2; i++) {
- link_off = dd->ipath_ht_slave_off + i * 4 + 0xd;
- if (pci_read_config_byte(dd->pcidev, link_off, &linkerr))
- dev_info(&dd->pcidev->dev, "Couldn't read "
- "linkerror%d of HT slave/primary block\n",
- i);
- else if (linkerr & 0xf0) {
- ipath_cdbg(VERBOSE, "HT linkerr%d bits 0x%x set, "
- "clearing\n", linkerr >> 4, i);
- /*
- * writing the linkerr bits that are set should
- * clear them
- */
- if (pci_write_config_byte(dd->pcidev, link_off,
- linkerr))
- ipath_dbg("Failed write to clear HT "
- "linkerror%d\n", i);
- if (pci_read_config_byte(dd->pcidev, link_off,
- &linkerr))
- dev_info(&dd->pcidev->dev,
- "Couldn't reread linkerror%d of "
- "HT slave/primary block\n", i);
- else if (linkerr & 0xf0)
- dev_info(&dd->pcidev->dev,
- "HT linkerror%d bits 0x%x "
- "couldn't be cleared\n",
- i, linkerr >> 4);
- }
- }
-}
-
-static int ipath_setup_ht_reset(struct ipath_devdata *dd)
-{
- ipath_dbg("No reset possible for HT-400\n");
- return 0;
-}
-
-#define HT_CAPABILITY_ID 0x08 /* HT capabilities not defined in kernel */
-#define HT_INTR_DISC_CONFIG 0x80 /* HT interrupt and discovery cap */
-#define HT_INTR_REG_INDEX 2 /* intconfig requires indirect accesses */
-
-/*
- * Bits 13-15 of command==0 is slave/primary block. Clear any HT CRC
- * errors. We only bother to do this at load time, because it's OK if
- * it happened before we were loaded (first time after boot/reset),
- * but any time after that, it's fatal anyway. Also need to not check
- * for for upper byte errors if we are in 8 bit mode, so figure out
- * our width. For now, at least, also complain if it's 8 bit.
- */
-static void slave_or_pri_blk(struct ipath_devdata *dd, struct pci_dev *pdev,
- int pos, u8 cap_type)
-{
- u8 linkwidth = 0, linkerr, link_a_b_off, link_off;
- u16 linkctrl = 0;
- int i;
-
- dd->ipath_ht_slave_off = pos;
- /* command word, master_host bit */
- /* master host || slave */
- if ((cap_type >> 2) & 1)
- link_a_b_off = 4;
- else
- link_a_b_off = 0;
- ipath_cdbg(VERBOSE, "HT%u (Link %c) connected to processor\n",
- link_a_b_off ? 1 : 0,
- link_a_b_off ? 'B' : 'A');
-
- link_a_b_off += pos;
-
- /*
- * check both link control registers; clear both HT CRC sets if
- * necessary.
- */
- for (i = 0; i < 2; i++) {
- link_off = pos + i * 4 + 0x4;
- if (pci_read_config_word(pdev, link_off, &linkctrl))
- ipath_dev_err(dd, "Couldn't read HT link control%d "
- "register\n", i);
- else if (linkctrl & (0xf << 8)) {
- ipath_cdbg(VERBOSE, "Clear linkctrl%d CRC Error "
- "bits %x\n", i, linkctrl & (0xf << 8));
- /*
- * now write them back to clear the error.
- */
- pci_write_config_byte(pdev, link_off,
- linkctrl & (0xf << 8));
- }
- }
-
- /*
- * As with HT CRC bits, same for protocol errors that might occur
- * during boot.
- */
- for (i = 0; i < 2; i++) {
- link_off = pos + i * 4 + 0xd;
- if (pci_read_config_byte(pdev, link_off, &linkerr))
- dev_info(&pdev->dev, "Couldn't read linkerror%d "
- "of HT slave/primary block\n", i);
- else if (linkerr & 0xf0) {
- ipath_cdbg(VERBOSE, "HT linkerr%d bits 0x%x set, "
- "clearing\n", linkerr >> 4, i);
- /*
- * writing the linkerr bits that are set will clear
- * them
- */
- if (pci_write_config_byte
- (pdev, link_off, linkerr))
- ipath_dbg("Failed write to clear HT "
- "linkerror%d\n", i);
- if (pci_read_config_byte(pdev, link_off, &linkerr))
- dev_info(&pdev->dev, "Couldn't reread "
- "linkerror%d of HT slave/primary "
- "block\n", i);
- else if (linkerr & 0xf0)
- dev_info(&pdev->dev, "HT linkerror%d bits "
- "0x%x couldn't be cleared\n",
- i, linkerr >> 4);
- }
- }
-
- /*
- * this is just for our link to the host, not devices connected
- * through tunnel.
- */
-
- if (pci_read_config_byte(pdev, link_a_b_off + 7, &linkwidth))
- ipath_dev_err(dd, "Couldn't read HT link width "
- "config register\n");
- else {
- u32 width;
- switch (linkwidth & 7) {
- case 5:
- width = 4;
- break;
- case 4:
- width = 2;
- break;
- case 3:
- width = 32;
- break;
- case 1:
- width = 16;
- break;
- case 0:
- default: /* if wrong, assume 8 bit */
- width = 8;
- break;
- }
-
- dd->ipath_htwidth = width;
-
- if (linkwidth != 0x11) {
- ipath_dev_err(dd, "Not configured for 16 bit HT "
- "(%x)\n", linkwidth);
- if (!(linkwidth & 0xf)) {
- ipath_dbg("Will ignore HT lane1 errors\n");
- dd->ipath_flags |= IPATH_8BIT_IN_HT0;
- }
- }
- }
-
- /*
- * this is just for our link to the host, not devices connected
- * through tunnel.
- */
- if (pci_read_config_byte(pdev, link_a_b_off + 0xd, &linkwidth))
- ipath_dev_err(dd, "Couldn't read HT link frequency "
- "config register\n");
- else {
- u32 speed;
- switch (linkwidth & 0xf) {
- case 6:
- speed = 1000;
- break;
- case 5:
- speed = 800;
- break;
- case 4:
- speed = 600;
- break;
- case 3:
- speed = 500;
- break;
- case 2:
- speed = 400;
- break;
- case 1:
- speed = 300;
- break;
- default:
- /*
- * assume reserved and vendor-specific are 200...
- */
- case 0:
- speed = 200;
- break;
- }
- dd->ipath_htspeed = speed;
- }
-}
-
-static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev,
- int pos)
-{
- u32 int_handler_addr_lower;
- u32 int_handler_addr_upper;
- u64 ihandler;
- u32 intvec;
-
- /* use indirection register to get the intr handler */
- pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x10);
- pci_read_config_dword(pdev, pos + 4, &int_handler_addr_lower);
- pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x11);
- pci_read_config_dword(pdev, pos + 4, &int_handler_addr_upper);
-
- ihandler = (u64) int_handler_addr_lower |
- ((u64) int_handler_addr_upper << 32);
-
- /*
- * kernels with CONFIG_PCI_MSI set the vector in the irq field of
- * struct pci_device, so we use that to program the HT-400 internal
- * interrupt register (not config space) with that value. The BIOS
- * must still have done the basic MSI setup.
- */
- intvec = pdev->irq;
- /*
- * clear any vector bits there; normally not set but we'll overload
- * this for some debug purposes (setting the HTC debug register
- * value from software, rather than GPIOs), so it might be set on a
- * driver reload.
- */
- ihandler &= ~0xff0000;
- /* x86 vector goes in intrinfo[23:16] */
- ihandler |= intvec << 16;
- ipath_cdbg(VERBOSE, "ihandler lower %x, upper %x, intvec %x, "
- "interruptconfig %llx\n", int_handler_addr_lower,
- int_handler_addr_upper, intvec,
- (unsigned long long) ihandler);
-
- /* can't program yet, so save for interrupt setup */
- dd->ipath_intconfig = ihandler;
- /* keep going, so we find link control stuff also */
-
- return ihandler != 0;
-}
-
-/**
- * ipath_setup_ht_config - setup the interruptconfig register
- * @dd: the infinipath device
- * @pdev: the PCI device
- *
- * setup the interruptconfig register from the HT config info.
- * Also clear CRC errors in HT linkcontrol, if necessary.
- * This is done only for the real hardware. It is done before
- * chip address space is initted, so can't touch infinipath registers
- */
-static int ipath_setup_ht_config(struct ipath_devdata *dd,
- struct pci_dev *pdev)
-{
- int pos, ret = 0;
- int ihandler = 0;
-
- /*
- * Read the capability info to find the interrupt info, and also
- * handle clearing CRC errors in linkctrl register if necessary. We
- * do this early, before we ever enable errors or hardware errors,
- * mostly to avoid causing the chip to enter freeze mode.
- */
- pos = pci_find_capability(pdev, HT_CAPABILITY_ID);
- if (!pos) {
- ipath_dev_err(dd, "Couldn't find HyperTransport "
- "capability; no interrupts\n");
- ret = -ENODEV;
- goto bail;
- }
- do {
- u8 cap_type;
-
- /* the HT capability type byte is 3 bytes after the
- * capability byte.
- */
- if (pci_read_config_byte(pdev, pos + 3, &cap_type)) {
- dev_info(&pdev->dev, "Couldn't read config "
- "command @ %d\n", pos);
- continue;
- }
- if (!(cap_type & 0xE0))
- slave_or_pri_blk(dd, pdev, pos, cap_type);
- else if (cap_type == HT_INTR_DISC_CONFIG)
- ihandler = set_int_handler(dd, pdev, pos);
- } while ((pos = pci_find_next_capability(pdev, pos,
- HT_CAPABILITY_ID)));
-
- if (!ihandler) {
- ipath_dev_err(dd, "Couldn't find interrupt handler in "
- "config space\n");
- ret = -ENODEV;
- }
-
-bail:
- return ret;
-}
-
-/**
- * ipath_setup_ht_cleanup - clean up any per-chip chip-specific stuff
- * @dd: the infinipath device
- *
- * Called during driver unload.
- * This is currently a nop for the HT-400, not for all chips
- */
-static void ipath_setup_ht_cleanup(struct ipath_devdata *dd)
-{
-}
-
-/**
- * ipath_setup_ht_setextled - set the state of the two external LEDs
- * @dd: the infinipath device
- * @lst: the L state
- * @ltst: the LT state
- *
- * Set the state of the two external LEDs, to indicate physical and
- * logical state of IB link. For this chip (at least with recommended
- * board pinouts), LED1 is Green (physical state), and LED2 is Yellow
- * (logical state)
- *
- * Note: We try to match the Mellanox HCA LED behavior as best
- * we can. Green indicates physical link state is OK (something is
- * plugged in, and we can train).
- * Amber indicates the link is logically up (ACTIVE).
- * Mellanox further blinks the amber LED to indicate data packet
- * activity, but we have no hardware support for that, so it would
- * require waking up every 10-20 msecs and checking the counters
- * on the chip, and then turning the LED off if appropriate. That's
- * visible overhead, so not something we will do.
- *
- */
-static void ipath_setup_ht_setextled(struct ipath_devdata *dd,
- u64 lst, u64 ltst)
-{
- u64 extctl;
-
- /* the diags use the LED to indicate diag info, so we leave
- * the external LED alone when the diags are running */
- if (ipath_diag_inuse)
- return;
-
- /*
- * start by setting both LED control bits to off, then turn
- * on the appropriate bit(s).
- */
- if (dd->ipath_boardrev == 8) { /* LS/X-1 uses different pins */
- /*
- * major difference is that INFINIPATH_EXTC_LEDGBLERR_OFF
- * is inverted, because it is normally used to indicate
- * a hardware fault at reset, if there were errors
- */
- extctl = (dd->ipath_extctrl & ~INFINIPATH_EXTC_LEDGBLOK_ON)
- | INFINIPATH_EXTC_LEDGBLERR_OFF;
- if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP)
- extctl &= ~INFINIPATH_EXTC_LEDGBLERR_OFF;
- if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
- extctl |= INFINIPATH_EXTC_LEDGBLOK_ON;
- }
- else {
- extctl = dd->ipath_extctrl &
- ~(INFINIPATH_EXTC_LED1PRIPORT_ON |
- INFINIPATH_EXTC_LED2PRIPORT_ON);
- if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP)
- extctl |= INFINIPATH_EXTC_LED1PRIPORT_ON;
- if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
- extctl |= INFINIPATH_EXTC_LED2PRIPORT_ON;
- }
- dd->ipath_extctrl = extctl;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, extctl);
-}
-
-static void ipath_init_ht_variables(void)
-{
- ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM;
- ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM;
- ipath_gpio_sda = IPATH_GPIO_SDA;
- ipath_gpio_scl = IPATH_GPIO_SCL;
-
- infinipath_i_bitsextant =
- (INFINIPATH_I_RCVURG_MASK << INFINIPATH_I_RCVURG_SHIFT) |
- (INFINIPATH_I_RCVAVAIL_MASK <<
- INFINIPATH_I_RCVAVAIL_SHIFT) |
- INFINIPATH_I_ERROR | INFINIPATH_I_SPIOSENT |
- INFINIPATH_I_SPIOBUFAVAIL | INFINIPATH_I_GPIO;
-
- infinipath_e_bitsextant =
- INFINIPATH_E_RFORMATERR | INFINIPATH_E_RVCRC |
- INFINIPATH_E_RICRC | INFINIPATH_E_RMINPKTLEN |
- INFINIPATH_E_RMAXPKTLEN | INFINIPATH_E_RLONGPKTLEN |
- INFINIPATH_E_RSHORTPKTLEN | INFINIPATH_E_RUNEXPCHAR |
- INFINIPATH_E_RUNSUPVL | INFINIPATH_E_REBP |
- INFINIPATH_E_RIBFLOW | INFINIPATH_E_RBADVERSION |
- INFINIPATH_E_RRCVEGRFULL | INFINIPATH_E_RRCVHDRFULL |
- INFINIPATH_E_RBADTID | INFINIPATH_E_RHDRLEN |
- INFINIPATH_E_RHDR | INFINIPATH_E_RIBLOSTLINK |
- INFINIPATH_E_SMINPKTLEN | INFINIPATH_E_SMAXPKTLEN |
- INFINIPATH_E_SUNDERRUN | INFINIPATH_E_SPKTLEN |
- INFINIPATH_E_SDROPPEDSMPPKT | INFINIPATH_E_SDROPPEDDATAPKT |
- INFINIPATH_E_SPIOARMLAUNCH | INFINIPATH_E_SUNEXPERRPKTNUM |
- INFINIPATH_E_SUNSUPVL | INFINIPATH_E_IBSTATUSCHANGED |
- INFINIPATH_E_INVALIDADDR | INFINIPATH_E_RESET |
- INFINIPATH_E_HARDWARE;
-
- infinipath_hwe_bitsextant =
- (INFINIPATH_HWE_HTCMEMPARITYERR_MASK <<
- INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT) |
- (INFINIPATH_HWE_TXEMEMPARITYERR_MASK <<
- INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) |
- (INFINIPATH_HWE_RXEMEMPARITYERR_MASK <<
- INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) |
- INFINIPATH_HWE_HTCLNKABYTE0CRCERR |
- INFINIPATH_HWE_HTCLNKABYTE1CRCERR |
- INFINIPATH_HWE_HTCLNKBBYTE0CRCERR |
- INFINIPATH_HWE_HTCLNKBBYTE1CRCERR |
- INFINIPATH_HWE_HTCMISCERR4 |
- INFINIPATH_HWE_HTCMISCERR5 | INFINIPATH_HWE_HTCMISCERR6 |
- INFINIPATH_HWE_HTCMISCERR7 |
- INFINIPATH_HWE_HTCBUSTREQPARITYERR |
- INFINIPATH_HWE_HTCBUSTRESPPARITYERR |
- INFINIPATH_HWE_HTCBUSIREQPARITYERR |
- INFINIPATH_HWE_RXDSYNCMEMPARITYERR |
- INFINIPATH_HWE_MEMBISTFAILED |
- INFINIPATH_HWE_COREPLL_FBSLIP |
- INFINIPATH_HWE_COREPLL_RFSLIP |
- INFINIPATH_HWE_HTBPLL_FBSLIP |
- INFINIPATH_HWE_HTBPLL_RFSLIP |
- INFINIPATH_HWE_HTAPLL_FBSLIP |
- INFINIPATH_HWE_HTAPLL_RFSLIP |
- INFINIPATH_HWE_SERDESPLLFAILED |
- INFINIPATH_HWE_IBCBUSTOSPCPARITYERR |
- INFINIPATH_HWE_IBCBUSFRSPCPARITYERR;
-
- infinipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK;
- infinipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK;
-}
-
-/**
- * ipath_ht_init_hwerrors - enable hardware errors
- * @dd: the infinipath device
- *
- * now that we have finished initializing everything that might reasonably
- * cause a hardware error, and cleared those errors bits as they occur,
- * we can enable hardware errors in the mask (potentially enabling
- * freeze mode), and enable hardware errors as errors (along with
- * everything else) in errormask
- */
-static void ipath_ht_init_hwerrors(struct ipath_devdata *dd)
-{
- ipath_err_t val;
- u64 extsval;
-
- extsval = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
-
- if (!(extsval & INFINIPATH_EXTS_MEMBIST_ENDTEST))
- ipath_dev_err(dd, "MemBIST did not complete!\n");
-
- ipath_check_htlink(dd);
-
- /* barring bugs, all hwerrors become interrupts, which can */
- val = -1LL;
- /* don't look at crc lane1 if 8 bit */
- if (dd->ipath_flags & IPATH_8BIT_IN_HT0)
- val &= ~infinipath_hwe_htclnkabyte1crcerr;
- /* don't look at crc lane1 if 8 bit */
- if (dd->ipath_flags & IPATH_8BIT_IN_HT1)
- val &= ~infinipath_hwe_htclnkbbyte1crcerr;
-
- /*
- * disable RXDSYNCMEMPARITY because external serdes is unused,
- * and therefore the logic will never be used or initialized,
- * and uninitialized state will normally result in this error
- * being asserted. Similarly for the external serdess pll
- * lock signal.
- */
- val &= ~(INFINIPATH_HWE_SERDESPLLFAILED |
- INFINIPATH_HWE_RXDSYNCMEMPARITYERR);
-
- /*
- * Disable MISCERR4 because of an inversion in the HT core
- * logic checking for errors that cause this bit to be set.
- * The errata can also cause the protocol error bit to be set
- * in the HT config space linkerror register(s).
- */
- val &= ~INFINIPATH_HWE_HTCMISCERR4;
-
- /*
- * PLL ignored because MDIO interface has a logic problem
- * for reads, on Comstock and Ponderosa. BRINGUP
- */
- if (dd->ipath_boardrev == 4 || dd->ipath_boardrev == 9)
- val &= ~INFINIPATH_HWE_SERDESPLLFAILED;
- dd->ipath_hwerrmask = val;
-}
-
-/**
- * ipath_ht_bringup_serdes - bring up the serdes
- * @dd: the infinipath device
- */
-static int ipath_ht_bringup_serdes(struct ipath_devdata *dd)
-{
- u64 val, config1;
- int ret = 0, change = 0;
-
- ipath_dbg("Trying to bringup serdes\n");
-
- if (ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus) &
- INFINIPATH_HWE_SERDESPLLFAILED)
- {
- ipath_dbg("At start, serdes PLL failed bit set in "
- "hwerrstatus, clearing and continuing\n");
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
- INFINIPATH_HWE_SERDESPLLFAILED);
- }
-
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
- config1 = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig1);
-
- ipath_cdbg(VERBOSE, "Initial serdes status is config0=%llx "
- "config1=%llx, sstatus=%llx xgxs %llx\n",
- (unsigned long long) val, (unsigned long long) config1,
- (unsigned long long)
- ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesstatus),
- (unsigned long long)
- ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
-
- /* force reset on */
- val |= INFINIPATH_SERDC0_RESET_PLL
- /* | INFINIPATH_SERDC0_RESET_MASK */
- ;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
- udelay(15); /* need pll reset set at least for a bit */
-
- if (val & INFINIPATH_SERDC0_RESET_PLL) {
- u64 val2 = val &= ~INFINIPATH_SERDC0_RESET_PLL;
- /* set lane resets, and tx idle, during pll reset */
- val2 |= INFINIPATH_SERDC0_RESET_MASK |
- INFINIPATH_SERDC0_TXIDLE;
- ipath_cdbg(VERBOSE, "Clearing serdes PLL reset (writing "
- "%llx)\n", (unsigned long long) val2);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0,
- val2);
- /*
- * be sure chip saw it
- */
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
- /*
- * need pll reset clear at least 11 usec before lane
- * resets cleared; give it a few more
- */
- udelay(15);
- val = val2; /* for check below */
- }
-
- if (val & (INFINIPATH_SERDC0_RESET_PLL |
- INFINIPATH_SERDC0_RESET_MASK |
- INFINIPATH_SERDC0_TXIDLE)) {
- val &= ~(INFINIPATH_SERDC0_RESET_PLL |
- INFINIPATH_SERDC0_RESET_MASK |
- INFINIPATH_SERDC0_TXIDLE);
- /* clear them */
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0,
- val);
- }
-
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
- if (((val >> INFINIPATH_XGXS_MDIOADDR_SHIFT) &
- INFINIPATH_XGXS_MDIOADDR_MASK) != 3) {
- val &= ~(INFINIPATH_XGXS_MDIOADDR_MASK <<
- INFINIPATH_XGXS_MDIOADDR_SHIFT);
- /*
- * we use address 3
- */
- val |= 3ULL << INFINIPATH_XGXS_MDIOADDR_SHIFT;
- change = 1;
- }
- if (val & INFINIPATH_XGXS_RESET) {
- /* normally true after boot */
- val &= ~INFINIPATH_XGXS_RESET;
- change = 1;
- }
- if (change)
- ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
-
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
-
- /* clear current and de-emphasis bits */
- config1 &= ~0x0ffffffff00ULL;
- /* set current to 20ma */
- config1 |= 0x00000000000ULL;
- /* set de-emphasis to -5.68dB */
- config1 |= 0x0cccc000000ULL;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig1, config1);
-
- ipath_cdbg(VERBOSE, "After setup: serdes status is config0=%llx "
- "config1=%llx, sstatus=%llx xgxs %llx\n",
- (unsigned long long) val, (unsigned long long) config1,
- (unsigned long long)
- ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesstatus),
- (unsigned long long)
- ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
-
- if (!ipath_waitfor_mdio_cmdready(dd)) {
- ipath_write_kreg(dd, dd->ipath_kregs->kr_mdio,
- ipath_mdio_req(IPATH_MDIO_CMD_READ, 31,
- IPATH_MDIO_CTRL_XGXS_REG_8,
- 0));
- if (ipath_waitfor_complete(dd, dd->ipath_kregs->kr_mdio,
- IPATH_MDIO_DATAVALID, &val))
- ipath_dbg("Never got MDIO data for XGXS status "
- "read\n");
- else
- ipath_cdbg(VERBOSE, "MDIO Read reg8, "
- "'bank' 31 %x\n", (u32) val);
- } else
- ipath_dbg("Never got MDIO cmdready for XGXS status read\n");
-
- return ret; /* for now, say we always succeeded */
-}
-
-/**
- * ipath_ht_quiet_serdes - set serdes to txidle
- * @dd: the infinipath device
- * driver is being unloaded
- */
-static void ipath_ht_quiet_serdes(struct ipath_devdata *dd)
-{
- u64 val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
-
- val |= INFINIPATH_SERDC0_TXIDLE;
- ipath_dbg("Setting TxIdleEn on serdes (config0 = %llx)\n",
- (unsigned long long) val);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
-}
-
-static int ipath_ht_intconfig(struct ipath_devdata *dd)
-{
- int ret;
-
- if (!dd->ipath_intconfig) {
- ipath_dev_err(dd, "No interrupts enabled, couldn't setup "
- "interrupt address\n");
- ret = 1;
- goto bail;
- }
-
- ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig,
- dd->ipath_intconfig); /* interrupt address */
- ret = 0;
-
-bail:
- return ret;
-}
-
-/**
- * ipath_pe_put_tid - write a TID in chip
- * @dd: the infinipath device
- * @tidptr: pointer to the expected TID (in chip) to udpate
- * @tidtype: 0 for eager, 1 for expected
- * @pa: physical address of in memory buffer; ipath_tidinvalid if freeing
- *
- * This exists as a separate routine to allow for special locking etc.
- * It's used for both the full cleanup on exit, as well as the normal
- * setup and teardown.
- */
-static void ipath_ht_put_tid(struct ipath_devdata *dd,
- u64 __iomem *tidptr, u32 type,
- unsigned long pa)
-{
- if (pa != dd->ipath_tidinvalid) {
- if (unlikely((pa & ~INFINIPATH_RT_ADDR_MASK))) {
- dev_info(&dd->pcidev->dev,
- "physaddr %lx has more than "
- "40 bits, using only 40!!!\n", pa);
- pa &= INFINIPATH_RT_ADDR_MASK;
- }
- if (type == 0)
- pa |= dd->ipath_tidtemplate;
- else {
- /* in words (fixed, full page). */
- u64 lenvalid = PAGE_SIZE >> 2;
- lenvalid <<= INFINIPATH_RT_BUFSIZE_SHIFT;
- pa |= lenvalid | INFINIPATH_RT_VALID;
- }
- }
- if (dd->ipath_kregbase)
- writeq(pa, tidptr);
-}
-
-/**
- * ipath_ht_clear_tid - clear all TID entries for a port, expected and eager
- * @dd: the infinipath device
- * @port: the port
- *
- * Used from ipath_close(), and at chip initialization.
- */
-static void ipath_ht_clear_tids(struct ipath_devdata *dd, unsigned port)
-{
- u64 __iomem *tidbase;
- int i;
-
- if (!dd->ipath_kregbase)
- return;
-
- ipath_cdbg(VERBOSE, "Invalidate TIDs for port %u\n", port);
-
- /*
- * need to invalidate all of the expected TID entries for this
- * port, so we don't have valid entries that might somehow get
- * used (early in next use of this port, or through some bug)
- */
- tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) +
- dd->ipath_rcvtidbase +
- port * dd->ipath_rcvtidcnt *
- sizeof(*tidbase));
- for (i = 0; i < dd->ipath_rcvtidcnt; i++)
- ipath_ht_put_tid(dd, &tidbase[i], 1, dd->ipath_tidinvalid);
-
- tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) +
- dd->ipath_rcvegrbase +
- port * dd->ipath_rcvegrcnt *
- sizeof(*tidbase));
-
- for (i = 0; i < dd->ipath_rcvegrcnt; i++)
- ipath_ht_put_tid(dd, &tidbase[i], 0, dd->ipath_tidinvalid);
-}
-
-/**
- * ipath_ht_tidtemplate - setup constants for TID updates
- * @dd: the infinipath device
- *
- * We setup stuff that we use a lot, to avoid calculating each time
- */
-static void ipath_ht_tidtemplate(struct ipath_devdata *dd)
-{
- dd->ipath_tidtemplate = dd->ipath_ibmaxlen >> 2;
- dd->ipath_tidtemplate <<= INFINIPATH_RT_BUFSIZE_SHIFT;
- dd->ipath_tidtemplate |= INFINIPATH_RT_VALID;
-
- /*
- * work around chip errata bug 7358, by marking invalid tids
- * as having max length
- */
- dd->ipath_tidinvalid = (-1LL & INFINIPATH_RT_BUFSIZE_MASK) <<
- INFINIPATH_RT_BUFSIZE_SHIFT;
-}
-
-static int ipath_ht_early_init(struct ipath_devdata *dd)
-{
- u32 __iomem *piobuf;
- u32 pioincr, val32, egrsize;
- int i;
-
- /*
- * one cache line; long IB headers will spill over into received
- * buffer
- */
- dd->ipath_rcvhdrentsize = 16;
- dd->ipath_rcvhdrsize = IPATH_DFLT_RCVHDRSIZE;
-
- /*
- * For HT-400, we allocate a somewhat overly large eager buffer,
- * such that we can guarantee that we can receive the largest
- * packet that we can send out. To truly support a 4KB MTU,
- * we need to bump this to a large value. To date, other than
- * testing, we have never encountered an HCA that can really
- * send 4KB MTU packets, so we do not handle that (we'll get
- * errors interrupts if we ever see one).
- */
- dd->ipath_rcvegrbufsize = dd->ipath_piosize2k;
- egrsize = dd->ipath_rcvegrbufsize;
-
- /*
- * the min() check here is currently a nop, but it may not
- * always be, depending on just how we do ipath_rcvegrbufsize
- */
- dd->ipath_ibmaxlen = min(dd->ipath_piosize2k,
- dd->ipath_rcvegrbufsize);
- dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen;
- ipath_ht_tidtemplate(dd);
-
- /*
- * zero all the TID entries at startup. We do this for sanity,
- * in case of a previous driver crash of some kind, and also
- * because the chip powers up with these memories in an unknown
- * state. Use portcnt, not cfgports, since this is for the
- * full chip, not for current (possibly different) configuration
- * value.
- * Chip Errata bug 6447
- */
- for (val32 = 0; val32 < dd->ipath_portcnt; val32++)
- ipath_ht_clear_tids(dd, val32);
-
- /*
- * write the pbc of each buffer, to be sure it's initialized, then
- * cancel all the buffers, and also abort any packets that might
- * have been in flight for some reason (the latter is for driver
- * unload/reload, but isn't a bad idea at first init). PIO send
- * isn't enabled at this point, so there is no danger of sending
- * these out on the wire.
- * Chip Errata bug 6610
- */
- piobuf = (u32 __iomem *) (((char __iomem *)(dd->ipath_kregbase)) +
- dd->ipath_piobufbase);
- pioincr = dd->ipath_palign / sizeof(*piobuf);
- for (i = 0; i < dd->ipath_piobcnt2k; i++) {
- /*
- * reasonable word count, just to init pbc
- */
- writel(16, piobuf);
- piobuf += pioincr;
- }
- /*
- * self-clearing
- */
- ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
- INFINIPATH_S_ABORT);
-
- ipath_get_eeprom_info(dd);
- if(dd->ipath_boardrev == 5 && dd->ipath_serial[0] == '1' &&
- dd->ipath_serial[1] == '2' && dd->ipath_serial[2] == '8') {
- /*
- * Later production HT-460 has same changes as HT-465, so
- * can use GPIO interrupts. They have serial #'s starting
- * with 128, rather than 112.
- */
- dd->ipath_flags |= IPATH_GPIO_INTR;
- dd->ipath_flags &= ~IPATH_POLL_RX_INTR;
- }
- return 0;
-}
-
-/**
- * ipath_init_ht_get_base_info - set chip-specific flags for user code
- * @dd: the infinipath device
- * @kbase: ipath_base_info pointer
- *
- * We set the PCIE flag because the lower bandwidth on PCIe vs
- * HyperTransport can affect some user packet algorithims.
- */
-static int ipath_ht_get_base_info(struct ipath_portdata *pd, void *kbase)
-{
- struct ipath_base_info *kinfo = kbase;
-
- kinfo->spi_runtime_flags |= IPATH_RUNTIME_HT |
- IPATH_RUNTIME_RCVHDR_COPY;
-
- return 0;
-}
-
-/**
- * ipath_init_ht400_funcs - set up the chip-specific function pointers
- * @dd: the infinipath device
- *
- * This is global, and is called directly at init to set up the
- * chip-specific function pointers for later use.
- */
-void ipath_init_ht400_funcs(struct ipath_devdata *dd)
-{
- dd->ipath_f_intrsetup = ipath_ht_intconfig;
- dd->ipath_f_bus = ipath_setup_ht_config;
- dd->ipath_f_reset = ipath_setup_ht_reset;
- dd->ipath_f_get_boardname = ipath_ht_boardname;
- dd->ipath_f_init_hwerrors = ipath_ht_init_hwerrors;
- dd->ipath_f_early_init = ipath_ht_early_init;
- dd->ipath_f_handle_hwerrors = ipath_ht_handle_hwerrors;
- dd->ipath_f_quiet_serdes = ipath_ht_quiet_serdes;
- dd->ipath_f_bringup_serdes = ipath_ht_bringup_serdes;
- dd->ipath_f_clear_tids = ipath_ht_clear_tids;
- dd->ipath_f_put_tid = ipath_ht_put_tid;
- dd->ipath_f_cleanup = ipath_setup_ht_cleanup;
- dd->ipath_f_setextled = ipath_setup_ht_setextled;
- dd->ipath_f_get_base_info = ipath_ht_get_base_info;
-
- /*
- * initialize chip-specific variables
- */
- dd->ipath_f_tidtemplate = ipath_ht_tidtemplate;
-
- /*
- * setup the register offsets, since they are different for each
- * chip
- */
- dd->ipath_kregs = &ipath_ht_kregs;
- dd->ipath_cregs = &ipath_ht_cregs;
-
- /*
- * do very early init that is needed before ipath_f_bus is
- * called
- */
- ipath_init_ht_variables();
-}
--- /dev/null
+/*
+ * Copyright (c) 2006 QLogic, Inc. All rights reserved.
+ * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the
+ * OpenIB.org BSD license below:
+ *
+ * Redistribution and use in source and binary forms, with or
+ * without modification, are permitted provided that the following
+ * conditions are met:
+ *
+ * - Redistributions of source code must retain the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer.
+ *
+ * - Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials
+ * provided with the distribution.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
+ * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
+ * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+ * SOFTWARE.
+ */
+
+/*
+ * This file contains all of the code that is specific to the InfiniPath
+ * HT chip.
+ */
+
+#include <linux/pci.h>
+#include <linux/delay.h>
+
+#include "ipath_kernel.h"
+#include "ipath_registers.h"
+
+/*
+ * This lists the InfiniPath registers, in the actual chip layout.
+ * This structure should never be directly accessed.
+ *
+ * The names are in InterCap form because they're taken straight from
+ * the chip specification. Since they're only used in this file, they
+ * don't pollute the rest of the source.
+*/
+
+struct _infinipath_do_not_use_kernel_regs {
+ unsigned long long Revision;
+ unsigned long long Control;
+ unsigned long long PageAlign;
+ unsigned long long PortCnt;
+ unsigned long long DebugPortSelect;
+ unsigned long long DebugPort;
+ unsigned long long SendRegBase;
+ unsigned long long UserRegBase;
+ unsigned long long CounterRegBase;
+ unsigned long long Scratch;
+ unsigned long long ReservedMisc1;
+ unsigned long long InterruptConfig;
+ unsigned long long IntBlocked;
+ unsigned long long IntMask;
+ unsigned long long IntStatus;
+ unsigned long long IntClear;
+ unsigned long long ErrorMask;
+ unsigned long long ErrorStatus;
+ unsigned long long ErrorClear;
+ unsigned long long HwErrMask;
+ unsigned long long HwErrStatus;
+ unsigned long long HwErrClear;
+ unsigned long long HwDiagCtrl;
+ unsigned long long MDIO;
+ unsigned long long IBCStatus;
+ unsigned long long IBCCtrl;
+ unsigned long long ExtStatus;
+ unsigned long long ExtCtrl;
+ unsigned long long GPIOOut;
+ unsigned long long GPIOMask;
+ unsigned long long GPIOStatus;
+ unsigned long long GPIOClear;
+ unsigned long long RcvCtrl;
+ unsigned long long RcvBTHQP;
+ unsigned long long RcvHdrSize;
+ unsigned long long RcvHdrCnt;
+ unsigned long long RcvHdrEntSize;
+ unsigned long long RcvTIDBase;
+ unsigned long long RcvTIDCnt;
+ unsigned long long RcvEgrBase;
+ unsigned long long RcvEgrCnt;
+ unsigned long long RcvBufBase;
+ unsigned long long RcvBufSize;
+ unsigned long long RxIntMemBase;
+ unsigned long long RxIntMemSize;
+ unsigned long long RcvPartitionKey;
+ unsigned long long ReservedRcv[10];
+ unsigned long long SendCtrl;
+ unsigned long long SendPIOBufBase;
+ unsigned long long SendPIOSize;
+ unsigned long long SendPIOBufCnt;
+ unsigned long long SendPIOAvailAddr;
+ unsigned long long TxIntMemBase;
+ unsigned long long TxIntMemSize;
+ unsigned long long ReservedSend[9];
+ unsigned long long SendBufferError;
+ unsigned long long SendBufferErrorCONT1;
+ unsigned long long SendBufferErrorCONT2;
+ unsigned long long SendBufferErrorCONT3;
+ unsigned long long ReservedSBE[4];
+ unsigned long long RcvHdrAddr0;
+ unsigned long long RcvHdrAddr1;
+ unsigned long long RcvHdrAddr2;
+ unsigned long long RcvHdrAddr3;
+ unsigned long long RcvHdrAddr4;
+ unsigned long long RcvHdrAddr5;
+ unsigned long long RcvHdrAddr6;
+ unsigned long long RcvHdrAddr7;
+ unsigned long long RcvHdrAddr8;
+ unsigned long long ReservedRHA[7];
+ unsigned long long RcvHdrTailAddr0;
+ unsigned long long RcvHdrTailAddr1;
+ unsigned long long RcvHdrTailAddr2;
+ unsigned long long RcvHdrTailAddr3;
+ unsigned long long RcvHdrTailAddr4;
+ unsigned long long RcvHdrTailAddr5;
+ unsigned long long RcvHdrTailAddr6;
+ unsigned long long RcvHdrTailAddr7;
+ unsigned long long RcvHdrTailAddr8;
+ unsigned long long ReservedRHTA[7];
+ unsigned long long Sync; /* Software only */
+ unsigned long long Dump; /* Software only */
+ unsigned long long SimVer; /* Software only */
+ unsigned long long ReservedSW[5];
+ unsigned long long SerdesConfig0;
+ unsigned long long SerdesConfig1;
+ unsigned long long SerdesStatus;
+ unsigned long long XGXSConfig;
+ unsigned long long ReservedSW2[4];
+};
+
+#define IPATH_KREG_OFFSET(field) (offsetof(struct \
+ _infinipath_do_not_use_kernel_regs, field) / sizeof(u64))
+#define IPATH_CREG_OFFSET(field) (offsetof( \
+ struct infinipath_counters, field) / sizeof(u64))
+
+static const struct ipath_kregs ipath_ht_kregs = {
+ .kr_control = IPATH_KREG_OFFSET(Control),
+ .kr_counterregbase = IPATH_KREG_OFFSET(CounterRegBase),
+ .kr_debugport = IPATH_KREG_OFFSET(DebugPort),
+ .kr_debugportselect = IPATH_KREG_OFFSET(DebugPortSelect),
+ .kr_errorclear = IPATH_KREG_OFFSET(ErrorClear),
+ .kr_errormask = IPATH_KREG_OFFSET(ErrorMask),
+ .kr_errorstatus = IPATH_KREG_OFFSET(ErrorStatus),
+ .kr_extctrl = IPATH_KREG_OFFSET(ExtCtrl),
+ .kr_extstatus = IPATH_KREG_OFFSET(ExtStatus),
+ .kr_gpio_clear = IPATH_KREG_OFFSET(GPIOClear),
+ .kr_gpio_mask = IPATH_KREG_OFFSET(GPIOMask),
+ .kr_gpio_out = IPATH_KREG_OFFSET(GPIOOut),
+ .kr_gpio_status = IPATH_KREG_OFFSET(GPIOStatus),
+ .kr_hwdiagctrl = IPATH_KREG_OFFSET(HwDiagCtrl),
+ .kr_hwerrclear = IPATH_KREG_OFFSET(HwErrClear),
+ .kr_hwerrmask = IPATH_KREG_OFFSET(HwErrMask),
+ .kr_hwerrstatus = IPATH_KREG_OFFSET(HwErrStatus),
+ .kr_ibcctrl = IPATH_KREG_OFFSET(IBCCtrl),
+ .kr_ibcstatus = IPATH_KREG_OFFSET(IBCStatus),
+ .kr_intblocked = IPATH_KREG_OFFSET(IntBlocked),
+ .kr_intclear = IPATH_KREG_OFFSET(IntClear),
+ .kr_interruptconfig = IPATH_KREG_OFFSET(InterruptConfig),
+ .kr_intmask = IPATH_KREG_OFFSET(IntMask),
+ .kr_intstatus = IPATH_KREG_OFFSET(IntStatus),
+ .kr_mdio = IPATH_KREG_OFFSET(MDIO),
+ .kr_pagealign = IPATH_KREG_OFFSET(PageAlign),
+ .kr_partitionkey = IPATH_KREG_OFFSET(RcvPartitionKey),
+ .kr_portcnt = IPATH_KREG_OFFSET(PortCnt),
+ .kr_rcvbthqp = IPATH_KREG_OFFSET(RcvBTHQP),
+ .kr_rcvbufbase = IPATH_KREG_OFFSET(RcvBufBase),
+ .kr_rcvbufsize = IPATH_KREG_OFFSET(RcvBufSize),
+ .kr_rcvctrl = IPATH_KREG_OFFSET(RcvCtrl),
+ .kr_rcvegrbase = IPATH_KREG_OFFSET(RcvEgrBase),
+ .kr_rcvegrcnt = IPATH_KREG_OFFSET(RcvEgrCnt),
+ .kr_rcvhdrcnt = IPATH_KREG_OFFSET(RcvHdrCnt),
+ .kr_rcvhdrentsize = IPATH_KREG_OFFSET(RcvHdrEntSize),
+ .kr_rcvhdrsize = IPATH_KREG_OFFSET(RcvHdrSize),
+ .kr_rcvintmembase = IPATH_KREG_OFFSET(RxIntMemBase),
+ .kr_rcvintmemsize = IPATH_KREG_OFFSET(RxIntMemSize),
+ .kr_rcvtidbase = IPATH_KREG_OFFSET(RcvTIDBase),
+ .kr_rcvtidcnt = IPATH_KREG_OFFSET(RcvTIDCnt),
+ .kr_revision = IPATH_KREG_OFFSET(Revision),
+ .kr_scratch = IPATH_KREG_OFFSET(Scratch),
+ .kr_sendbuffererror = IPATH_KREG_OFFSET(SendBufferError),
+ .kr_sendctrl = IPATH_KREG_OFFSET(SendCtrl),
+ .kr_sendpioavailaddr = IPATH_KREG_OFFSET(SendPIOAvailAddr),
+ .kr_sendpiobufbase = IPATH_KREG_OFFSET(SendPIOBufBase),
+ .kr_sendpiobufcnt = IPATH_KREG_OFFSET(SendPIOBufCnt),
+ .kr_sendpiosize = IPATH_KREG_OFFSET(SendPIOSize),
+ .kr_sendregbase = IPATH_KREG_OFFSET(SendRegBase),
+ .kr_txintmembase = IPATH_KREG_OFFSET(TxIntMemBase),
+ .kr_txintmemsize = IPATH_KREG_OFFSET(TxIntMemSize),
+ .kr_userregbase = IPATH_KREG_OFFSET(UserRegBase),
+ .kr_serdesconfig0 = IPATH_KREG_OFFSET(SerdesConfig0),
+ .kr_serdesconfig1 = IPATH_KREG_OFFSET(SerdesConfig1),
+ .kr_serdesstatus = IPATH_KREG_OFFSET(SerdesStatus),
+ .kr_xgxsconfig = IPATH_KREG_OFFSET(XGXSConfig),
+ /*
+ * These should not be used directly via ipath_read_kreg64(),
+ * use them with ipath_read_kreg64_port(),
+ */
+ .kr_rcvhdraddr = IPATH_KREG_OFFSET(RcvHdrAddr0),
+ .kr_rcvhdrtailaddr = IPATH_KREG_OFFSET(RcvHdrTailAddr0)
+};
+
+static const struct ipath_cregs ipath_ht_cregs = {
+ .cr_badformatcnt = IPATH_CREG_OFFSET(RxBadFormatCnt),
+ .cr_erricrccnt = IPATH_CREG_OFFSET(RxICRCErrCnt),
+ .cr_errlinkcnt = IPATH_CREG_OFFSET(RxLinkProblemCnt),
+ .cr_errlpcrccnt = IPATH_CREG_OFFSET(RxLPCRCErrCnt),
+ .cr_errpkey = IPATH_CREG_OFFSET(RxPKeyMismatchCnt),
+ .cr_errrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowCtrlErrCnt),
+ .cr_err_rlencnt = IPATH_CREG_OFFSET(RxLenErrCnt),
+ .cr_errslencnt = IPATH_CREG_OFFSET(TxLenErrCnt),
+ .cr_errtidfull = IPATH_CREG_OFFSET(RxTIDFullErrCnt),
+ .cr_errtidvalid = IPATH_CREG_OFFSET(RxTIDValidErrCnt),
+ .cr_errvcrccnt = IPATH_CREG_OFFSET(RxVCRCErrCnt),
+ .cr_ibstatuschange = IPATH_CREG_OFFSET(IBStatusChangeCnt),
+ /* calc from Reg_CounterRegBase + offset */
+ .cr_intcnt = IPATH_CREG_OFFSET(LBIntCnt),
+ .cr_invalidrlencnt = IPATH_CREG_OFFSET(RxMaxMinLenErrCnt),
+ .cr_invalidslencnt = IPATH_CREG_OFFSET(TxMaxMinLenErrCnt),
+ .cr_lbflowstallcnt = IPATH_CREG_OFFSET(LBFlowStallCnt),
+ .cr_pktrcvcnt = IPATH_CREG_OFFSET(RxDataPktCnt),
+ .cr_pktrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowPktCnt),
+ .cr_pktsendcnt = IPATH_CREG_OFFSET(TxDataPktCnt),
+ .cr_pktsendflowcnt = IPATH_CREG_OFFSET(TxFlowPktCnt),
+ .cr_portovflcnt = IPATH_CREG_OFFSET(RxP0HdrEgrOvflCnt),
+ .cr_rcvebpcnt = IPATH_CREG_OFFSET(RxEBPCnt),
+ .cr_rcvovflcnt = IPATH_CREG_OFFSET(RxBufOvflCnt),
+ .cr_senddropped = IPATH_CREG_OFFSET(TxDroppedPktCnt),
+ .cr_sendstallcnt = IPATH_CREG_OFFSET(TxFlowStallCnt),
+ .cr_sendunderruncnt = IPATH_CREG_OFFSET(TxUnderrunCnt),
+ .cr_wordrcvcnt = IPATH_CREG_OFFSET(RxDwordCnt),
+ .cr_wordsendcnt = IPATH_CREG_OFFSET(TxDwordCnt),
+ .cr_unsupvlcnt = IPATH_CREG_OFFSET(TxUnsupVLErrCnt),
+ .cr_rxdroppktcnt = IPATH_CREG_OFFSET(RxDroppedPktCnt),
+ .cr_iblinkerrrecovcnt = IPATH_CREG_OFFSET(IBLinkErrRecoveryCnt),
+ .cr_iblinkdowncnt = IPATH_CREG_OFFSET(IBLinkDownedCnt),
+ .cr_ibsymbolerrcnt = IPATH_CREG_OFFSET(IBSymbolErrCnt)
+};
+
+/* kr_intstatus, kr_intclear, kr_intmask bits */
+#define INFINIPATH_I_RCVURG_MASK 0x1FF
+#define INFINIPATH_I_RCVAVAIL_MASK 0x1FF
+
+/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */
+#define INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT 0
+#define INFINIPATH_HWE_HTCMEMPARITYERR_MASK 0x3FFFFFULL
+#define INFINIPATH_HWE_HTCLNKABYTE0CRCERR 0x0000000000800000ULL
+#define INFINIPATH_HWE_HTCLNKABYTE1CRCERR 0x0000000001000000ULL
+#define INFINIPATH_HWE_HTCLNKBBYTE0CRCERR 0x0000000002000000ULL
+#define INFINIPATH_HWE_HTCLNKBBYTE1CRCERR 0x0000000004000000ULL
+#define INFINIPATH_HWE_HTCMISCERR4 0x0000000008000000ULL
+#define INFINIPATH_HWE_HTCMISCERR5 0x0000000010000000ULL
+#define INFINIPATH_HWE_HTCMISCERR6 0x0000000020000000ULL
+#define INFINIPATH_HWE_HTCMISCERR7 0x0000000040000000ULL
+#define INFINIPATH_HWE_HTCBUSTREQPARITYERR 0x0000000080000000ULL
+#define INFINIPATH_HWE_HTCBUSTRESPPARITYERR 0x0000000100000000ULL
+#define INFINIPATH_HWE_HTCBUSIREQPARITYERR 0x0000000200000000ULL
+#define INFINIPATH_HWE_COREPLL_FBSLIP 0x0080000000000000ULL
+#define INFINIPATH_HWE_COREPLL_RFSLIP 0x0100000000000000ULL
+#define INFINIPATH_HWE_HTBPLL_FBSLIP 0x0200000000000000ULL
+#define INFINIPATH_HWE_HTBPLL_RFSLIP 0x0400000000000000ULL
+#define INFINIPATH_HWE_HTAPLL_FBSLIP 0x0800000000000000ULL
+#define INFINIPATH_HWE_HTAPLL_RFSLIP 0x1000000000000000ULL
+#define INFINIPATH_HWE_SERDESPLLFAILED 0x2000000000000000ULL
+
+/* kr_extstatus bits */
+#define INFINIPATH_EXTS_FREQSEL 0x2
+#define INFINIPATH_EXTS_SERDESSEL 0x4
+#define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000
+#define INFINIPATH_EXTS_MEMBIST_CORRECT 0x0000000000008000
+
+/*
+ * masks and bits that are different in different chips, or present only
+ * in one
+ */
+static const ipath_err_t infinipath_hwe_htcmemparityerr_mask =
+ INFINIPATH_HWE_HTCMEMPARITYERR_MASK;
+static const ipath_err_t infinipath_hwe_htcmemparityerr_shift =
+ INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT;
+
+static const ipath_err_t infinipath_hwe_htclnkabyte0crcerr =
+ INFINIPATH_HWE_HTCLNKABYTE0CRCERR;
+static const ipath_err_t infinipath_hwe_htclnkabyte1crcerr =
+ INFINIPATH_HWE_HTCLNKABYTE1CRCERR;
+static const ipath_err_t infinipath_hwe_htclnkbbyte0crcerr =
+ INFINIPATH_HWE_HTCLNKBBYTE0CRCERR;
+static const ipath_err_t infinipath_hwe_htclnkbbyte1crcerr =
+ INFINIPATH_HWE_HTCLNKBBYTE1CRCERR;
+
+#define _IPATH_GPIO_SDA_NUM 1
+#define _IPATH_GPIO_SCL_NUM 0
+
+#define IPATH_GPIO_SDA \
+ (1ULL << (_IPATH_GPIO_SDA_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
+#define IPATH_GPIO_SCL \
+ (1ULL << (_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
+
+/* keep the code below somewhat more readonable; not used elsewhere */
+#define _IPATH_HTLINK0_CRCBITS (infinipath_hwe_htclnkabyte0crcerr | \
+ infinipath_hwe_htclnkabyte1crcerr)
+#define _IPATH_HTLINK1_CRCBITS (infinipath_hwe_htclnkbbyte0crcerr | \
+ infinipath_hwe_htclnkbbyte1crcerr)
+#define _IPATH_HTLANE0_CRCBITS (infinipath_hwe_htclnkabyte0crcerr | \
+ infinipath_hwe_htclnkbbyte0crcerr)
+#define _IPATH_HTLANE1_CRCBITS (infinipath_hwe_htclnkabyte1crcerr | \
+ infinipath_hwe_htclnkbbyte1crcerr)
+
+static void hwerr_crcbits(struct ipath_devdata *dd, ipath_err_t hwerrs,
+ char *msg, size_t msgl)
+{
+ char bitsmsg[64];
+ ipath_err_t crcbits = hwerrs &
+ (_IPATH_HTLINK0_CRCBITS | _IPATH_HTLINK1_CRCBITS);
+ /* don't check if 8bit HT */
+ if (dd->ipath_flags & IPATH_8BIT_IN_HT0)
+ crcbits &= ~infinipath_hwe_htclnkabyte1crcerr;
+ /* don't check if 8bit HT */
+ if (dd->ipath_flags & IPATH_8BIT_IN_HT1)
+ crcbits &= ~infinipath_hwe_htclnkbbyte1crcerr;
+ /*
+ * we'll want to ignore link errors on link that is
+ * not in use, if any. For now, complain about both
+ */
+ if (crcbits) {
+ u16 ctrl0, ctrl1;
+ snprintf(bitsmsg, sizeof bitsmsg,
+ "[HT%s lane %s CRC (%llx); ignore till reload]",
+ !(crcbits & _IPATH_HTLINK1_CRCBITS) ?
+ "0 (A)" : (!(crcbits & _IPATH_HTLINK0_CRCBITS)
+ ? "1 (B)" : "0+1 (A+B)"),
+ !(crcbits & _IPATH_HTLANE1_CRCBITS) ? "0"
+ : (!(crcbits & _IPATH_HTLANE0_CRCBITS) ? "1" :
+ "0+1"), (unsigned long long) crcbits);
+ strlcat(msg, bitsmsg, msgl);
+
+ /*
+ * print extra info for debugging. slave/primary
+ * config word 4, 8 (link control 0, 1)
+ */
+
+ if (pci_read_config_word(dd->pcidev,
+ dd->ipath_ht_slave_off + 0x4,
+ &ctrl0))
+ dev_info(&dd->pcidev->dev, "Couldn't read "
+ "linkctrl0 of slave/primary "
+ "config block\n");
+ else if (!(ctrl0 & 1 << 6))
+ /* not if EOC bit set */
+ ipath_dbg("HT linkctrl0 0x%x%s%s\n", ctrl0,
+ ((ctrl0 >> 8) & 7) ? " CRC" : "",
+ ((ctrl0 >> 4) & 1) ? "linkfail" :
+ "");
+ if (pci_read_config_word(dd->pcidev,
+ dd->ipath_ht_slave_off + 0x8,
+ &ctrl1))
+ dev_info(&dd->pcidev->dev, "Couldn't read "
+ "linkctrl1 of slave/primary "
+ "config block\n");
+ else if (!(ctrl1 & 1 << 6))
+ /* not if EOC bit set */
+ ipath_dbg("HT linkctrl1 0x%x%s%s\n", ctrl1,
+ ((ctrl1 >> 8) & 7) ? " CRC" : "",
+ ((ctrl1 >> 4) & 1) ? "linkfail" :
+ "");
+
+ /* disable until driver reloaded */
+ dd->ipath_hwerrmask &= ~crcbits;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
+ dd->ipath_hwerrmask);
+ ipath_dbg("HT crc errs: %s\n", msg);
+ } else
+ ipath_dbg("ignoring HT crc errors 0x%llx, "
+ "not in use\n", (unsigned long long)
+ (hwerrs & (_IPATH_HTLINK0_CRCBITS |
+ _IPATH_HTLINK1_CRCBITS)));
+}
+
+/**
+ * ipath_ht_handle_hwerrors - display hardware errors
+ * @dd: the infinipath device
+ * @msg: the output buffer
+ * @msgl: the size of the output buffer
+ *
+ * Use same msg buffer as regular errors to avoid
+ * excessive stack use. Most hardware errors are catastrophic, but for
+ * right now, we'll print them and continue.
+ * We reuse the same message buffer as ipath_handle_errors() to avoid
+ * excessive stack usage.
+ */
+static void ipath_ht_handle_hwerrors(struct ipath_devdata *dd, char *msg,
+ size_t msgl)
+{
+ ipath_err_t hwerrs;
+ u32 bits, ctrl;
+ int isfatal = 0;
+ char bitsmsg[64];
+
+ hwerrs = ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus);
+
+ if (!hwerrs) {
+ ipath_cdbg(VERBOSE, "Called but no hardware errors set\n");
+ /*
+ * better than printing cofusing messages
+ * This seems to be related to clearing the crc error, or
+ * the pll error during init.
+ */
+ goto bail;
+ } else if (hwerrs == -1LL) {
+ ipath_dev_err(dd, "Read of hardware error status failed "
+ "(all bits set); ignoring\n");
+ goto bail;
+ }
+ ipath_stats.sps_hwerrs++;
+
+ /* Always clear the error status register, except MEMBISTFAIL,
+ * regardless of whether we continue or stop using the chip.
+ * We want that set so we know it failed, even across driver reload.
+ * We'll still ignore it in the hwerrmask. We do this partly for
+ * diagnostics, but also for support */
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
+ hwerrs&~INFINIPATH_HWE_MEMBISTFAILED);
+
+ hwerrs &= dd->ipath_hwerrmask;
+
+ /*
+ * make sure we get this much out, unless told to be quiet,
+ * or it's occurred within the last 5 seconds
+ */
+ if ((hwerrs & ~dd->ipath_lasthwerror) ||
+ (ipath_debug & __IPATH_VERBDBG))
+ dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx "
+ "(cleared)\n", (unsigned long long) hwerrs);
+ dd->ipath_lasthwerror |= hwerrs;
+
+ if (hwerrs & ~infinipath_hwe_bitsextant)
+ ipath_dev_err(dd, "hwerror interrupt with unknown errors "
+ "%llx set\n", (unsigned long long)
+ (hwerrs & ~infinipath_hwe_bitsextant));
+
+ ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control);
+ if (ctrl & INFINIPATH_C_FREEZEMODE) {
+ if (hwerrs) {
+ /*
+ * if any set that we aren't ignoring; only
+ * make the complaint once, in case it's stuck
+ * or recurring, and we get here multiple
+ * times.
+ */
+ if (dd->ipath_flags & IPATH_INITTED) {
+ ipath_dev_err(dd, "Fatal Error (freeze "
+ "mode), no longer usable\n");
+ isfatal = 1;
+ }
+ *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY;
+ /* mark as having had error */
+ *dd->ipath_statusp |= IPATH_STATUS_HWERROR;
+ /*
+ * mark as not usable, at a minimum until driver
+ * is reloaded, probably until reboot, since no
+ * other reset is possible.
+ */
+ dd->ipath_flags &= ~IPATH_INITTED;
+ } else {
+ ipath_dbg("Clearing freezemode on ignored hardware "
+ "error\n");
+ ctrl &= ~INFINIPATH_C_FREEZEMODE;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
+ ctrl);
+ }
+ }
+
+ *msg = '\0';
+
+ /*
+ * may someday want to decode into which bits are which
+ * functional area for parity errors, etc.
+ */
+ if (hwerrs & (infinipath_hwe_htcmemparityerr_mask
+ << INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT)) {
+ bits = (u32) ((hwerrs >>
+ INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT) &
+ INFINIPATH_HWE_HTCMEMPARITYERR_MASK);
+ snprintf(bitsmsg, sizeof bitsmsg, "[HTC Parity Errs %x] ",
+ bits);
+ strlcat(msg, bitsmsg, msgl);
+ }
+ if (hwerrs & (INFINIPATH_HWE_RXEMEMPARITYERR_MASK
+ << INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT)) {
+ bits = (u32) ((hwerrs >>
+ INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) &
+ INFINIPATH_HWE_RXEMEMPARITYERR_MASK);
+ snprintf(bitsmsg, sizeof bitsmsg, "[RXE Parity Errs %x] ",
+ bits);
+ strlcat(msg, bitsmsg, msgl);
+ }
+ if (hwerrs & (INFINIPATH_HWE_TXEMEMPARITYERR_MASK
+ << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)) {
+ bits = (u32) ((hwerrs >>
+ INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) &
+ INFINIPATH_HWE_TXEMEMPARITYERR_MASK);
+ snprintf(bitsmsg, sizeof bitsmsg, "[TXE Parity Errs %x] ",
+ bits);
+ strlcat(msg, bitsmsg, msgl);
+ }
+ if (hwerrs & INFINIPATH_HWE_IBCBUSTOSPCPARITYERR)
+ strlcat(msg, "[IB2IPATH Parity]", msgl);
+ if (hwerrs & INFINIPATH_HWE_IBCBUSFRSPCPARITYERR)
+ strlcat(msg, "[IPATH2IB Parity]", msgl);
+ if (hwerrs & INFINIPATH_HWE_HTCBUSIREQPARITYERR)
+ strlcat(msg, "[HTC Ireq Parity]", msgl);
+ if (hwerrs & INFINIPATH_HWE_HTCBUSTREQPARITYERR)
+ strlcat(msg, "[HTC Treq Parity]", msgl);
+ if (hwerrs & INFINIPATH_HWE_HTCBUSTRESPPARITYERR)
+ strlcat(msg, "[HTC Tresp Parity]", msgl);
+
+ if (hwerrs & (_IPATH_HTLINK0_CRCBITS | _IPATH_HTLINK1_CRCBITS))
+ hwerr_crcbits(dd, hwerrs, msg, msgl);
+
+ if (hwerrs & INFINIPATH_HWE_HTCMISCERR5)
+ strlcat(msg, "[HT core Misc5]", msgl);
+ if (hwerrs & INFINIPATH_HWE_HTCMISCERR6)
+ strlcat(msg, "[HT core Misc6]", msgl);
+ if (hwerrs & INFINIPATH_HWE_HTCMISCERR7)
+ strlcat(msg, "[HT core Misc7]", msgl);
+ if (hwerrs & INFINIPATH_HWE_MEMBISTFAILED) {
+ strlcat(msg, "[Memory BIST test failed, InfiniPath hardware unusable]",
+ msgl);
+ /* ignore from now on, so disable until driver reloaded */
+ dd->ipath_hwerrmask &= ~INFINIPATH_HWE_MEMBISTFAILED;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
+ dd->ipath_hwerrmask);
+ }
+#define _IPATH_PLL_FAIL (INFINIPATH_HWE_COREPLL_FBSLIP | \
+ INFINIPATH_HWE_COREPLL_RFSLIP | \
+ INFINIPATH_HWE_HTBPLL_FBSLIP | \
+ INFINIPATH_HWE_HTBPLL_RFSLIP | \
+ INFINIPATH_HWE_HTAPLL_FBSLIP | \
+ INFINIPATH_HWE_HTAPLL_RFSLIP)
+
+ if (hwerrs & _IPATH_PLL_FAIL) {
+ snprintf(bitsmsg, sizeof bitsmsg,
+ "[PLL failed (%llx), InfiniPath hardware unusable]",
+ (unsigned long long) (hwerrs & _IPATH_PLL_FAIL));
+ strlcat(msg, bitsmsg, msgl);
+ /* ignore from now on, so disable until driver reloaded */
+ dd->ipath_hwerrmask &= ~(hwerrs & _IPATH_PLL_FAIL);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
+ dd->ipath_hwerrmask);
+ }
+
+ if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED) {
+ /*
+ * If it occurs, it is left masked since the eternal
+ * interface is unused
+ */
+ dd->ipath_hwerrmask &= ~INFINIPATH_HWE_SERDESPLLFAILED;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
+ dd->ipath_hwerrmask);
+ }
+
+ if (hwerrs & INFINIPATH_HWE_RXDSYNCMEMPARITYERR)
+ strlcat(msg, "[Rx Dsync]", msgl);
+ if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED)
+ strlcat(msg, "[SerDes PLL]", msgl);
+
+ ipath_dev_err(dd, "%s hardware error\n", msg);
+ if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg)
+ /*
+ * for status file; if no trailing brace is copied,
+ * we'll know it was truncated.
+ */
+ snprintf(dd->ipath_freezemsg,
+ dd->ipath_freezelen, "{%s}", msg);
+
+bail:;
+}
+
+/**
+ * ipath_ht_boardname - fill in the board name
+ * @dd: the infinipath device
+ * @name: the output buffer
+ * @namelen: the size of the output buffer
+ *
+ * fill in the board name, based on the board revision register
+ */
+static int ipath_ht_boardname(struct ipath_devdata *dd, char *name,
+ size_t namelen)
+{
+ char *n = NULL;
+ u8 boardrev = dd->ipath_boardrev;
+ int ret;
+
+ switch (boardrev) {
+ case 4: /* Ponderosa is one of the bringup boards */
+ n = "Ponderosa";
+ break;
+ case 5:
+ /*
+ * original production board; two production levels, with
+ * different serial number ranges. See ipath_ht_early_init() for
+ * case where we enable IPATH_GPIO_INTR for later serial # range.
+ */
+ n = "InfiniPath_QHT7040";
+ break;
+ case 6:
+ n = "OEM_Board_3";
+ break;
+ case 7:
+ /* small form factor production board */
+ n = "InfiniPath_QHT7140";
+ break;
+ case 8:
+ n = "LS/X-1";
+ break;
+ case 9: /* Comstock bringup test board */
+ n = "Comstock";
+ break;
+ case 10:
+ n = "OEM_Board_2";
+ break;
+ case 11:
+ n = "InfiniPath_HT-470"; /* obsoleted */
+ break;
+ case 12:
+ n = "OEM_Board_4";
+ break;
+ default: /* don't know, just print the number */
+ ipath_dev_err(dd, "Don't yet know about board "
+ "with ID %u\n", boardrev);
+ snprintf(name, namelen, "Unknown_InfiniPath_QHT7xxx_%u",
+ boardrev);
+ break;
+ }
+ if (n)
+ snprintf(name, namelen, "%s", n);
+
+ if (dd->ipath_majrev != 3 || (dd->ipath_minrev < 2 || dd->ipath_minrev > 3)) {
+ /*
+ * This version of the driver only supports Rev 3.2 and 3.3
+ */
+ ipath_dev_err(dd,
+ "Unsupported InfiniPath hardware revision %u.%u!\n",
+ dd->ipath_majrev, dd->ipath_minrev);
+ ret = 1;
+ goto bail;
+ }
+ /*
+ * pkt/word counters are 32 bit, and therefore wrap fast enough
+ * that we snapshot them from a timer, and maintain 64 bit shadow
+ * copies
+ */
+ dd->ipath_flags |= IPATH_32BITCOUNTERS;
+ if (dd->ipath_htspeed != 800)
+ ipath_dev_err(dd,
+ "Incorrectly configured for HT @ %uMHz\n",
+ dd->ipath_htspeed);
+ if (dd->ipath_boardrev == 7 || dd->ipath_boardrev == 11 ||
+ dd->ipath_boardrev == 6)
+ dd->ipath_flags |= IPATH_GPIO_INTR;
+ else
+ dd->ipath_flags |= IPATH_POLL_RX_INTR;
+ if (dd->ipath_boardrev == 8) { /* LS/X-1 */
+ u64 val;
+ val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
+ if (val & INFINIPATH_EXTS_SERDESSEL) {
+ /*
+ * hardware disabled
+ *
+ * This means that the chip is hardware disabled,
+ * and will not be able to bring up the link,
+ * in any case. We special case this and abort
+ * early, to avoid later messages. We also set
+ * the DISABLED status bit
+ */
+ ipath_dbg("Unit %u is hardware-disabled\n",
+ dd->ipath_unit);
+ *dd->ipath_statusp |= IPATH_STATUS_DISABLED;
+ /* this value is handled differently */
+ ret = 2;
+ goto bail;
+ }
+ }
+ ret = 0;
+
+bail:
+ return ret;
+}
+
+static void ipath_check_htlink(struct ipath_devdata *dd)
+{
+ u8 linkerr, link_off, i;
+
+ for (i = 0; i < 2; i++) {
+ link_off = dd->ipath_ht_slave_off + i * 4 + 0xd;
+ if (pci_read_config_byte(dd->pcidev, link_off, &linkerr))
+ dev_info(&dd->pcidev->dev, "Couldn't read "
+ "linkerror%d of HT slave/primary block\n",
+ i);
+ else if (linkerr & 0xf0) {
+ ipath_cdbg(VERBOSE, "HT linkerr%d bits 0x%x set, "
+ "clearing\n", linkerr >> 4, i);
+ /*
+ * writing the linkerr bits that are set should
+ * clear them
+ */
+ if (pci_write_config_byte(dd->pcidev, link_off,
+ linkerr))
+ ipath_dbg("Failed write to clear HT "
+ "linkerror%d\n", i);
+ if (pci_read_config_byte(dd->pcidev, link_off,
+ &linkerr))
+ dev_info(&dd->pcidev->dev,
+ "Couldn't reread linkerror%d of "
+ "HT slave/primary block\n", i);
+ else if (linkerr & 0xf0)
+ dev_info(&dd->pcidev->dev,
+ "HT linkerror%d bits 0x%x "
+ "couldn't be cleared\n",
+ i, linkerr >> 4);
+ }
+ }
+}
+
+static int ipath_setup_ht_reset(struct ipath_devdata *dd)
+{
+ ipath_dbg("No reset possible for this InfiniPath hardware\n");
+ return 0;
+}
+
+#define HT_CAPABILITY_ID 0x08 /* HT capabilities not defined in kernel */
+#define HT_INTR_DISC_CONFIG 0x80 /* HT interrupt and discovery cap */
+#define HT_INTR_REG_INDEX 2 /* intconfig requires indirect accesses */
+
+/*
+ * Bits 13-15 of command==0 is slave/primary block. Clear any HT CRC
+ * errors. We only bother to do this at load time, because it's OK if
+ * it happened before we were loaded (first time after boot/reset),
+ * but any time after that, it's fatal anyway. Also need to not check
+ * for for upper byte errors if we are in 8 bit mode, so figure out
+ * our width. For now, at least, also complain if it's 8 bit.
+ */
+static void slave_or_pri_blk(struct ipath_devdata *dd, struct pci_dev *pdev,
+ int pos, u8 cap_type)
+{
+ u8 linkwidth = 0, linkerr, link_a_b_off, link_off;
+ u16 linkctrl = 0;
+ int i;
+
+ dd->ipath_ht_slave_off = pos;
+ /* command word, master_host bit */
+ /* master host || slave */
+ if ((cap_type >> 2) & 1)
+ link_a_b_off = 4;
+ else
+ link_a_b_off = 0;
+ ipath_cdbg(VERBOSE, "HT%u (Link %c) connected to processor\n",
+ link_a_b_off ? 1 : 0,
+ link_a_b_off ? 'B' : 'A');
+
+ link_a_b_off += pos;
+
+ /*
+ * check both link control registers; clear both HT CRC sets if
+ * necessary.
+ */
+ for (i = 0; i < 2; i++) {
+ link_off = pos + i * 4 + 0x4;
+ if (pci_read_config_word(pdev, link_off, &linkctrl))
+ ipath_dev_err(dd, "Couldn't read HT link control%d "
+ "register\n", i);
+ else if (linkctrl & (0xf << 8)) {
+ ipath_cdbg(VERBOSE, "Clear linkctrl%d CRC Error "
+ "bits %x\n", i, linkctrl & (0xf << 8));
+ /*
+ * now write them back to clear the error.
+ */
+ pci_write_config_byte(pdev, link_off,
+ linkctrl & (0xf << 8));
+ }
+ }
+
+ /*
+ * As with HT CRC bits, same for protocol errors that might occur
+ * during boot.
+ */
+ for (i = 0; i < 2; i++) {
+ link_off = pos + i * 4 + 0xd;
+ if (pci_read_config_byte(pdev, link_off, &linkerr))
+ dev_info(&pdev->dev, "Couldn't read linkerror%d "
+ "of HT slave/primary block\n", i);
+ else if (linkerr & 0xf0) {
+ ipath_cdbg(VERBOSE, "HT linkerr%d bits 0x%x set, "
+ "clearing\n", linkerr >> 4, i);
+ /*
+ * writing the linkerr bits that are set will clear
+ * them
+ */
+ if (pci_write_config_byte
+ (pdev, link_off, linkerr))
+ ipath_dbg("Failed write to clear HT "
+ "linkerror%d\n", i);
+ if (pci_read_config_byte(pdev, link_off, &linkerr))
+ dev_info(&pdev->dev, "Couldn't reread "
+ "linkerror%d of HT slave/primary "
+ "block\n", i);
+ else if (linkerr & 0xf0)
+ dev_info(&pdev->dev, "HT linkerror%d bits "
+ "0x%x couldn't be cleared\n",
+ i, linkerr >> 4);
+ }
+ }
+
+ /*
+ * this is just for our link to the host, not devices connected
+ * through tunnel.
+ */
+
+ if (pci_read_config_byte(pdev, link_a_b_off + 7, &linkwidth))
+ ipath_dev_err(dd, "Couldn't read HT link width "
+ "config register\n");
+ else {
+ u32 width;
+ switch (linkwidth & 7) {
+ case 5:
+ width = 4;
+ break;
+ case 4:
+ width = 2;
+ break;
+ case 3:
+ width = 32;
+ break;
+ case 1:
+ width = 16;
+ break;
+ case 0:
+ default: /* if wrong, assume 8 bit */
+ width = 8;
+ break;
+ }
+
+ dd->ipath_htwidth = width;
+
+ if (linkwidth != 0x11) {
+ ipath_dev_err(dd, "Not configured for 16 bit HT "
+ "(%x)\n", linkwidth);
+ if (!(linkwidth & 0xf)) {
+ ipath_dbg("Will ignore HT lane1 errors\n");
+ dd->ipath_flags |= IPATH_8BIT_IN_HT0;
+ }
+ }
+ }
+
+ /*
+ * this is just for our link to the host, not devices connected
+ * through tunnel.
+ */
+ if (pci_read_config_byte(pdev, link_a_b_off + 0xd, &linkwidth))
+ ipath_dev_err(dd, "Couldn't read HT link frequency "
+ "config register\n");
+ else {
+ u32 speed;
+ switch (linkwidth & 0xf) {
+ case 6:
+ speed = 1000;
+ break;
+ case 5:
+ speed = 800;
+ break;
+ case 4:
+ speed = 600;
+ break;
+ case 3:
+ speed = 500;
+ break;
+ case 2:
+ speed = 400;
+ break;
+ case 1:
+ speed = 300;
+ break;
+ default:
+ /*
+ * assume reserved and vendor-specific are 200...
+ */
+ case 0:
+ speed = 200;
+ break;
+ }
+ dd->ipath_htspeed = speed;
+ }
+}
+
+static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev,
+ int pos)
+{
+ u32 int_handler_addr_lower;
+ u32 int_handler_addr_upper;
+ u64 ihandler;
+ u32 intvec;
+
+ /* use indirection register to get the intr handler */
+ pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x10);
+ pci_read_config_dword(pdev, pos + 4, &int_handler_addr_lower);
+ pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x11);
+ pci_read_config_dword(pdev, pos + 4, &int_handler_addr_upper);
+
+ ihandler = (u64) int_handler_addr_lower |
+ ((u64) int_handler_addr_upper << 32);
+
+ /*
+ * kernels with CONFIG_PCI_MSI set the vector in the irq field of
+ * struct pci_device, so we use that to program the internal
+ * interrupt register (not config space) with that value. The BIOS
+ * must still have done the basic MSI setup.
+ */
+ intvec = pdev->irq;
+ /*
+ * clear any vector bits there; normally not set but we'll overload
+ * this for some debug purposes (setting the HTC debug register
+ * value from software, rather than GPIOs), so it might be set on a
+ * driver reload.
+ */
+ ihandler &= ~0xff0000;
+ /* x86 vector goes in intrinfo[23:16] */
+ ihandler |= intvec << 16;
+ ipath_cdbg(VERBOSE, "ihandler lower %x, upper %x, intvec %x, "
+ "interruptconfig %llx\n", int_handler_addr_lower,
+ int_handler_addr_upper, intvec,
+ (unsigned long long) ihandler);
+
+ /* can't program yet, so save for interrupt setup */
+ dd->ipath_intconfig = ihandler;
+ /* keep going, so we find link control stuff also */
+
+ return ihandler != 0;
+}
+
+/**
+ * ipath_setup_ht_config - setup the interruptconfig register
+ * @dd: the infinipath device
+ * @pdev: the PCI device
+ *
+ * setup the interruptconfig register from the HT config info.
+ * Also clear CRC errors in HT linkcontrol, if necessary.
+ * This is done only for the real hardware. It is done before
+ * chip address space is initted, so can't touch infinipath registers
+ */
+static int ipath_setup_ht_config(struct ipath_devdata *dd,
+ struct pci_dev *pdev)
+{
+ int pos, ret = 0;
+ int ihandler = 0;
+
+ /*
+ * Read the capability info to find the interrupt info, and also
+ * handle clearing CRC errors in linkctrl register if necessary. We
+ * do this early, before we ever enable errors or hardware errors,
+ * mostly to avoid causing the chip to enter freeze mode.
+ */
+ pos = pci_find_capability(pdev, HT_CAPABILITY_ID);
+ if (!pos) {
+ ipath_dev_err(dd, "Couldn't find HyperTransport "
+ "capability; no interrupts\n");
+ ret = -ENODEV;
+ goto bail;
+ }
+ do {
+ u8 cap_type;
+
+ /* the HT capability type byte is 3 bytes after the
+ * capability byte.
+ */
+ if (pci_read_config_byte(pdev, pos + 3, &cap_type)) {
+ dev_info(&pdev->dev, "Couldn't read config "
+ "command @ %d\n", pos);
+ continue;
+ }
+ if (!(cap_type & 0xE0))
+ slave_or_pri_blk(dd, pdev, pos, cap_type);
+ else if (cap_type == HT_INTR_DISC_CONFIG)
+ ihandler = set_int_handler(dd, pdev, pos);
+ } while ((pos = pci_find_next_capability(pdev, pos,
+ HT_CAPABILITY_ID)));
+
+ if (!ihandler) {
+ ipath_dev_err(dd, "Couldn't find interrupt handler in "
+ "config space\n");
+ ret = -ENODEV;
+ }
+
+bail:
+ return ret;
+}
+
+/**
+ * ipath_setup_ht_cleanup - clean up any per-chip chip-specific stuff
+ * @dd: the infinipath device
+ *
+ * Called during driver unload.
+ * This is currently a nop for the HT chip, not for all chips
+ */
+static void ipath_setup_ht_cleanup(struct ipath_devdata *dd)
+{
+}
+
+/**
+ * ipath_setup_ht_setextled - set the state of the two external LEDs
+ * @dd: the infinipath device
+ * @lst: the L state
+ * @ltst: the LT state
+ *
+ * Set the state of the two external LEDs, to indicate physical and
+ * logical state of IB link. For this chip (at least with recommended
+ * board pinouts), LED1 is Green (physical state), and LED2 is Yellow
+ * (logical state)
+ *
+ * Note: We try to match the Mellanox HCA LED behavior as best
+ * we can. Green indicates physical link state is OK (something is
+ * plugged in, and we can train).
+ * Amber indicates the link is logically up (ACTIVE).
+ * Mellanox further blinks the amber LED to indicate data packet
+ * activity, but we have no hardware support for that, so it would
+ * require waking up every 10-20 msecs and checking the counters
+ * on the chip, and then turning the LED off if appropriate. That's
+ * visible overhead, so not something we will do.
+ *
+ */
+static void ipath_setup_ht_setextled(struct ipath_devdata *dd,
+ u64 lst, u64 ltst)
+{
+ u64 extctl;
+
+ /* the diags use the LED to indicate diag info, so we leave
+ * the external LED alone when the diags are running */
+ if (ipath_diag_inuse)
+ return;
+
+ /*
+ * start by setting both LED control bits to off, then turn
+ * on the appropriate bit(s).
+ */
+ if (dd->ipath_boardrev == 8) { /* LS/X-1 uses different pins */
+ /*
+ * major difference is that INFINIPATH_EXTC_LEDGBLERR_OFF
+ * is inverted, because it is normally used to indicate
+ * a hardware fault at reset, if there were errors
+ */
+ extctl = (dd->ipath_extctrl & ~INFINIPATH_EXTC_LEDGBLOK_ON)
+ | INFINIPATH_EXTC_LEDGBLERR_OFF;
+ if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP)
+ extctl &= ~INFINIPATH_EXTC_LEDGBLERR_OFF;
+ if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
+ extctl |= INFINIPATH_EXTC_LEDGBLOK_ON;
+ }
+ else {
+ extctl = dd->ipath_extctrl &
+ ~(INFINIPATH_EXTC_LED1PRIPORT_ON |
+ INFINIPATH_EXTC_LED2PRIPORT_ON);
+ if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP)
+ extctl |= INFINIPATH_EXTC_LED1PRIPORT_ON;
+ if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
+ extctl |= INFINIPATH_EXTC_LED2PRIPORT_ON;
+ }
+ dd->ipath_extctrl = extctl;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, extctl);
+}
+
+static void ipath_init_ht_variables(void)
+{
+ ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM;
+ ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM;
+ ipath_gpio_sda = IPATH_GPIO_SDA;
+ ipath_gpio_scl = IPATH_GPIO_SCL;
+
+ infinipath_i_bitsextant =
+ (INFINIPATH_I_RCVURG_MASK << INFINIPATH_I_RCVURG_SHIFT) |
+ (INFINIPATH_I_RCVAVAIL_MASK <<
+ INFINIPATH_I_RCVAVAIL_SHIFT) |
+ INFINIPATH_I_ERROR | INFINIPATH_I_SPIOSENT |
+ INFINIPATH_I_SPIOBUFAVAIL | INFINIPATH_I_GPIO;
+
+ infinipath_e_bitsextant =
+ INFINIPATH_E_RFORMATERR | INFINIPATH_E_RVCRC |
+ INFINIPATH_E_RICRC | INFINIPATH_E_RMINPKTLEN |
+ INFINIPATH_E_RMAXPKTLEN | INFINIPATH_E_RLONGPKTLEN |
+ INFINIPATH_E_RSHORTPKTLEN | INFINIPATH_E_RUNEXPCHAR |
+ INFINIPATH_E_RUNSUPVL | INFINIPATH_E_REBP |
+ INFINIPATH_E_RIBFLOW | INFINIPATH_E_RBADVERSION |
+ INFINIPATH_E_RRCVEGRFULL | INFINIPATH_E_RRCVHDRFULL |
+ INFINIPATH_E_RBADTID | INFINIPATH_E_RHDRLEN |
+ INFINIPATH_E_RHDR | INFINIPATH_E_RIBLOSTLINK |
+ INFINIPATH_E_SMINPKTLEN | INFINIPATH_E_SMAXPKTLEN |
+ INFINIPATH_E_SUNDERRUN | INFINIPATH_E_SPKTLEN |
+ INFINIPATH_E_SDROPPEDSMPPKT | INFINIPATH_E_SDROPPEDDATAPKT |
+ INFINIPATH_E_SPIOARMLAUNCH | INFINIPATH_E_SUNEXPERRPKTNUM |
+ INFINIPATH_E_SUNSUPVL | INFINIPATH_E_IBSTATUSCHANGED |
+ INFINIPATH_E_INVALIDADDR | INFINIPATH_E_RESET |
+ INFINIPATH_E_HARDWARE;
+
+ infinipath_hwe_bitsextant =
+ (INFINIPATH_HWE_HTCMEMPARITYERR_MASK <<
+ INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT) |
+ (INFINIPATH_HWE_TXEMEMPARITYERR_MASK <<
+ INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) |
+ (INFINIPATH_HWE_RXEMEMPARITYERR_MASK <<
+ INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) |
+ INFINIPATH_HWE_HTCLNKABYTE0CRCERR |
+ INFINIPATH_HWE_HTCLNKABYTE1CRCERR |
+ INFINIPATH_HWE_HTCLNKBBYTE0CRCERR |
+ INFINIPATH_HWE_HTCLNKBBYTE1CRCERR |
+ INFINIPATH_HWE_HTCMISCERR4 |
+ INFINIPATH_HWE_HTCMISCERR5 | INFINIPATH_HWE_HTCMISCERR6 |
+ INFINIPATH_HWE_HTCMISCERR7 |
+ INFINIPATH_HWE_HTCBUSTREQPARITYERR |
+ INFINIPATH_HWE_HTCBUSTRESPPARITYERR |
+ INFINIPATH_HWE_HTCBUSIREQPARITYERR |
+ INFINIPATH_HWE_RXDSYNCMEMPARITYERR |
+ INFINIPATH_HWE_MEMBISTFAILED |
+ INFINIPATH_HWE_COREPLL_FBSLIP |
+ INFINIPATH_HWE_COREPLL_RFSLIP |
+ INFINIPATH_HWE_HTBPLL_FBSLIP |
+ INFINIPATH_HWE_HTBPLL_RFSLIP |
+ INFINIPATH_HWE_HTAPLL_FBSLIP |
+ INFINIPATH_HWE_HTAPLL_RFSLIP |
+ INFINIPATH_HWE_SERDESPLLFAILED |
+ INFINIPATH_HWE_IBCBUSTOSPCPARITYERR |
+ INFINIPATH_HWE_IBCBUSFRSPCPARITYERR;
+
+ infinipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK;
+ infinipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK;
+}
+
+/**
+ * ipath_ht_init_hwerrors - enable hardware errors
+ * @dd: the infinipath device
+ *
+ * now that we have finished initializing everything that might reasonably
+ * cause a hardware error, and cleared those errors bits as they occur,
+ * we can enable hardware errors in the mask (potentially enabling
+ * freeze mode), and enable hardware errors as errors (along with
+ * everything else) in errormask
+ */
+static void ipath_ht_init_hwerrors(struct ipath_devdata *dd)
+{
+ ipath_err_t val;
+ u64 extsval;
+
+ extsval = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
+
+ if (!(extsval & INFINIPATH_EXTS_MEMBIST_ENDTEST))
+ ipath_dev_err(dd, "MemBIST did not complete!\n");
+
+ ipath_check_htlink(dd);
+
+ /* barring bugs, all hwerrors become interrupts, which can */
+ val = -1LL;
+ /* don't look at crc lane1 if 8 bit */
+ if (dd->ipath_flags & IPATH_8BIT_IN_HT0)
+ val &= ~infinipath_hwe_htclnkabyte1crcerr;
+ /* don't look at crc lane1 if 8 bit */
+ if (dd->ipath_flags & IPATH_8BIT_IN_HT1)
+ val &= ~infinipath_hwe_htclnkbbyte1crcerr;
+
+ /*
+ * disable RXDSYNCMEMPARITY because external serdes is unused,
+ * and therefore the logic will never be used or initialized,
+ * and uninitialized state will normally result in this error
+ * being asserted. Similarly for the external serdess pll
+ * lock signal.
+ */
+ val &= ~(INFINIPATH_HWE_SERDESPLLFAILED |
+ INFINIPATH_HWE_RXDSYNCMEMPARITYERR);
+
+ /*
+ * Disable MISCERR4 because of an inversion in the HT core
+ * logic checking for errors that cause this bit to be set.
+ * The errata can also cause the protocol error bit to be set
+ * in the HT config space linkerror register(s).
+ */
+ val &= ~INFINIPATH_HWE_HTCMISCERR4;
+
+ /*
+ * PLL ignored because MDIO interface has a logic problem
+ * for reads, on Comstock and Ponderosa. BRINGUP
+ */
+ if (dd->ipath_boardrev == 4 || dd->ipath_boardrev == 9)
+ val &= ~INFINIPATH_HWE_SERDESPLLFAILED;
+ dd->ipath_hwerrmask = val;
+}
+
+/**
+ * ipath_ht_bringup_serdes - bring up the serdes
+ * @dd: the infinipath device
+ */
+static int ipath_ht_bringup_serdes(struct ipath_devdata *dd)
+{
+ u64 val, config1;
+ int ret = 0, change = 0;
+
+ ipath_dbg("Trying to bringup serdes\n");
+
+ if (ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus) &
+ INFINIPATH_HWE_SERDESPLLFAILED)
+ {
+ ipath_dbg("At start, serdes PLL failed bit set in "
+ "hwerrstatus, clearing and continuing\n");
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
+ INFINIPATH_HWE_SERDESPLLFAILED);
+ }
+
+ val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
+ config1 = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig1);
+
+ ipath_cdbg(VERBOSE, "Initial serdes status is config0=%llx "
+ "config1=%llx, sstatus=%llx xgxs %llx\n",
+ (unsigned long long) val, (unsigned long long) config1,
+ (unsigned long long)
+ ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesstatus),
+ (unsigned long long)
+ ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
+
+ /* force reset on */
+ val |= INFINIPATH_SERDC0_RESET_PLL
+ /* | INFINIPATH_SERDC0_RESET_MASK */
+ ;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
+ udelay(15); /* need pll reset set at least for a bit */
+
+ if (val & INFINIPATH_SERDC0_RESET_PLL) {
+ u64 val2 = val &= ~INFINIPATH_SERDC0_RESET_PLL;
+ /* set lane resets, and tx idle, during pll reset */
+ val2 |= INFINIPATH_SERDC0_RESET_MASK |
+ INFINIPATH_SERDC0_TXIDLE;
+ ipath_cdbg(VERBOSE, "Clearing serdes PLL reset (writing "
+ "%llx)\n", (unsigned long long) val2);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0,
+ val2);
+ /*
+ * be sure chip saw it
+ */
+ val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
+ /*
+ * need pll reset clear at least 11 usec before lane
+ * resets cleared; give it a few more
+ */
+ udelay(15);
+ val = val2; /* for check below */
+ }
+
+ if (val & (INFINIPATH_SERDC0_RESET_PLL |
+ INFINIPATH_SERDC0_RESET_MASK |
+ INFINIPATH_SERDC0_TXIDLE)) {
+ val &= ~(INFINIPATH_SERDC0_RESET_PLL |
+ INFINIPATH_SERDC0_RESET_MASK |
+ INFINIPATH_SERDC0_TXIDLE);
+ /* clear them */
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0,
+ val);
+ }
+
+ val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
+ if (((val >> INFINIPATH_XGXS_MDIOADDR_SHIFT) &
+ INFINIPATH_XGXS_MDIOADDR_MASK) != 3) {
+ val &= ~(INFINIPATH_XGXS_MDIOADDR_MASK <<
+ INFINIPATH_XGXS_MDIOADDR_SHIFT);
+ /*
+ * we use address 3
+ */
+ val |= 3ULL << INFINIPATH_XGXS_MDIOADDR_SHIFT;
+ change = 1;
+ }
+ if (val & INFINIPATH_XGXS_RESET) {
+ /* normally true after boot */
+ val &= ~INFINIPATH_XGXS_RESET;
+ change = 1;
+ }
+ if (change)
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
+
+ val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
+
+ /* clear current and de-emphasis bits */
+ config1 &= ~0x0ffffffff00ULL;
+ /* set current to 20ma */
+ config1 |= 0x00000000000ULL;
+ /* set de-emphasis to -5.68dB */
+ config1 |= 0x0cccc000000ULL;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig1, config1);
+
+ ipath_cdbg(VERBOSE, "After setup: serdes status is config0=%llx "
+ "config1=%llx, sstatus=%llx xgxs %llx\n",
+ (unsigned long long) val, (unsigned long long) config1,
+ (unsigned long long)
+ ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesstatus),
+ (unsigned long long)
+ ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
+
+ if (!ipath_waitfor_mdio_cmdready(dd)) {
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_mdio,
+ ipath_mdio_req(IPATH_MDIO_CMD_READ, 31,
+ IPATH_MDIO_CTRL_XGXS_REG_8,
+ 0));
+ if (ipath_waitfor_complete(dd, dd->ipath_kregs->kr_mdio,
+ IPATH_MDIO_DATAVALID, &val))
+ ipath_dbg("Never got MDIO data for XGXS status "
+ "read\n");
+ else
+ ipath_cdbg(VERBOSE, "MDIO Read reg8, "
+ "'bank' 31 %x\n", (u32) val);
+ } else
+ ipath_dbg("Never got MDIO cmdready for XGXS status read\n");
+
+ return ret; /* for now, say we always succeeded */
+}
+
+/**
+ * ipath_ht_quiet_serdes - set serdes to txidle
+ * @dd: the infinipath device
+ * driver is being unloaded
+ */
+static void ipath_ht_quiet_serdes(struct ipath_devdata *dd)
+{
+ u64 val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
+
+ val |= INFINIPATH_SERDC0_TXIDLE;
+ ipath_dbg("Setting TxIdleEn on serdes (config0 = %llx)\n",
+ (unsigned long long) val);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
+}
+
+static int ipath_ht_intconfig(struct ipath_devdata *dd)
+{
+ int ret;
+
+ if (!dd->ipath_intconfig) {
+ ipath_dev_err(dd, "No interrupts enabled, couldn't setup "
+ "interrupt address\n");
+ ret = 1;
+ goto bail;
+ }
+
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig,
+ dd->ipath_intconfig); /* interrupt address */
+ ret = 0;
+
+bail:
+ return ret;
+}
+
+/**
+ * ipath_pe_put_tid - write a TID in chip
+ * @dd: the infinipath device
+ * @tidptr: pointer to the expected TID (in chip) to udpate
+ * @tidtype: 0 for eager, 1 for expected
+ * @pa: physical address of in memory buffer; ipath_tidinvalid if freeing
+ *
+ * This exists as a separate routine to allow for special locking etc.
+ * It's used for both the full cleanup on exit, as well as the normal
+ * setup and teardown.
+ */
+static void ipath_ht_put_tid(struct ipath_devdata *dd,
+ u64 __iomem *tidptr, u32 type,
+ unsigned long pa)
+{
+ if (pa != dd->ipath_tidinvalid) {
+ if (unlikely((pa & ~INFINIPATH_RT_ADDR_MASK))) {
+ dev_info(&dd->pcidev->dev,
+ "physaddr %lx has more than "
+ "40 bits, using only 40!!!\n", pa);
+ pa &= INFINIPATH_RT_ADDR_MASK;
+ }
+ if (type == 0)
+ pa |= dd->ipath_tidtemplate;
+ else {
+ /* in words (fixed, full page). */
+ u64 lenvalid = PAGE_SIZE >> 2;
+ lenvalid <<= INFINIPATH_RT_BUFSIZE_SHIFT;
+ pa |= lenvalid | INFINIPATH_RT_VALID;
+ }
+ }
+ if (dd->ipath_kregbase)
+ writeq(pa, tidptr);
+}
+
+/**
+ * ipath_ht_clear_tid - clear all TID entries for a port, expected and eager
+ * @dd: the infinipath device
+ * @port: the port
+ *
+ * Used from ipath_close(), and at chip initialization.
+ */
+static void ipath_ht_clear_tids(struct ipath_devdata *dd, unsigned port)
+{
+ u64 __iomem *tidbase;
+ int i;
+
+ if (!dd->ipath_kregbase)
+ return;
+
+ ipath_cdbg(VERBOSE, "Invalidate TIDs for port %u\n", port);
+
+ /*
+ * need to invalidate all of the expected TID entries for this
+ * port, so we don't have valid entries that might somehow get
+ * used (early in next use of this port, or through some bug)
+ */
+ tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) +
+ dd->ipath_rcvtidbase +
+ port * dd->ipath_rcvtidcnt *
+ sizeof(*tidbase));
+ for (i = 0; i < dd->ipath_rcvtidcnt; i++)
+ ipath_ht_put_tid(dd, &tidbase[i], 1, dd->ipath_tidinvalid);
+
+ tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) +
+ dd->ipath_rcvegrbase +
+ port * dd->ipath_rcvegrcnt *
+ sizeof(*tidbase));
+
+ for (i = 0; i < dd->ipath_rcvegrcnt; i++)
+ ipath_ht_put_tid(dd, &tidbase[i], 0, dd->ipath_tidinvalid);
+}
+
+/**
+ * ipath_ht_tidtemplate - setup constants for TID updates
+ * @dd: the infinipath device
+ *
+ * We setup stuff that we use a lot, to avoid calculating each time
+ */
+static void ipath_ht_tidtemplate(struct ipath_devdata *dd)
+{
+ dd->ipath_tidtemplate = dd->ipath_ibmaxlen >> 2;
+ dd->ipath_tidtemplate <<= INFINIPATH_RT_BUFSIZE_SHIFT;
+ dd->ipath_tidtemplate |= INFINIPATH_RT_VALID;
+
+ /*
+ * work around chip errata bug 7358, by marking invalid tids
+ * as having max length
+ */
+ dd->ipath_tidinvalid = (-1LL & INFINIPATH_RT_BUFSIZE_MASK) <<
+ INFINIPATH_RT_BUFSIZE_SHIFT;
+}
+
+static int ipath_ht_early_init(struct ipath_devdata *dd)
+{
+ u32 __iomem *piobuf;
+ u32 pioincr, val32, egrsize;
+ int i;
+
+ /*
+ * one cache line; long IB headers will spill over into received
+ * buffer
+ */
+ dd->ipath_rcvhdrentsize = 16;
+ dd->ipath_rcvhdrsize = IPATH_DFLT_RCVHDRSIZE;
+
+ /*
+ * For HT, we allocate a somewhat overly large eager buffer,
+ * such that we can guarantee that we can receive the largest
+ * packet that we can send out. To truly support a 4KB MTU,
+ * we need to bump this to a large value. To date, other than
+ * testing, we have never encountered an HCA that can really
+ * send 4KB MTU packets, so we do not handle that (we'll get
+ * errors interrupts if we ever see one).
+ */
+ dd->ipath_rcvegrbufsize = dd->ipath_piosize2k;
+ egrsize = dd->ipath_rcvegrbufsize;
+
+ /*
+ * the min() check here is currently a nop, but it may not
+ * always be, depending on just how we do ipath_rcvegrbufsize
+ */
+ dd->ipath_ibmaxlen = min(dd->ipath_piosize2k,
+ dd->ipath_rcvegrbufsize);
+ dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen;
+ ipath_ht_tidtemplate(dd);
+
+ /*
+ * zero all the TID entries at startup. We do this for sanity,
+ * in case of a previous driver crash of some kind, and also
+ * because the chip powers up with these memories in an unknown
+ * state. Use portcnt, not cfgports, since this is for the
+ * full chip, not for current (possibly different) configuration
+ * value.
+ * Chip Errata bug 6447
+ */
+ for (val32 = 0; val32 < dd->ipath_portcnt; val32++)
+ ipath_ht_clear_tids(dd, val32);
+
+ /*
+ * write the pbc of each buffer, to be sure it's initialized, then
+ * cancel all the buffers, and also abort any packets that might
+ * have been in flight for some reason (the latter is for driver
+ * unload/reload, but isn't a bad idea at first init). PIO send
+ * isn't enabled at this point, so there is no danger of sending
+ * these out on the wire.
+ * Chip Errata bug 6610
+ */
+ piobuf = (u32 __iomem *) (((char __iomem *)(dd->ipath_kregbase)) +
+ dd->ipath_piobufbase);
+ pioincr = dd->ipath_palign / sizeof(*piobuf);
+ for (i = 0; i < dd->ipath_piobcnt2k; i++) {
+ /*
+ * reasonable word count, just to init pbc
+ */
+ writel(16, piobuf);
+ piobuf += pioincr;
+ }
+ /*
+ * self-clearing
+ */
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
+ INFINIPATH_S_ABORT);
+
+ ipath_get_eeprom_info(dd);
+ if(dd->ipath_boardrev == 5 && dd->ipath_serial[0] == '1' &&
+ dd->ipath_serial[1] == '2' && dd->ipath_serial[2] == '8') {
+ /*
+ * Later production QHT7040 has same changes as QHT7140, so
+ * can use GPIO interrupts. They have serial #'s starting
+ * with 128, rather than 112.
+ */
+ dd->ipath_flags |= IPATH_GPIO_INTR;
+ dd->ipath_flags &= ~IPATH_POLL_RX_INTR;
+ }
+ return 0;
+}
+
+/**
+ * ipath_init_ht_get_base_info - set chip-specific flags for user code
+ * @dd: the infinipath device
+ * @kbase: ipath_base_info pointer
+ *
+ * We set the PCIE flag because the lower bandwidth on PCIe vs
+ * HyperTransport can affect some user packet algorithims.
+ */
+static int ipath_ht_get_base_info(struct ipath_portdata *pd, void *kbase)
+{
+ struct ipath_base_info *kinfo = kbase;
+
+ kinfo->spi_runtime_flags |= IPATH_RUNTIME_HT |
+ IPATH_RUNTIME_RCVHDR_COPY;
+
+ return 0;
+}
+
+/**
+ * ipath_init_iba6110_funcs - set up the chip-specific function pointers
+ * @dd: the infinipath device
+ *
+ * This is global, and is called directly at init to set up the
+ * chip-specific function pointers for later use.
+ */
+void ipath_init_iba6110_funcs(struct ipath_devdata *dd)
+{
+ dd->ipath_f_intrsetup = ipath_ht_intconfig;
+ dd->ipath_f_bus = ipath_setup_ht_config;
+ dd->ipath_f_reset = ipath_setup_ht_reset;
+ dd->ipath_f_get_boardname = ipath_ht_boardname;
+ dd->ipath_f_init_hwerrors = ipath_ht_init_hwerrors;
+ dd->ipath_f_early_init = ipath_ht_early_init;
+ dd->ipath_f_handle_hwerrors = ipath_ht_handle_hwerrors;
+ dd->ipath_f_quiet_serdes = ipath_ht_quiet_serdes;
+ dd->ipath_f_bringup_serdes = ipath_ht_bringup_serdes;
+ dd->ipath_f_clear_tids = ipath_ht_clear_tids;
+ dd->ipath_f_put_tid = ipath_ht_put_tid;
+ dd->ipath_f_cleanup = ipath_setup_ht_cleanup;
+ dd->ipath_f_setextled = ipath_setup_ht_setextled;
+ dd->ipath_f_get_base_info = ipath_ht_get_base_info;
+
+ /*
+ * initialize chip-specific variables
+ */
+ dd->ipath_f_tidtemplate = ipath_ht_tidtemplate;
+
+ /*
+ * setup the register offsets, since they are different for each
+ * chip
+ */
+ dd->ipath_kregs = &ipath_ht_kregs;
+ dd->ipath_cregs = &ipath_ht_cregs;
+
+ /*
+ * do very early init that is needed before ipath_f_bus is
+ * called
+ */
+ ipath_init_ht_variables();
+}
--- /dev/null
+/*
+ * Copyright (c) 2006 QLogic, Inc. All rights reserved.
+ * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the
+ * OpenIB.org BSD license below:
+ *
+ * Redistribution and use in source and binary forms, with or
+ * without modification, are permitted provided that the following
+ * conditions are met:
+ *
+ * - Redistributions of source code must retain the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer.
+ *
+ * - Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials
+ * provided with the distribution.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
+ * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
+ * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+ * SOFTWARE.
+ */
+/*
+ * This file contains all of the code that is specific to the
+ * InfiniPath PCIe chip.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+
+
+#include "ipath_kernel.h"
+#include "ipath_registers.h"
+
+/*
+ * This file contains all the chip-specific register information and
+ * access functions for the QLogic InfiniPath PCI-Express chip.
+ *
+ * This lists the InfiniPath registers, in the actual chip layout.
+ * This structure should never be directly accessed.
+ */
+struct _infinipath_do_not_use_kernel_regs {
+ unsigned long long Revision;
+ unsigned long long Control;
+ unsigned long long PageAlign;
+ unsigned long long PortCnt;
+ unsigned long long DebugPortSelect;
+ unsigned long long Reserved0;
+ unsigned long long SendRegBase;
+ unsigned long long UserRegBase;
+ unsigned long long CounterRegBase;
+ unsigned long long Scratch;
+ unsigned long long Reserved1;
+ unsigned long long Reserved2;
+ unsigned long long IntBlocked;
+ unsigned long long IntMask;
+ unsigned long long IntStatus;
+ unsigned long long IntClear;
+ unsigned long long ErrorMask;
+ unsigned long long ErrorStatus;
+ unsigned long long ErrorClear;
+ unsigned long long HwErrMask;
+ unsigned long long HwErrStatus;
+ unsigned long long HwErrClear;
+ unsigned long long HwDiagCtrl;
+ unsigned long long MDIO;
+ unsigned long long IBCStatus;
+ unsigned long long IBCCtrl;
+ unsigned long long ExtStatus;
+ unsigned long long ExtCtrl;
+ unsigned long long GPIOOut;
+ unsigned long long GPIOMask;
+ unsigned long long GPIOStatus;
+ unsigned long long GPIOClear;
+ unsigned long long RcvCtrl;
+ unsigned long long RcvBTHQP;
+ unsigned long long RcvHdrSize;
+ unsigned long long RcvHdrCnt;
+ unsigned long long RcvHdrEntSize;
+ unsigned long long RcvTIDBase;
+ unsigned long long RcvTIDCnt;
+ unsigned long long RcvEgrBase;
+ unsigned long long RcvEgrCnt;
+ unsigned long long RcvBufBase;
+ unsigned long long RcvBufSize;
+ unsigned long long RxIntMemBase;
+ unsigned long long RxIntMemSize;
+ unsigned long long RcvPartitionKey;
+ unsigned long long Reserved3;
+ unsigned long long RcvPktLEDCnt;
+ unsigned long long Reserved4[8];
+ unsigned long long SendCtrl;
+ unsigned long long SendPIOBufBase;
+ unsigned long long SendPIOSize;
+ unsigned long long SendPIOBufCnt;
+ unsigned long long SendPIOAvailAddr;
+ unsigned long long TxIntMemBase;
+ unsigned long long TxIntMemSize;
+ unsigned long long Reserved5;
+ unsigned long long PCIeRBufTestReg0;
+ unsigned long long PCIeRBufTestReg1;
+ unsigned long long Reserved51[6];
+ unsigned long long SendBufferError;
+ unsigned long long SendBufferErrorCONT1;
+ unsigned long long Reserved6SBE[6];
+ unsigned long long RcvHdrAddr0;
+ unsigned long long RcvHdrAddr1;
+ unsigned long long RcvHdrAddr2;
+ unsigned long long RcvHdrAddr3;
+ unsigned long long RcvHdrAddr4;
+ unsigned long long Reserved7RHA[11];
+ unsigned long long RcvHdrTailAddr0;
+ unsigned long long RcvHdrTailAddr1;
+ unsigned long long RcvHdrTailAddr2;
+ unsigned long long RcvHdrTailAddr3;
+ unsigned long long RcvHdrTailAddr4;
+ unsigned long long Reserved8RHTA[11];
+ unsigned long long Reserved9SW[8];
+ unsigned long long SerdesConfig0;
+ unsigned long long SerdesConfig1;
+ unsigned long long SerdesStatus;
+ unsigned long long XGXSConfig;
+ unsigned long long IBPLLCfg;
+ unsigned long long Reserved10SW2[3];
+ unsigned long long PCIEQ0SerdesConfig0;
+ unsigned long long PCIEQ0SerdesConfig1;
+ unsigned long long PCIEQ0SerdesStatus;
+ unsigned long long Reserved11;
+ unsigned long long PCIEQ1SerdesConfig0;
+ unsigned long long PCIEQ1SerdesConfig1;
+ unsigned long long PCIEQ1SerdesStatus;
+ unsigned long long Reserved12;
+};
+
+#define IPATH_KREG_OFFSET(field) (offsetof(struct \
+ _infinipath_do_not_use_kernel_regs, field) / sizeof(u64))
+#define IPATH_CREG_OFFSET(field) (offsetof( \
+ struct infinipath_counters, field) / sizeof(u64))
+
+static const struct ipath_kregs ipath_pe_kregs = {
+ .kr_control = IPATH_KREG_OFFSET(Control),
+ .kr_counterregbase = IPATH_KREG_OFFSET(CounterRegBase),
+ .kr_debugportselect = IPATH_KREG_OFFSET(DebugPortSelect),
+ .kr_errorclear = IPATH_KREG_OFFSET(ErrorClear),
+ .kr_errormask = IPATH_KREG_OFFSET(ErrorMask),
+ .kr_errorstatus = IPATH_KREG_OFFSET(ErrorStatus),
+ .kr_extctrl = IPATH_KREG_OFFSET(ExtCtrl),
+ .kr_extstatus = IPATH_KREG_OFFSET(ExtStatus),
+ .kr_gpio_clear = IPATH_KREG_OFFSET(GPIOClear),
+ .kr_gpio_mask = IPATH_KREG_OFFSET(GPIOMask),
+ .kr_gpio_out = IPATH_KREG_OFFSET(GPIOOut),
+ .kr_gpio_status = IPATH_KREG_OFFSET(GPIOStatus),
+ .kr_hwdiagctrl = IPATH_KREG_OFFSET(HwDiagCtrl),
+ .kr_hwerrclear = IPATH_KREG_OFFSET(HwErrClear),
+ .kr_hwerrmask = IPATH_KREG_OFFSET(HwErrMask),
+ .kr_hwerrstatus = IPATH_KREG_OFFSET(HwErrStatus),
+ .kr_ibcctrl = IPATH_KREG_OFFSET(IBCCtrl),
+ .kr_ibcstatus = IPATH_KREG_OFFSET(IBCStatus),
+ .kr_intblocked = IPATH_KREG_OFFSET(IntBlocked),
+ .kr_intclear = IPATH_KREG_OFFSET(IntClear),
+ .kr_intmask = IPATH_KREG_OFFSET(IntMask),
+ .kr_intstatus = IPATH_KREG_OFFSET(IntStatus),
+ .kr_mdio = IPATH_KREG_OFFSET(MDIO),
+ .kr_pagealign = IPATH_KREG_OFFSET(PageAlign),
+ .kr_partitionkey = IPATH_KREG_OFFSET(RcvPartitionKey),
+ .kr_portcnt = IPATH_KREG_OFFSET(PortCnt),
+ .kr_rcvbthqp = IPATH_KREG_OFFSET(RcvBTHQP),
+ .kr_rcvbufbase = IPATH_KREG_OFFSET(RcvBufBase),
+ .kr_rcvbufsize = IPATH_KREG_OFFSET(RcvBufSize),
+ .kr_rcvctrl = IPATH_KREG_OFFSET(RcvCtrl),
+ .kr_rcvegrbase = IPATH_KREG_OFFSET(RcvEgrBase),
+ .kr_rcvegrcnt = IPATH_KREG_OFFSET(RcvEgrCnt),
+ .kr_rcvhdrcnt = IPATH_KREG_OFFSET(RcvHdrCnt),
+ .kr_rcvhdrentsize = IPATH_KREG_OFFSET(RcvHdrEntSize),
+ .kr_rcvhdrsize = IPATH_KREG_OFFSET(RcvHdrSize),
+ .kr_rcvintmembase = IPATH_KREG_OFFSET(RxIntMemBase),
+ .kr_rcvintmemsize = IPATH_KREG_OFFSET(RxIntMemSize),
+ .kr_rcvtidbase = IPATH_KREG_OFFSET(RcvTIDBase),
+ .kr_rcvtidcnt = IPATH_KREG_OFFSET(RcvTIDCnt),
+ .kr_revision = IPATH_KREG_OFFSET(Revision),
+ .kr_scratch = IPATH_KREG_OFFSET(Scratch),
+ .kr_sendbuffererror = IPATH_KREG_OFFSET(SendBufferError),
+ .kr_sendctrl = IPATH_KREG_OFFSET(SendCtrl),
+ .kr_sendpioavailaddr = IPATH_KREG_OFFSET(SendPIOAvailAddr),
+ .kr_sendpiobufbase = IPATH_KREG_OFFSET(SendPIOBufBase),
+ .kr_sendpiobufcnt = IPATH_KREG_OFFSET(SendPIOBufCnt),
+ .kr_sendpiosize = IPATH_KREG_OFFSET(SendPIOSize),
+ .kr_sendregbase = IPATH_KREG_OFFSET(SendRegBase),
+ .kr_txintmembase = IPATH_KREG_OFFSET(TxIntMemBase),
+ .kr_txintmemsize = IPATH_KREG_OFFSET(TxIntMemSize),
+ .kr_userregbase = IPATH_KREG_OFFSET(UserRegBase),
+ .kr_serdesconfig0 = IPATH_KREG_OFFSET(SerdesConfig0),
+ .kr_serdesconfig1 = IPATH_KREG_OFFSET(SerdesConfig1),
+ .kr_serdesstatus = IPATH_KREG_OFFSET(SerdesStatus),
+ .kr_xgxsconfig = IPATH_KREG_OFFSET(XGXSConfig),
+ .kr_ibpllcfg = IPATH_KREG_OFFSET(IBPLLCfg),
+
+ /*
+ * These should not be used directly via ipath_read_kreg64(),
+ * use them with ipath_read_kreg64_port()
+ */
+ .kr_rcvhdraddr = IPATH_KREG_OFFSET(RcvHdrAddr0),
+ .kr_rcvhdrtailaddr = IPATH_KREG_OFFSET(RcvHdrTailAddr0),
+
+ /* The rcvpktled register controls one of the debug port signals, so
+ * a packet activity LED can be connected to it. */
+ .kr_rcvpktledcnt = IPATH_KREG_OFFSET(RcvPktLEDCnt),
+ .kr_pcierbuftestreg0 = IPATH_KREG_OFFSET(PCIeRBufTestReg0),
+ .kr_pcierbuftestreg1 = IPATH_KREG_OFFSET(PCIeRBufTestReg1),
+ .kr_pcieq0serdesconfig0 = IPATH_KREG_OFFSET(PCIEQ0SerdesConfig0),
+ .kr_pcieq0serdesconfig1 = IPATH_KREG_OFFSET(PCIEQ0SerdesConfig1),
+ .kr_pcieq0serdesstatus = IPATH_KREG_OFFSET(PCIEQ0SerdesStatus),
+ .kr_pcieq1serdesconfig0 = IPATH_KREG_OFFSET(PCIEQ1SerdesConfig0),
+ .kr_pcieq1serdesconfig1 = IPATH_KREG_OFFSET(PCIEQ1SerdesConfig1),
+ .kr_pcieq1serdesstatus = IPATH_KREG_OFFSET(PCIEQ1SerdesStatus)
+};
+
+static const struct ipath_cregs ipath_pe_cregs = {
+ .cr_badformatcnt = IPATH_CREG_OFFSET(RxBadFormatCnt),
+ .cr_erricrccnt = IPATH_CREG_OFFSET(RxICRCErrCnt),
+ .cr_errlinkcnt = IPATH_CREG_OFFSET(RxLinkProblemCnt),
+ .cr_errlpcrccnt = IPATH_CREG_OFFSET(RxLPCRCErrCnt),
+ .cr_errpkey = IPATH_CREG_OFFSET(RxPKeyMismatchCnt),
+ .cr_errrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowCtrlErrCnt),
+ .cr_err_rlencnt = IPATH_CREG_OFFSET(RxLenErrCnt),
+ .cr_errslencnt = IPATH_CREG_OFFSET(TxLenErrCnt),
+ .cr_errtidfull = IPATH_CREG_OFFSET(RxTIDFullErrCnt),
+ .cr_errtidvalid = IPATH_CREG_OFFSET(RxTIDValidErrCnt),
+ .cr_errvcrccnt = IPATH_CREG_OFFSET(RxVCRCErrCnt),
+ .cr_ibstatuschange = IPATH_CREG_OFFSET(IBStatusChangeCnt),
+ .cr_intcnt = IPATH_CREG_OFFSET(LBIntCnt),
+ .cr_invalidrlencnt = IPATH_CREG_OFFSET(RxMaxMinLenErrCnt),
+ .cr_invalidslencnt = IPATH_CREG_OFFSET(TxMaxMinLenErrCnt),
+ .cr_lbflowstallcnt = IPATH_CREG_OFFSET(LBFlowStallCnt),
+ .cr_pktrcvcnt = IPATH_CREG_OFFSET(RxDataPktCnt),
+ .cr_pktrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowPktCnt),
+ .cr_pktsendcnt = IPATH_CREG_OFFSET(TxDataPktCnt),
+ .cr_pktsendflowcnt = IPATH_CREG_OFFSET(TxFlowPktCnt),
+ .cr_portovflcnt = IPATH_CREG_OFFSET(RxP0HdrEgrOvflCnt),
+ .cr_rcvebpcnt = IPATH_CREG_OFFSET(RxEBPCnt),
+ .cr_rcvovflcnt = IPATH_CREG_OFFSET(RxBufOvflCnt),
+ .cr_senddropped = IPATH_CREG_OFFSET(TxDroppedPktCnt),
+ .cr_sendstallcnt = IPATH_CREG_OFFSET(TxFlowStallCnt),
+ .cr_sendunderruncnt = IPATH_CREG_OFFSET(TxUnderrunCnt),
+ .cr_wordrcvcnt = IPATH_CREG_OFFSET(RxDwordCnt),
+ .cr_wordsendcnt = IPATH_CREG_OFFSET(TxDwordCnt),
+ .cr_unsupvlcnt = IPATH_CREG_OFFSET(TxUnsupVLErrCnt),
+ .cr_rxdroppktcnt = IPATH_CREG_OFFSET(RxDroppedPktCnt),
+ .cr_iblinkerrrecovcnt = IPATH_CREG_OFFSET(IBLinkErrRecoveryCnt),
+ .cr_iblinkdowncnt = IPATH_CREG_OFFSET(IBLinkDownedCnt),
+ .cr_ibsymbolerrcnt = IPATH_CREG_OFFSET(IBSymbolErrCnt)
+};
+
+/* kr_intstatus, kr_intclear, kr_intmask bits */
+#define INFINIPATH_I_RCVURG_MASK 0x1F
+#define INFINIPATH_I_RCVAVAIL_MASK 0x1F
+
+/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */
+#define INFINIPATH_HWE_PCIEMEMPARITYERR_MASK 0x000000000000003fULL
+#define INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT 0
+#define INFINIPATH_HWE_PCIEPOISONEDTLP 0x0000000010000000ULL
+#define INFINIPATH_HWE_PCIECPLTIMEOUT 0x0000000020000000ULL
+#define INFINIPATH_HWE_PCIEBUSPARITYXTLH 0x0000000040000000ULL
+#define INFINIPATH_HWE_PCIEBUSPARITYXADM 0x0000000080000000ULL
+#define INFINIPATH_HWE_PCIEBUSPARITYRADM 0x0000000100000000ULL
+#define INFINIPATH_HWE_COREPLL_FBSLIP 0x0080000000000000ULL
+#define INFINIPATH_HWE_COREPLL_RFSLIP 0x0100000000000000ULL
+#define INFINIPATH_HWE_PCIE1PLLFAILED 0x0400000000000000ULL
+#define INFINIPATH_HWE_PCIE0PLLFAILED 0x0800000000000000ULL
+#define INFINIPATH_HWE_SERDESPLLFAILED 0x1000000000000000ULL
+
+/* kr_extstatus bits */
+#define INFINIPATH_EXTS_FREQSEL 0x2
+#define INFINIPATH_EXTS_SERDESSEL 0x4
+#define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000
+#define INFINIPATH_EXTS_MEMBIST_FOUND 0x0000000000008000
+
+#define _IPATH_GPIO_SDA_NUM 1
+#define _IPATH_GPIO_SCL_NUM 0
+
+#define IPATH_GPIO_SDA (1ULL << \
+ (_IPATH_GPIO_SDA_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
+#define IPATH_GPIO_SCL (1ULL << \
+ (_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
+
+/**
+ * ipath_pe_handle_hwerrors - display hardware errors.
+ * @dd: the infinipath device
+ * @msg: the output buffer
+ * @msgl: the size of the output buffer
+ *
+ * Use same msg buffer as regular errors to avoid excessive stack
+ * use. Most hardware errors are catastrophic, but for right now,
+ * we'll print them and continue. We reuse the same message buffer as
+ * ipath_handle_errors() to avoid excessive stack usage.
+ */
+static void ipath_pe_handle_hwerrors(struct ipath_devdata *dd, char *msg,
+ size_t msgl)
+{
+ ipath_err_t hwerrs;
+ u32 bits, ctrl;
+ int isfatal = 0;
+ char bitsmsg[64];
+
+ hwerrs = ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus);
+ if (!hwerrs) {
+ /*
+ * better than printing cofusing messages
+ * This seems to be related to clearing the crc error, or
+ * the pll error during init.
+ */
+ ipath_cdbg(VERBOSE, "Called but no hardware errors set\n");
+ return;
+ } else if (hwerrs == ~0ULL) {
+ ipath_dev_err(dd, "Read of hardware error status failed "
+ "(all bits set); ignoring\n");
+ return;
+ }
+ ipath_stats.sps_hwerrs++;
+
+ /* Always clear the error status register, except MEMBISTFAIL,
+ * regardless of whether we continue or stop using the chip.
+ * We want that set so we know it failed, even across driver reload.
+ * We'll still ignore it in the hwerrmask. We do this partly for
+ * diagnostics, but also for support */
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
+ hwerrs&~INFINIPATH_HWE_MEMBISTFAILED);
+
+ hwerrs &= dd->ipath_hwerrmask;
+
+ /*
+ * make sure we get this much out, unless told to be quiet,
+ * or it's occurred within the last 5 seconds
+ */
+ if ((hwerrs & ~dd->ipath_lasthwerror) ||
+ (ipath_debug & __IPATH_VERBDBG))
+ dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx "
+ "(cleared)\n", (unsigned long long) hwerrs);
+ dd->ipath_lasthwerror |= hwerrs;
+
+ if (hwerrs & ~infinipath_hwe_bitsextant)
+ ipath_dev_err(dd, "hwerror interrupt with unknown errors "
+ "%llx set\n", (unsigned long long)
+ (hwerrs & ~infinipath_hwe_bitsextant));
+
+ ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control);
+ if (ctrl & INFINIPATH_C_FREEZEMODE) {
+ if (hwerrs) {
+ /*
+ * if any set that we aren't ignoring only make the
+ * complaint once, in case it's stuck or recurring,
+ * and we get here multiple times
+ */
+ if (dd->ipath_flags & IPATH_INITTED) {
+ ipath_dev_err(dd, "Fatal Error (freeze "
+ "mode), no longer usable\n");
+ isfatal = 1;
+ }
+ /*
+ * Mark as having had an error for driver, and also
+ * for /sys and status word mapped to user programs.
+ * This marks unit as not usable, until reset
+ */
+ *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY;
+ *dd->ipath_statusp |= IPATH_STATUS_HWERROR;
+ dd->ipath_flags &= ~IPATH_INITTED;
+ } else {
+ ipath_dbg("Clearing freezemode on ignored hardware "
+ "error\n");
+ ctrl &= ~INFINIPATH_C_FREEZEMODE;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
+ ctrl);
+ }
+ }
+
+ *msg = '\0';
+
+ if (hwerrs & INFINIPATH_HWE_MEMBISTFAILED) {
+ strlcat(msg, "[Memory BIST test failed, InfiniPath hardware unusable]",
+ msgl);
+ /* ignore from now on, so disable until driver reloaded */
+ *dd->ipath_statusp |= IPATH_STATUS_HWERROR;
+ dd->ipath_hwerrmask &= ~INFINIPATH_HWE_MEMBISTFAILED;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
+ dd->ipath_hwerrmask);
+ }
+ if (hwerrs & (INFINIPATH_HWE_RXEMEMPARITYERR_MASK
+ << INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT)) {
+ bits = (u32) ((hwerrs >>
+ INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) &
+ INFINIPATH_HWE_RXEMEMPARITYERR_MASK);
+ snprintf(bitsmsg, sizeof bitsmsg, "[RXE Parity Errs %x] ",
+ bits);
+ strlcat(msg, bitsmsg, msgl);
+ }
+ if (hwerrs & (INFINIPATH_HWE_TXEMEMPARITYERR_MASK
+ << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)) {
+ bits = (u32) ((hwerrs >>
+ INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) &
+ INFINIPATH_HWE_TXEMEMPARITYERR_MASK);
+ snprintf(bitsmsg, sizeof bitsmsg, "[TXE Parity Errs %x] ",
+ bits);
+ strlcat(msg, bitsmsg, msgl);
+ }
+ if (hwerrs & (INFINIPATH_HWE_PCIEMEMPARITYERR_MASK
+ << INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT)) {
+ bits = (u32) ((hwerrs >>
+ INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT) &
+ INFINIPATH_HWE_PCIEMEMPARITYERR_MASK);
+ snprintf(bitsmsg, sizeof bitsmsg,
+ "[PCIe Mem Parity Errs %x] ", bits);
+ strlcat(msg, bitsmsg, msgl);
+ }
+ if (hwerrs & INFINIPATH_HWE_IBCBUSTOSPCPARITYERR)
+ strlcat(msg, "[IB2IPATH Parity]", msgl);
+ if (hwerrs & INFINIPATH_HWE_IBCBUSFRSPCPARITYERR)
+ strlcat(msg, "[IPATH2IB Parity]", msgl);
+
+#define _IPATH_PLL_FAIL (INFINIPATH_HWE_COREPLL_FBSLIP | \
+ INFINIPATH_HWE_COREPLL_RFSLIP )
+
+ if (hwerrs & _IPATH_PLL_FAIL) {
+ snprintf(bitsmsg, sizeof bitsmsg,
+ "[PLL failed (%llx), InfiniPath hardware unusable]",
+ (unsigned long long) hwerrs & _IPATH_PLL_FAIL);
+ strlcat(msg, bitsmsg, msgl);
+ /* ignore from now on, so disable until driver reloaded */
+ dd->ipath_hwerrmask &= ~(hwerrs & _IPATH_PLL_FAIL);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
+ dd->ipath_hwerrmask);
+ }
+
+ if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED) {
+ /*
+ * If it occurs, it is left masked since the eternal
+ * interface is unused
+ */
+ dd->ipath_hwerrmask &= ~INFINIPATH_HWE_SERDESPLLFAILED;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
+ dd->ipath_hwerrmask);
+ }
+
+ if (hwerrs & INFINIPATH_HWE_PCIEPOISONEDTLP)
+ strlcat(msg, "[PCIe Poisoned TLP]", msgl);
+ if (hwerrs & INFINIPATH_HWE_PCIECPLTIMEOUT)
+ strlcat(msg, "[PCIe completion timeout]", msgl);
+
+ /*
+ * In practice, it's unlikely wthat we'll see PCIe PLL, or bus
+ * parity or memory parity error failures, because most likely we
+ * won't be able to talk to the core of the chip. Nonetheless, we
+ * might see them, if they are in parts of the PCIe core that aren't
+ * essential.
+ */
+ if (hwerrs & INFINIPATH_HWE_PCIE1PLLFAILED)
+ strlcat(msg, "[PCIePLL1]", msgl);
+ if (hwerrs & INFINIPATH_HWE_PCIE0PLLFAILED)
+ strlcat(msg, "[PCIePLL0]", msgl);
+ if (hwerrs & INFINIPATH_HWE_PCIEBUSPARITYXTLH)
+ strlcat(msg, "[PCIe XTLH core parity]", msgl);
+ if (hwerrs & INFINIPATH_HWE_PCIEBUSPARITYXADM)
+ strlcat(msg, "[PCIe ADM TX core parity]", msgl);
+ if (hwerrs & INFINIPATH_HWE_PCIEBUSPARITYRADM)
+ strlcat(msg, "[PCIe ADM RX core parity]", msgl);
+
+ if (hwerrs & INFINIPATH_HWE_RXDSYNCMEMPARITYERR)
+ strlcat(msg, "[Rx Dsync]", msgl);
+ if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED)
+ strlcat(msg, "[SerDes PLL]", msgl);
+
+ ipath_dev_err(dd, "%s hardware error\n", msg);
+ if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg) {
+ /*
+ * for /sys status file ; if no trailing } is copied, we'll
+ * know it was truncated.
+ */
+ snprintf(dd->ipath_freezemsg, dd->ipath_freezelen,
+ "{%s}", msg);
+ }
+}
+
+/**
+ * ipath_pe_boardname - fill in the board name
+ * @dd: the infinipath device
+ * @name: the output buffer
+ * @namelen: the size of the output buffer
+ *
+ * info is based on the board revision register
+ */
+static int ipath_pe_boardname(struct ipath_devdata *dd, char *name,
+ size_t namelen)
+{
+ char *n = NULL;
+ u8 boardrev = dd->ipath_boardrev;
+ int ret;
+
+ switch (boardrev) {
+ case 0:
+ n = "InfiniPath_Emulation";
+ break;
+ case 1:
+ n = "InfiniPath_QLE7140-Bringup";
+ break;
+ case 2:
+ n = "InfiniPath_QLE7140";
+ break;
+ case 3:
+ n = "InfiniPath_QMI7140";
+ break;
+ case 4:
+ n = "InfiniPath_QEM7140";
+ break;
+ case 5:
+ n = "InfiniPath_QMH7140";
+ break;
+ default:
+ ipath_dev_err(dd,
+ "Don't yet know about board with ID %u\n",
+ boardrev);
+ snprintf(name, namelen, "Unknown_InfiniPath_PCIe_%u",
+ boardrev);
+ break;
+ }
+ if (n)
+ snprintf(name, namelen, "%s", n);
+
+ if (dd->ipath_majrev != 4 || !dd->ipath_minrev || dd->ipath_minrev>2) {
+ ipath_dev_err(dd, "Unsupported InfiniPath hardware revision %u.%u!\n",
+ dd->ipath_majrev, dd->ipath_minrev);
+ ret = 1;
+ } else
+ ret = 0;
+
+ return ret;
+}
+
+/**
+ * ipath_pe_init_hwerrors - enable hardware errors
+ * @dd: the infinipath device
+ *
+ * now that we have finished initializing everything that might reasonably
+ * cause a hardware error, and cleared those errors bits as they occur,
+ * we can enable hardware errors in the mask (potentially enabling
+ * freeze mode), and enable hardware errors as errors (along with
+ * everything else) in errormask
+ */
+static void ipath_pe_init_hwerrors(struct ipath_devdata *dd)
+{
+ ipath_err_t val;
+ u64 extsval;
+
+ extsval = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
+
+ if (!(extsval & INFINIPATH_EXTS_MEMBIST_ENDTEST))
+ ipath_dev_err(dd, "MemBIST did not complete!\n");
+
+ val = ~0ULL; /* barring bugs, all hwerrors become interrupts, */
+
+ if (!dd->ipath_boardrev) // no PLL for Emulator
+ val &= ~INFINIPATH_HWE_SERDESPLLFAILED;
+
+ /* workaround bug 9460 in internal interface bus parity checking */
+ val &= ~INFINIPATH_HWE_PCIEBUSPARITYRADM;
+
+ dd->ipath_hwerrmask = val;
+}
+
+/**
+ * ipath_pe_bringup_serdes - bring up the serdes
+ * @dd: the infinipath device
+ */
+static int ipath_pe_bringup_serdes(struct ipath_devdata *dd)
+{
+ u64 val, tmp, config1;
+ int ret = 0, change = 0;
+
+ ipath_dbg("Trying to bringup serdes\n");
+
+ if (ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus) &
+ INFINIPATH_HWE_SERDESPLLFAILED) {
+ ipath_dbg("At start, serdes PLL failed bit set "
+ "in hwerrstatus, clearing and continuing\n");
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
+ INFINIPATH_HWE_SERDESPLLFAILED);
+ }
+
+ val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
+ config1 = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig1);
+
+ ipath_cdbg(VERBOSE, "SerDes status config0=%llx config1=%llx, "
+ "xgxsconfig %llx\n", (unsigned long long) val,
+ (unsigned long long) config1, (unsigned long long)
+ ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
+
+ /*
+ * Force reset on, also set rxdetect enable. Must do before reading
+ * serdesstatus at least for simulation, or some of the bits in
+ * serdes status will come back as undefined and cause simulation
+ * failures
+ */
+ val |= INFINIPATH_SERDC0_RESET_PLL | INFINIPATH_SERDC0_RXDETECT_EN
+ | INFINIPATH_SERDC0_L1PWR_DN;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
+ /* be sure chip saw it */
+ tmp = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
+ udelay(5); /* need pll reset set at least for a bit */
+ /*
+ * after PLL is reset, set the per-lane Resets and TxIdle and
+ * clear the PLL reset and rxdetect (to get falling edge).
+ * Leave L1PWR bits set (permanently)
+ */
+ val &= ~(INFINIPATH_SERDC0_RXDETECT_EN | INFINIPATH_SERDC0_RESET_PLL
+ | INFINIPATH_SERDC0_L1PWR_DN);
+ val |= INFINIPATH_SERDC0_RESET_MASK | INFINIPATH_SERDC0_TXIDLE;
+ ipath_cdbg(VERBOSE, "Clearing pll reset and setting lane resets "
+ "and txidle (%llx)\n", (unsigned long long) val);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
+ /* be sure chip saw it */
+ tmp = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
+ /* need PLL reset clear for at least 11 usec before lane
+ * resets cleared; give it a few more to be sure */
+ udelay(15);
+ val &= ~(INFINIPATH_SERDC0_RESET_MASK | INFINIPATH_SERDC0_TXIDLE);
+
+ ipath_cdbg(VERBOSE, "Clearing lane resets and txidle "
+ "(writing %llx)\n", (unsigned long long) val);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
+ /* be sure chip saw it */
+ val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
+
+ val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
+ if (((val >> INFINIPATH_XGXS_MDIOADDR_SHIFT) &
+ INFINIPATH_XGXS_MDIOADDR_MASK) != 3) {
+ val &=
+ ~(INFINIPATH_XGXS_MDIOADDR_MASK <<
+ INFINIPATH_XGXS_MDIOADDR_SHIFT);
+ /* MDIO address 3 */
+ val |= 3ULL << INFINIPATH_XGXS_MDIOADDR_SHIFT;
+ change = 1;
+ }
+ if (val & INFINIPATH_XGXS_RESET) {
+ val &= ~INFINIPATH_XGXS_RESET;
+ change = 1;
+ }
+ if (change)
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
+
+ val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
+
+ /* clear current and de-emphasis bits */
+ config1 &= ~0x0ffffffff00ULL;
+ /* set current to 20ma */
+ config1 |= 0x00000000000ULL;
+ /* set de-emphasis to -5.68dB */
+ config1 |= 0x0cccc000000ULL;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig1, config1);
+
+ ipath_cdbg(VERBOSE, "done: SerDes status config0=%llx "
+ "config1=%llx, sstatus=%llx xgxs=%llx\n",
+ (unsigned long long) val, (unsigned long long) config1,
+ (unsigned long long)
+ ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesstatus),
+ (unsigned long long)
+ ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
+
+ if (!ipath_waitfor_mdio_cmdready(dd)) {
+ ipath_write_kreg(
+ dd, dd->ipath_kregs->kr_mdio,
+ ipath_mdio_req(IPATH_MDIO_CMD_READ, 31,
+ IPATH_MDIO_CTRL_XGXS_REG_8, 0));
+ if (ipath_waitfor_complete(dd, dd->ipath_kregs->kr_mdio,
+ IPATH_MDIO_DATAVALID, &val))
+ ipath_dbg("Never got MDIO data for XGXS "
+ "status read\n");
+ else
+ ipath_cdbg(VERBOSE, "MDIO Read reg8, "
+ "'bank' 31 %x\n", (u32) val);
+ } else
+ ipath_dbg("Never got MDIO cmdready for XGXS status read\n");
+
+ return ret;
+}
+
+/**
+ * ipath_pe_quiet_serdes - set serdes to txidle
+ * @dd: the infinipath device
+ * Called when driver is being unloaded
+ */
+static void ipath_pe_quiet_serdes(struct ipath_devdata *dd)
+{
+ u64 val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
+
+ val |= INFINIPATH_SERDC0_TXIDLE;
+ ipath_dbg("Setting TxIdleEn on serdes (config0 = %llx)\n",
+ (unsigned long long) val);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
+}
+
+/* this is not yet needed on this chip, so just return 0. */
+static int ipath_pe_intconfig(struct ipath_devdata *dd)
+{
+ return 0;
+}
+
+/**
+ * ipath_setup_pe_setextled - set the state of the two external LEDs
+ * @dd: the infinipath device
+ * @lst: the L state
+ * @ltst: the LT state
+
+ * These LEDs indicate the physical and logical state of IB link.
+ * For this chip (at least with recommended board pinouts), LED1
+ * is Yellow (logical state) and LED2 is Green (physical state),
+ *
+ * Note: We try to match the Mellanox HCA LED behavior as best
+ * we can. Green indicates physical link state is OK (something is
+ * plugged in, and we can train).
+ * Amber indicates the link is logically up (ACTIVE).
+ * Mellanox further blinks the amber LED to indicate data packet
+ * activity, but we have no hardware support for that, so it would
+ * require waking up every 10-20 msecs and checking the counters
+ * on the chip, and then turning the LED off if appropriate. That's
+ * visible overhead, so not something we will do.
+ *
+ */
+static void ipath_setup_pe_setextled(struct ipath_devdata *dd, u64 lst,
+ u64 ltst)
+{
+ u64 extctl;
+
+ /* the diags use the LED to indicate diag info, so we leave
+ * the external LED alone when the diags are running */
+ if (ipath_diag_inuse)
+ return;
+
+ extctl = dd->ipath_extctrl & ~(INFINIPATH_EXTC_LED1PRIPORT_ON |
+ INFINIPATH_EXTC_LED2PRIPORT_ON);
+
+ if (ltst & INFINIPATH_IBCS_LT_STATE_LINKUP)
+ extctl |= INFINIPATH_EXTC_LED2PRIPORT_ON;
+ if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
+ extctl |= INFINIPATH_EXTC_LED1PRIPORT_ON;
+ dd->ipath_extctrl = extctl;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, extctl);
+}
+
+/**
+ * ipath_setup_pe_cleanup - clean up any per-chip chip-specific stuff
+ * @dd: the infinipath device
+ *
+ * This is called during driver unload.
+ * We do the pci_disable_msi here, not in generic code, because it
+ * isn't used for the HT chips. If we do end up needing pci_enable_msi
+ * at some point in the future for HT, we'll move the call back
+ * into the main init_one code.
+ */
+static void ipath_setup_pe_cleanup(struct ipath_devdata *dd)
+{
+ dd->ipath_msi_lo = 0; /* just in case unload fails */
+ pci_disable_msi(dd->pcidev);
+}
+
+/**
+ * ipath_setup_pe_config - setup PCIe config related stuff
+ * @dd: the infinipath device
+ * @pdev: the PCI device
+ *
+ * The pci_enable_msi() call will fail on systems with MSI quirks
+ * such as those with AMD8131, even if the device of interest is not
+ * attached to that device, (in the 2.6.13 - 2.6.15 kernels, at least, fixed
+ * late in 2.6.16).
+ * All that can be done is to edit the kernel source to remove the quirk
+ * check until that is fixed.
+ * We do not need to call enable_msi() for our HyperTransport chip,
+ * even though it uses MSI, and we want to avoid the quirk warning, so
+ * So we call enable_msi only for PCIe. If we do end up needing
+ * pci_enable_msi at some point in the future for HT, we'll move the
+ * call back into the main init_one code.
+ * We save the msi lo and hi values, so we can restore them after
+ * chip reset (the kernel PCI infrastructure doesn't yet handle that
+ * correctly).
+ */
+static int ipath_setup_pe_config(struct ipath_devdata *dd,
+ struct pci_dev *pdev)
+{
+ int pos, ret;
+
+ dd->ipath_msi_lo = 0; /* used as a flag during reset processing */
+ ret = pci_enable_msi(dd->pcidev);
+ if (ret)
+ ipath_dev_err(dd, "pci_enable_msi failed: %d, "
+ "interrupts may not work\n", ret);
+ /* continue even if it fails, we may still be OK... */
+
+ if ((pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_MSI))) {
+ u16 control;
+ pci_read_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_LO,
+ &dd->ipath_msi_lo);
+ pci_read_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_HI,
+ &dd->ipath_msi_hi);
+ pci_read_config_word(dd->pcidev, pos + PCI_MSI_FLAGS,
+ &control);
+ /* now save the data (vector) info */
+ pci_read_config_word(dd->pcidev,
+ pos + ((control & PCI_MSI_FLAGS_64BIT)
+ ? 12 : 8),
+ &dd->ipath_msi_data);
+ ipath_cdbg(VERBOSE, "Read msi data 0x%x from config offset "
+ "0x%x, control=0x%x\n", dd->ipath_msi_data,
+ pos + ((control & PCI_MSI_FLAGS_64BIT) ? 12 : 8),
+ control);
+ /* we save the cachelinesize also, although it doesn't
+ * really matter */
+ pci_read_config_byte(dd->pcidev, PCI_CACHE_LINE_SIZE,
+ &dd->ipath_pci_cacheline);
+ } else
+ ipath_dev_err(dd, "Can't find MSI capability, "
+ "can't save MSI settings for reset\n");
+ if ((pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_EXP))) {
+ u16 linkstat;
+ pci_read_config_word(dd->pcidev, pos + PCI_EXP_LNKSTA,
+ &linkstat);
+ linkstat >>= 4;
+ linkstat &= 0x1f;
+ if (linkstat != 8)
+ ipath_dev_err(dd, "PCIe width %u, "
+ "performance reduced\n", linkstat);
+ }
+ else
+ ipath_dev_err(dd, "Can't find PCI Express "
+ "capability!\n");
+ return 0;
+}
+
+static void ipath_init_pe_variables(void)
+{
+ /*
+ * bits for selecting i2c direction and values,
+ * used for I2C serial flash
+ */
+ ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM;
+ ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM;
+ ipath_gpio_sda = IPATH_GPIO_SDA;
+ ipath_gpio_scl = IPATH_GPIO_SCL;
+
+ /* variables for sanity checking interrupt and errors */
+ infinipath_hwe_bitsextant =
+ (INFINIPATH_HWE_RXEMEMPARITYERR_MASK <<
+ INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) |
+ (INFINIPATH_HWE_PCIEMEMPARITYERR_MASK <<
+ INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT) |
+ INFINIPATH_HWE_PCIE1PLLFAILED |
+ INFINIPATH_HWE_PCIE0PLLFAILED |
+ INFINIPATH_HWE_PCIEPOISONEDTLP |
+ INFINIPATH_HWE_PCIECPLTIMEOUT |
+ INFINIPATH_HWE_PCIEBUSPARITYXTLH |
+ INFINIPATH_HWE_PCIEBUSPARITYXADM |
+ INFINIPATH_HWE_PCIEBUSPARITYRADM |
+ INFINIPATH_HWE_MEMBISTFAILED |
+ INFINIPATH_HWE_COREPLL_FBSLIP |
+ INFINIPATH_HWE_COREPLL_RFSLIP |
+ INFINIPATH_HWE_SERDESPLLFAILED |
+ INFINIPATH_HWE_IBCBUSTOSPCPARITYERR |
+ INFINIPATH_HWE_IBCBUSFRSPCPARITYERR;
+ infinipath_i_bitsextant =
+ (INFINIPATH_I_RCVURG_MASK << INFINIPATH_I_RCVURG_SHIFT) |
+ (INFINIPATH_I_RCVAVAIL_MASK <<
+ INFINIPATH_I_RCVAVAIL_SHIFT) |
+ INFINIPATH_I_ERROR | INFINIPATH_I_SPIOSENT |
+ INFINIPATH_I_SPIOBUFAVAIL | INFINIPATH_I_GPIO;
+ infinipath_e_bitsextant =
+ INFINIPATH_E_RFORMATERR | INFINIPATH_E_RVCRC |
+ INFINIPATH_E_RICRC | INFINIPATH_E_RMINPKTLEN |
+ INFINIPATH_E_RMAXPKTLEN | INFINIPATH_E_RLONGPKTLEN |
+ INFINIPATH_E_RSHORTPKTLEN | INFINIPATH_E_RUNEXPCHAR |
+ INFINIPATH_E_RUNSUPVL | INFINIPATH_E_REBP |
+ INFINIPATH_E_RIBFLOW | INFINIPATH_E_RBADVERSION |
+ INFINIPATH_E_RRCVEGRFULL | INFINIPATH_E_RRCVHDRFULL |
+ INFINIPATH_E_RBADTID | INFINIPATH_E_RHDRLEN |
+ INFINIPATH_E_RHDR | INFINIPATH_E_RIBLOSTLINK |
+ INFINIPATH_E_SMINPKTLEN | INFINIPATH_E_SMAXPKTLEN |
+ INFINIPATH_E_SUNDERRUN | INFINIPATH_E_SPKTLEN |
+ INFINIPATH_E_SDROPPEDSMPPKT | INFINIPATH_E_SDROPPEDDATAPKT |
+ INFINIPATH_E_SPIOARMLAUNCH | INFINIPATH_E_SUNEXPERRPKTNUM |
+ INFINIPATH_E_SUNSUPVL | INFINIPATH_E_IBSTATUSCHANGED |
+ INFINIPATH_E_INVALIDADDR | INFINIPATH_E_RESET |
+ INFINIPATH_E_HARDWARE;
+
+ infinipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK;
+ infinipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK;
+}
+
+/* setup the MSI stuff again after a reset. I'd like to just call
+ * pci_enable_msi() and request_irq() again, but when I do that,
+ * the MSI enable bit doesn't get set in the command word, and
+ * we switch to to a different interrupt vector, which is confusing,
+ * so I instead just do it all inline. Perhaps somehow can tie this
+ * into the PCIe hotplug support at some point
+ * Note, because I'm doing it all here, I don't call pci_disable_msi()
+ * or free_irq() at the start of ipath_setup_pe_reset().
+ */
+static int ipath_reinit_msi(struct ipath_devdata *dd)
+{
+ int pos;
+ u16 control;
+ int ret;
+
+ if (!dd->ipath_msi_lo) {
+ dev_info(&dd->pcidev->dev, "Can't restore MSI config, "
+ "initial setup failed?\n");
+ ret = 0;
+ goto bail;
+ }
+
+ if (!(pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_MSI))) {
+ ipath_dev_err(dd, "Can't find MSI capability, "
+ "can't restore MSI settings\n");
+ ret = 0;
+ goto bail;
+ }
+ ipath_cdbg(VERBOSE, "Writing msi_lo 0x%x to config offset 0x%x\n",
+ dd->ipath_msi_lo, pos + PCI_MSI_ADDRESS_LO);
+ pci_write_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_LO,
+ dd->ipath_msi_lo);
+ ipath_cdbg(VERBOSE, "Writing msi_lo 0x%x to config offset 0x%x\n",
+ dd->ipath_msi_hi, pos + PCI_MSI_ADDRESS_HI);
+ pci_write_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_HI,
+ dd->ipath_msi_hi);
+ pci_read_config_word(dd->pcidev, pos + PCI_MSI_FLAGS, &control);
+ if (!(control & PCI_MSI_FLAGS_ENABLE)) {
+ ipath_cdbg(VERBOSE, "MSI control at off %x was %x, "
+ "setting MSI enable (%x)\n", pos + PCI_MSI_FLAGS,
+ control, control | PCI_MSI_FLAGS_ENABLE);
+ control |= PCI_MSI_FLAGS_ENABLE;
+ pci_write_config_word(dd->pcidev, pos + PCI_MSI_FLAGS,
+ control);
+ }
+ /* now rewrite the data (vector) info */
+ pci_write_config_word(dd->pcidev, pos +
+ ((control & PCI_MSI_FLAGS_64BIT) ? 12 : 8),
+ dd->ipath_msi_data);
+ /* we restore the cachelinesize also, although it doesn't really
+ * matter */
+ pci_write_config_byte(dd->pcidev, PCI_CACHE_LINE_SIZE,
+ dd->ipath_pci_cacheline);
+ /* and now set the pci master bit again */
+ pci_set_master(dd->pcidev);
+ ret = 1;
+
+bail:
+ return ret;
+}
+
+/* This routine sleeps, so it can only be called from user context, not
+ * from interrupt context. If we need interrupt context, we can split
+ * it into two routines.
+*/
+static int ipath_setup_pe_reset(struct ipath_devdata *dd)
+{
+ u64 val;
+ int i;
+ int ret;
+
+ /* Use ERROR so it shows up in logs, etc. */
+ ipath_dev_err(dd, "Resetting InfiniPath unit %u\n", dd->ipath_unit);
+ /* keep chip from being accessed in a few places */
+ dd->ipath_flags &= ~(IPATH_INITTED|IPATH_PRESENT);
+ val = dd->ipath_control | INFINIPATH_C_RESET;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_control, val);
+ mb();
+
+ for (i = 1; i <= 5; i++) {
+ int r;
+ /* allow MBIST, etc. to complete; longer on each retry.
+ * We sometimes get machine checks from bus timeout if no
+ * response, so for now, make it *really* long.
+ */
+ msleep(1000 + (1 + i) * 2000);
+ if ((r =
+ pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_0,
+ dd->ipath_pcibar0)))
+ ipath_dev_err(dd, "rewrite of BAR0 failed: %d\n",
+ r);
+ if ((r =
+ pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_1,
+ dd->ipath_pcibar1)))
+ ipath_dev_err(dd, "rewrite of BAR1 failed: %d\n",
+ r);
+ /* now re-enable memory access */
+ if ((r = pci_enable_device(dd->pcidev)))
+ ipath_dev_err(dd, "pci_enable_device failed after "
+ "reset: %d\n", r);
+ /* whether it worked or not, mark as present, again */
+ dd->ipath_flags |= IPATH_PRESENT;
+ val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_revision);
+ if (val == dd->ipath_revision) {
+ ipath_cdbg(VERBOSE, "Got matching revision "
+ "register %llx on try %d\n",
+ (unsigned long long) val, i);
+ ret = ipath_reinit_msi(dd);
+ goto bail;
+ }
+ /* Probably getting -1 back */
+ ipath_dbg("Didn't get expected revision register, "
+ "got %llx, try %d\n", (unsigned long long) val,
+ i + 1);
+ }
+ ret = 0; /* failed */
+
+bail:
+ return ret;
+}
+
+/**
+ * ipath_pe_put_tid - write a TID in chip
+ * @dd: the infinipath device
+ * @tidptr: pointer to the expected TID (in chip) to udpate
+ * @tidtype: 0 for eager, 1 for expected
+ * @pa: physical address of in memory buffer; ipath_tidinvalid if freeing
+ *
+ * This exists as a separate routine to allow for special locking etc.
+ * It's used for both the full cleanup on exit, as well as the normal
+ * setup and teardown.
+ */
+static void ipath_pe_put_tid(struct ipath_devdata *dd, u64 __iomem *tidptr,
+ u32 type, unsigned long pa)
+{
+ u32 __iomem *tidp32 = (u32 __iomem *)tidptr;
+ unsigned long flags = 0; /* keep gcc quiet */
+
+ if (pa != dd->ipath_tidinvalid) {
+ if (pa & ((1U << 11) - 1)) {
+ dev_info(&dd->pcidev->dev, "BUG: physaddr %lx "
+ "not 4KB aligned!\n", pa);
+ return;
+ }
+ pa >>= 11;
+ /* paranoia check */
+ if (pa & (7<<29))
+ ipath_dev_err(dd,
+ "BUG: Physical page address 0x%lx "
+ "has bits set in 31-29\n", pa);
+
+ if (type == 0)
+ pa |= dd->ipath_tidtemplate;
+ else /* for now, always full 4KB page */
+ pa |= 2 << 29;
+ }
+
+ /* workaround chip bug 9437 by writing each TID twice
+ * and holding a spinlock around the writes, so they don't
+ * intermix with other TID (eager or expected) writes
+ * Unfortunately, this call can be done from interrupt level
+ * for the port 0 eager TIDs, so we have to use irqsave
+ */
+ spin_lock_irqsave(&dd->ipath_tid_lock, flags);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_scratch, 0xfeeddeaf);
+ if (dd->ipath_kregbase)
+ writel(pa, tidp32);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_scratch, 0xdeadbeef);
+ mmiowb();
+ spin_unlock_irqrestore(&dd->ipath_tid_lock, flags);
+}
+
+/**
+ * ipath_pe_clear_tid - clear all TID entries for a port, expected and eager
+ * @dd: the infinipath device
+ * @port: the port
+ *
+ * clear all TID entries for a port, expected and eager.
+ * Used from ipath_close(). On this chip, TIDs are only 32 bits,
+ * not 64, but they are still on 64 bit boundaries, so tidbase
+ * is declared as u64 * for the pointer math, even though we write 32 bits
+ */
+static void ipath_pe_clear_tids(struct ipath_devdata *dd, unsigned port)
+{
+ u64 __iomem *tidbase;
+ unsigned long tidinv;
+ int i;
+
+ if (!dd->ipath_kregbase)
+ return;
+
+ ipath_cdbg(VERBOSE, "Invalidate TIDs for port %u\n", port);
+
+ tidinv = dd->ipath_tidinvalid;
+ tidbase = (u64 __iomem *)
+ ((char __iomem *)(dd->ipath_kregbase) +
+ dd->ipath_rcvtidbase +
+ port * dd->ipath_rcvtidcnt * sizeof(*tidbase));
+
+ for (i = 0; i < dd->ipath_rcvtidcnt; i++)
+ ipath_pe_put_tid(dd, &tidbase[i], 0, tidinv);
+
+ tidbase = (u64 __iomem *)
+ ((char __iomem *)(dd->ipath_kregbase) +
+ dd->ipath_rcvegrbase +
+ port * dd->ipath_rcvegrcnt * sizeof(*tidbase));
+
+ for (i = 0; i < dd->ipath_rcvegrcnt; i++)
+ ipath_pe_put_tid(dd, &tidbase[i], 1, tidinv);
+}
+
+/**
+ * ipath_pe_tidtemplate - setup constants for TID updates
+ * @dd: the infinipath device
+ *
+ * We setup stuff that we use a lot, to avoid calculating each time
+ */
+static void ipath_pe_tidtemplate(struct ipath_devdata *dd)
+{
+ u32 egrsize = dd->ipath_rcvegrbufsize;
+
+ /* For now, we always allocate 4KB buffers (at init) so we can
+ * receive max size packets. We may want a module parameter to
+ * specify 2KB or 4KB and/or make be per port instead of per device
+ * for those who want to reduce memory footprint. Note that the
+ * ipath_rcvhdrentsize size must be large enough to hold the largest
+ * IB header (currently 96 bytes) that we expect to handle (plus of
+ * course the 2 dwords of RHF).
+ */
+ if (egrsize == 2048)
+ dd->ipath_tidtemplate = 1U << 29;
+ else if (egrsize == 4096)
+ dd->ipath_tidtemplate = 2U << 29;
+ else {
+ egrsize = 4096;
+ dev_info(&dd->pcidev->dev, "BUG: unsupported egrbufsize "
+ "%u, using %u\n", dd->ipath_rcvegrbufsize,
+ egrsize);
+ dd->ipath_tidtemplate = 2U << 29;
+ }
+ dd->ipath_tidinvalid = 0;
+}
+
+static int ipath_pe_early_init(struct ipath_devdata *dd)
+{
+ dd->ipath_flags |= IPATH_4BYTE_TID;
+
+ /*
+ * For openfabrics, we need to be able to handle an IB header of
+ * 24 dwords. HT chip has arbitrary sized receive buffers, so we
+ * made them the same size as the PIO buffers. This chip does not
+ * handle arbitrary size buffers, so we need the header large enough
+ * to handle largest IB header, but still have room for a 2KB MTU
+ * standard IB packet.
+ */
+ dd->ipath_rcvhdrentsize = 24;
+ dd->ipath_rcvhdrsize = IPATH_DFLT_RCVHDRSIZE;
+
+ /*
+ * To truly support a 4KB MTU (for usermode), we need to
+ * bump this to a larger value. For now, we use them for
+ * the kernel only.
+ */
+ dd->ipath_rcvegrbufsize = 2048;
+ /*
+ * the min() check here is currently a nop, but it may not always
+ * be, depending on just how we do ipath_rcvegrbufsize
+ */
+ dd->ipath_ibmaxlen = min(dd->ipath_piosize2k,
+ dd->ipath_rcvegrbufsize +
+ (dd->ipath_rcvhdrentsize << 2));
+ dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen;
+
+ /*
+ * We can request a receive interrupt for 1 or
+ * more packets from current offset. For now, we set this
+ * up for a single packet.
+ */
+ dd->ipath_rhdrhead_intr_off = 1ULL<<32;
+
+ ipath_get_eeprom_info(dd);
+
+ return 0;
+}
+
+int __attribute__((weak)) ipath_unordered_wc(void)
+{
+ return 0;
+}
+
+/**
+ * ipath_init_pe_get_base_info - set chip-specific flags for user code
+ * @dd: the infinipath device
+ * @kbase: ipath_base_info pointer
+ *
+ * We set the PCIE flag because the lower bandwidth on PCIe vs
+ * HyperTransport can affect some user packet algorithims.
+ */
+static int ipath_pe_get_base_info(struct ipath_portdata *pd, void *kbase)
+{
+ struct ipath_base_info *kinfo = kbase;
+
+ if (ipath_unordered_wc()) {
+ kinfo->spi_runtime_flags |= IPATH_RUNTIME_FORCE_WC_ORDER;
+ ipath_cdbg(PROC, "Intel processor, forcing WC order\n");
+ }
+ else
+ ipath_cdbg(PROC, "Not Intel processor, WC ordered\n");
+
+ kinfo->spi_runtime_flags |= IPATH_RUNTIME_PCIE;
+
+ return 0;
+}
+
+/**
+ * ipath_init_iba6120_funcs - set up the chip-specific function pointers
+ * @dd: the infinipath device
+ *
+ * This is global, and is called directly at init to set up the
+ * chip-specific function pointers for later use.
+ */
+void ipath_init_iba6120_funcs(struct ipath_devdata *dd)
+{
+ dd->ipath_f_intrsetup = ipath_pe_intconfig;
+ dd->ipath_f_bus = ipath_setup_pe_config;
+ dd->ipath_f_reset = ipath_setup_pe_reset;
+ dd->ipath_f_get_boardname = ipath_pe_boardname;
+ dd->ipath_f_init_hwerrors = ipath_pe_init_hwerrors;
+ dd->ipath_f_early_init = ipath_pe_early_init;
+ dd->ipath_f_handle_hwerrors = ipath_pe_handle_hwerrors;
+ dd->ipath_f_quiet_serdes = ipath_pe_quiet_serdes;
+ dd->ipath_f_bringup_serdes = ipath_pe_bringup_serdes;
+ dd->ipath_f_clear_tids = ipath_pe_clear_tids;
+ dd->ipath_f_put_tid = ipath_pe_put_tid;
+ dd->ipath_f_cleanup = ipath_setup_pe_cleanup;
+ dd->ipath_f_setextled = ipath_setup_pe_setextled;
+ dd->ipath_f_get_base_info = ipath_pe_get_base_info;
+
+ /* initialize chip-specific variables */
+ dd->ipath_f_tidtemplate = ipath_pe_tidtemplate;
+
+ /*
+ * setup the register offsets, since they are different for each
+ * chip
+ */
+ dd->ipath_kregs = &ipath_pe_kregs;
+ dd->ipath_cregs = &ipath_pe_cregs;
+
+ ipath_init_pe_variables();
+}
+
u64 ipath_tidtemplate;
/* value to write to free TIDs */
u64 ipath_tidinvalid;
- /* PE-800 rcv interrupt setup */
+ /* IBA6120 rcv interrupt setup */
u64 ipath_rhdrhead_intr_off;
/* size of memory at ipath_kregbase */
int ipath_waitfor_mdio_cmdready(struct ipath_devdata *);
int ipath_waitfor_complete(struct ipath_devdata *, ipath_kreg, u64, u64 *);
u32 __iomem *ipath_getpiobuf(struct ipath_devdata *, u32 *);
-/* init PE-800-specific func */
-void ipath_init_pe800_funcs(struct ipath_devdata *);
-/* init HT-400-specific func */
-void ipath_init_ht400_funcs(struct ipath_devdata *);
+void ipath_init_iba6120_funcs(struct ipath_devdata *);
+void ipath_init_iba6110_funcs(struct ipath_devdata *);
void ipath_get_eeprom_info(struct ipath_devdata *);
u64 ipath_snap_cntr(struct ipath_devdata *, ipath_creg);
+++ /dev/null
-/*
- * Copyright (c) 2006 QLogic, Inc. All rights reserved.
- * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
- *
- * This software is available to you under a choice of one of two
- * licenses. You may choose to be licensed under the terms of the GNU
- * General Public License (GPL) Version 2, available from the file
- * COPYING in the main directory of this source tree, or the
- * OpenIB.org BSD license below:
- *
- * Redistribution and use in source and binary forms, with or
- * without modification, are permitted provided that the following
- * conditions are met:
- *
- * - Redistributions of source code must retain the above
- * copyright notice, this list of conditions and the following
- * disclaimer.
- *
- * - Redistributions in binary form must reproduce the above
- * copyright notice, this list of conditions and the following
- * disclaimer in the documentation and/or other materials
- * provided with the distribution.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
- * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
- * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
- * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
- * SOFTWARE.
- */
-/*
- * This file contains all of the code that is specific to the
- * InfiniPath PE-800 chip.
- */
-
-#include <linux/interrupt.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
-
-
-#include "ipath_kernel.h"
-#include "ipath_registers.h"
-
-/*
- * This file contains all the chip-specific register information and
- * access functions for the QLogic InfiniPath PE800, the PCI-Express chip.
- *
- * This lists the InfiniPath PE800 registers, in the actual chip layout.
- * This structure should never be directly accessed.
- */
-struct _infinipath_do_not_use_kernel_regs {
- unsigned long long Revision;
- unsigned long long Control;
- unsigned long long PageAlign;
- unsigned long long PortCnt;
- unsigned long long DebugPortSelect;
- unsigned long long Reserved0;
- unsigned long long SendRegBase;
- unsigned long long UserRegBase;
- unsigned long long CounterRegBase;
- unsigned long long Scratch;
- unsigned long long Reserved1;
- unsigned long long Reserved2;
- unsigned long long IntBlocked;
- unsigned long long IntMask;
- unsigned long long IntStatus;
- unsigned long long IntClear;
- unsigned long long ErrorMask;
- unsigned long long ErrorStatus;
- unsigned long long ErrorClear;
- unsigned long long HwErrMask;
- unsigned long long HwErrStatus;
- unsigned long long HwErrClear;
- unsigned long long HwDiagCtrl;
- unsigned long long MDIO;
- unsigned long long IBCStatus;
- unsigned long long IBCCtrl;
- unsigned long long ExtStatus;
- unsigned long long ExtCtrl;
- unsigned long long GPIOOut;
- unsigned long long GPIOMask;
- unsigned long long GPIOStatus;
- unsigned long long GPIOClear;
- unsigned long long RcvCtrl;
- unsigned long long RcvBTHQP;
- unsigned long long RcvHdrSize;
- unsigned long long RcvHdrCnt;
- unsigned long long RcvHdrEntSize;
- unsigned long long RcvTIDBase;
- unsigned long long RcvTIDCnt;
- unsigned long long RcvEgrBase;
- unsigned long long RcvEgrCnt;
- unsigned long long RcvBufBase;
- unsigned long long RcvBufSize;
- unsigned long long RxIntMemBase;
- unsigned long long RxIntMemSize;
- unsigned long long RcvPartitionKey;
- unsigned long long Reserved3;
- unsigned long long RcvPktLEDCnt;
- unsigned long long Reserved4[8];
- unsigned long long SendCtrl;
- unsigned long long SendPIOBufBase;
- unsigned long long SendPIOSize;
- unsigned long long SendPIOBufCnt;
- unsigned long long SendPIOAvailAddr;
- unsigned long long TxIntMemBase;
- unsigned long long TxIntMemSize;
- unsigned long long Reserved5;
- unsigned long long PCIeRBufTestReg0;
- unsigned long long PCIeRBufTestReg1;
- unsigned long long Reserved51[6];
- unsigned long long SendBufferError;
- unsigned long long SendBufferErrorCONT1;
- unsigned long long Reserved6SBE[6];
- unsigned long long RcvHdrAddr0;
- unsigned long long RcvHdrAddr1;
- unsigned long long RcvHdrAddr2;
- unsigned long long RcvHdrAddr3;
- unsigned long long RcvHdrAddr4;
- unsigned long long Reserved7RHA[11];
- unsigned long long RcvHdrTailAddr0;
- unsigned long long RcvHdrTailAddr1;
- unsigned long long RcvHdrTailAddr2;
- unsigned long long RcvHdrTailAddr3;
- unsigned long long RcvHdrTailAddr4;
- unsigned long long Reserved8RHTA[11];
- unsigned long long Reserved9SW[8];
- unsigned long long SerdesConfig0;
- unsigned long long SerdesConfig1;
- unsigned long long SerdesStatus;
- unsigned long long XGXSConfig;
- unsigned long long IBPLLCfg;
- unsigned long long Reserved10SW2[3];
- unsigned long long PCIEQ0SerdesConfig0;
- unsigned long long PCIEQ0SerdesConfig1;
- unsigned long long PCIEQ0SerdesStatus;
- unsigned long long Reserved11;
- unsigned long long PCIEQ1SerdesConfig0;
- unsigned long long PCIEQ1SerdesConfig1;
- unsigned long long PCIEQ1SerdesStatus;
- unsigned long long Reserved12;
-};
-
-#define IPATH_KREG_OFFSET(field) (offsetof(struct \
- _infinipath_do_not_use_kernel_regs, field) / sizeof(u64))
-#define IPATH_CREG_OFFSET(field) (offsetof( \
- struct infinipath_counters, field) / sizeof(u64))
-
-static const struct ipath_kregs ipath_pe_kregs = {
- .kr_control = IPATH_KREG_OFFSET(Control),
- .kr_counterregbase = IPATH_KREG_OFFSET(CounterRegBase),
- .kr_debugportselect = IPATH_KREG_OFFSET(DebugPortSelect),
- .kr_errorclear = IPATH_KREG_OFFSET(ErrorClear),
- .kr_errormask = IPATH_KREG_OFFSET(ErrorMask),
- .kr_errorstatus = IPATH_KREG_OFFSET(ErrorStatus),
- .kr_extctrl = IPATH_KREG_OFFSET(ExtCtrl),
- .kr_extstatus = IPATH_KREG_OFFSET(ExtStatus),
- .kr_gpio_clear = IPATH_KREG_OFFSET(GPIOClear),
- .kr_gpio_mask = IPATH_KREG_OFFSET(GPIOMask),
- .kr_gpio_out = IPATH_KREG_OFFSET(GPIOOut),
- .kr_gpio_status = IPATH_KREG_OFFSET(GPIOStatus),
- .kr_hwdiagctrl = IPATH_KREG_OFFSET(HwDiagCtrl),
- .kr_hwerrclear = IPATH_KREG_OFFSET(HwErrClear),
- .kr_hwerrmask = IPATH_KREG_OFFSET(HwErrMask),
- .kr_hwerrstatus = IPATH_KREG_OFFSET(HwErrStatus),
- .kr_ibcctrl = IPATH_KREG_OFFSET(IBCCtrl),
- .kr_ibcstatus = IPATH_KREG_OFFSET(IBCStatus),
- .kr_intblocked = IPATH_KREG_OFFSET(IntBlocked),
- .kr_intclear = IPATH_KREG_OFFSET(IntClear),
- .kr_intmask = IPATH_KREG_OFFSET(IntMask),
- .kr_intstatus = IPATH_KREG_OFFSET(IntStatus),
- .kr_mdio = IPATH_KREG_OFFSET(MDIO),
- .kr_pagealign = IPATH_KREG_OFFSET(PageAlign),
- .kr_partitionkey = IPATH_KREG_OFFSET(RcvPartitionKey),
- .kr_portcnt = IPATH_KREG_OFFSET(PortCnt),
- .kr_rcvbthqp = IPATH_KREG_OFFSET(RcvBTHQP),
- .kr_rcvbufbase = IPATH_KREG_OFFSET(RcvBufBase),
- .kr_rcvbufsize = IPATH_KREG_OFFSET(RcvBufSize),
- .kr_rcvctrl = IPATH_KREG_OFFSET(RcvCtrl),
- .kr_rcvegrbase = IPATH_KREG_OFFSET(RcvEgrBase),
- .kr_rcvegrcnt = IPATH_KREG_OFFSET(RcvEgrCnt),
- .kr_rcvhdrcnt = IPATH_KREG_OFFSET(RcvHdrCnt),
- .kr_rcvhdrentsize = IPATH_KREG_OFFSET(RcvHdrEntSize),
- .kr_rcvhdrsize = IPATH_KREG_OFFSET(RcvHdrSize),
- .kr_rcvintmembase = IPATH_KREG_OFFSET(RxIntMemBase),
- .kr_rcvintmemsize = IPATH_KREG_OFFSET(RxIntMemSize),
- .kr_rcvtidbase = IPATH_KREG_OFFSET(RcvTIDBase),
- .kr_rcvtidcnt = IPATH_KREG_OFFSET(RcvTIDCnt),
- .kr_revision = IPATH_KREG_OFFSET(Revision),
- .kr_scratch = IPATH_KREG_OFFSET(Scratch),
- .kr_sendbuffererror = IPATH_KREG_OFFSET(SendBufferError),
- .kr_sendctrl = IPATH_KREG_OFFSET(SendCtrl),
- .kr_sendpioavailaddr = IPATH_KREG_OFFSET(SendPIOAvailAddr),
- .kr_sendpiobufbase = IPATH_KREG_OFFSET(SendPIOBufBase),
- .kr_sendpiobufcnt = IPATH_KREG_OFFSET(SendPIOBufCnt),
- .kr_sendpiosize = IPATH_KREG_OFFSET(SendPIOSize),
- .kr_sendregbase = IPATH_KREG_OFFSET(SendRegBase),
- .kr_txintmembase = IPATH_KREG_OFFSET(TxIntMemBase),
- .kr_txintmemsize = IPATH_KREG_OFFSET(TxIntMemSize),
- .kr_userregbase = IPATH_KREG_OFFSET(UserRegBase),
- .kr_serdesconfig0 = IPATH_KREG_OFFSET(SerdesConfig0),
- .kr_serdesconfig1 = IPATH_KREG_OFFSET(SerdesConfig1),
- .kr_serdesstatus = IPATH_KREG_OFFSET(SerdesStatus),
- .kr_xgxsconfig = IPATH_KREG_OFFSET(XGXSConfig),
- .kr_ibpllcfg = IPATH_KREG_OFFSET(IBPLLCfg),
-
- /*
- * These should not be used directly via ipath_read_kreg64(),
- * use them with ipath_read_kreg64_port()
- */
- .kr_rcvhdraddr = IPATH_KREG_OFFSET(RcvHdrAddr0),
- .kr_rcvhdrtailaddr = IPATH_KREG_OFFSET(RcvHdrTailAddr0),
-
- /* This group is pe-800-specific; and used only in this file */
- /* The rcvpktled register controls one of the debug port signals, so
- * a packet activity LED can be connected to it. */
- .kr_rcvpktledcnt = IPATH_KREG_OFFSET(RcvPktLEDCnt),
- .kr_pcierbuftestreg0 = IPATH_KREG_OFFSET(PCIeRBufTestReg0),
- .kr_pcierbuftestreg1 = IPATH_KREG_OFFSET(PCIeRBufTestReg1),
- .kr_pcieq0serdesconfig0 = IPATH_KREG_OFFSET(PCIEQ0SerdesConfig0),
- .kr_pcieq0serdesconfig1 = IPATH_KREG_OFFSET(PCIEQ0SerdesConfig1),
- .kr_pcieq0serdesstatus = IPATH_KREG_OFFSET(PCIEQ0SerdesStatus),
- .kr_pcieq1serdesconfig0 = IPATH_KREG_OFFSET(PCIEQ1SerdesConfig0),
- .kr_pcieq1serdesconfig1 = IPATH_KREG_OFFSET(PCIEQ1SerdesConfig1),
- .kr_pcieq1serdesstatus = IPATH_KREG_OFFSET(PCIEQ1SerdesStatus)
-};
-
-static const struct ipath_cregs ipath_pe_cregs = {
- .cr_badformatcnt = IPATH_CREG_OFFSET(RxBadFormatCnt),
- .cr_erricrccnt = IPATH_CREG_OFFSET(RxICRCErrCnt),
- .cr_errlinkcnt = IPATH_CREG_OFFSET(RxLinkProblemCnt),
- .cr_errlpcrccnt = IPATH_CREG_OFFSET(RxLPCRCErrCnt),
- .cr_errpkey = IPATH_CREG_OFFSET(RxPKeyMismatchCnt),
- .cr_errrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowCtrlErrCnt),
- .cr_err_rlencnt = IPATH_CREG_OFFSET(RxLenErrCnt),
- .cr_errslencnt = IPATH_CREG_OFFSET(TxLenErrCnt),
- .cr_errtidfull = IPATH_CREG_OFFSET(RxTIDFullErrCnt),
- .cr_errtidvalid = IPATH_CREG_OFFSET(RxTIDValidErrCnt),
- .cr_errvcrccnt = IPATH_CREG_OFFSET(RxVCRCErrCnt),
- .cr_ibstatuschange = IPATH_CREG_OFFSET(IBStatusChangeCnt),
- .cr_intcnt = IPATH_CREG_OFFSET(LBIntCnt),
- .cr_invalidrlencnt = IPATH_CREG_OFFSET(RxMaxMinLenErrCnt),
- .cr_invalidslencnt = IPATH_CREG_OFFSET(TxMaxMinLenErrCnt),
- .cr_lbflowstallcnt = IPATH_CREG_OFFSET(LBFlowStallCnt),
- .cr_pktrcvcnt = IPATH_CREG_OFFSET(RxDataPktCnt),
- .cr_pktrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowPktCnt),
- .cr_pktsendcnt = IPATH_CREG_OFFSET(TxDataPktCnt),
- .cr_pktsendflowcnt = IPATH_CREG_OFFSET(TxFlowPktCnt),
- .cr_portovflcnt = IPATH_CREG_OFFSET(RxP0HdrEgrOvflCnt),
- .cr_rcvebpcnt = IPATH_CREG_OFFSET(RxEBPCnt),
- .cr_rcvovflcnt = IPATH_CREG_OFFSET(RxBufOvflCnt),
- .cr_senddropped = IPATH_CREG_OFFSET(TxDroppedPktCnt),
- .cr_sendstallcnt = IPATH_CREG_OFFSET(TxFlowStallCnt),
- .cr_sendunderruncnt = IPATH_CREG_OFFSET(TxUnderrunCnt),
- .cr_wordrcvcnt = IPATH_CREG_OFFSET(RxDwordCnt),
- .cr_wordsendcnt = IPATH_CREG_OFFSET(TxDwordCnt),
- .cr_unsupvlcnt = IPATH_CREG_OFFSET(TxUnsupVLErrCnt),
- .cr_rxdroppktcnt = IPATH_CREG_OFFSET(RxDroppedPktCnt),
- .cr_iblinkerrrecovcnt = IPATH_CREG_OFFSET(IBLinkErrRecoveryCnt),
- .cr_iblinkdowncnt = IPATH_CREG_OFFSET(IBLinkDownedCnt),
- .cr_ibsymbolerrcnt = IPATH_CREG_OFFSET(IBSymbolErrCnt)
-};
-
-/* kr_intstatus, kr_intclear, kr_intmask bits */
-#define INFINIPATH_I_RCVURG_MASK 0x1F
-#define INFINIPATH_I_RCVAVAIL_MASK 0x1F
-
-/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */
-#define INFINIPATH_HWE_PCIEMEMPARITYERR_MASK 0x000000000000003fULL
-#define INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT 0
-#define INFINIPATH_HWE_PCIEPOISONEDTLP 0x0000000010000000ULL
-#define INFINIPATH_HWE_PCIECPLTIMEOUT 0x0000000020000000ULL
-#define INFINIPATH_HWE_PCIEBUSPARITYXTLH 0x0000000040000000ULL
-#define INFINIPATH_HWE_PCIEBUSPARITYXADM 0x0000000080000000ULL
-#define INFINIPATH_HWE_PCIEBUSPARITYRADM 0x0000000100000000ULL
-#define INFINIPATH_HWE_COREPLL_FBSLIP 0x0080000000000000ULL
-#define INFINIPATH_HWE_COREPLL_RFSLIP 0x0100000000000000ULL
-#define INFINIPATH_HWE_PCIE1PLLFAILED 0x0400000000000000ULL
-#define INFINIPATH_HWE_PCIE0PLLFAILED 0x0800000000000000ULL
-#define INFINIPATH_HWE_SERDESPLLFAILED 0x1000000000000000ULL
-
-/* kr_extstatus bits */
-#define INFINIPATH_EXTS_FREQSEL 0x2
-#define INFINIPATH_EXTS_SERDESSEL 0x4
-#define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000
-#define INFINIPATH_EXTS_MEMBIST_FOUND 0x0000000000008000
-
-#define _IPATH_GPIO_SDA_NUM 1
-#define _IPATH_GPIO_SCL_NUM 0
-
-#define IPATH_GPIO_SDA (1ULL << \
- (_IPATH_GPIO_SDA_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
-#define IPATH_GPIO_SCL (1ULL << \
- (_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
-
-/**
- * ipath_pe_handle_hwerrors - display hardware errors.
- * @dd: the infinipath device
- * @msg: the output buffer
- * @msgl: the size of the output buffer
- *
- * Use same msg buffer as regular errors to avoid excessive stack
- * use. Most hardware errors are catastrophic, but for right now,
- * we'll print them and continue. We reuse the same message buffer as
- * ipath_handle_errors() to avoid excessive stack usage.
- */
-static void ipath_pe_handle_hwerrors(struct ipath_devdata *dd, char *msg,
- size_t msgl)
-{
- ipath_err_t hwerrs;
- u32 bits, ctrl;
- int isfatal = 0;
- char bitsmsg[64];
-
- hwerrs = ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus);
- if (!hwerrs) {
- /*
- * better than printing cofusing messages
- * This seems to be related to clearing the crc error, or
- * the pll error during init.
- */
- ipath_cdbg(VERBOSE, "Called but no hardware errors set\n");
- return;
- } else if (hwerrs == ~0ULL) {
- ipath_dev_err(dd, "Read of hardware error status failed "
- "(all bits set); ignoring\n");
- return;
- }
- ipath_stats.sps_hwerrs++;
-
- /* Always clear the error status register, except MEMBISTFAIL,
- * regardless of whether we continue or stop using the chip.
- * We want that set so we know it failed, even across driver reload.
- * We'll still ignore it in the hwerrmask. We do this partly for
- * diagnostics, but also for support */
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
- hwerrs&~INFINIPATH_HWE_MEMBISTFAILED);
-
- hwerrs &= dd->ipath_hwerrmask;
-
- /*
- * make sure we get this much out, unless told to be quiet,
- * or it's occurred within the last 5 seconds
- */
- if ((hwerrs & ~dd->ipath_lasthwerror) ||
- (ipath_debug & __IPATH_VERBDBG))
- dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx "
- "(cleared)\n", (unsigned long long) hwerrs);
- dd->ipath_lasthwerror |= hwerrs;
-
- if (hwerrs & ~infinipath_hwe_bitsextant)
- ipath_dev_err(dd, "hwerror interrupt with unknown errors "
- "%llx set\n", (unsigned long long)
- (hwerrs & ~infinipath_hwe_bitsextant));
-
- ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control);
- if (ctrl & INFINIPATH_C_FREEZEMODE) {
- if (hwerrs) {
- /*
- * if any set that we aren't ignoring only make the
- * complaint once, in case it's stuck or recurring,
- * and we get here multiple times
- */
- if (dd->ipath_flags & IPATH_INITTED) {
- ipath_dev_err(dd, "Fatal Error (freeze "
- "mode), no longer usable\n");
- isfatal = 1;
- }
- /*
- * Mark as having had an error for driver, and also
- * for /sys and status word mapped to user programs.
- * This marks unit as not usable, until reset
- */
- *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY;
- *dd->ipath_statusp |= IPATH_STATUS_HWERROR;
- dd->ipath_flags &= ~IPATH_INITTED;
- } else {
- ipath_dbg("Clearing freezemode on ignored hardware "
- "error\n");
- ctrl &= ~INFINIPATH_C_FREEZEMODE;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
- ctrl);
- }
- }
-
- *msg = '\0';
-
- if (hwerrs & INFINIPATH_HWE_MEMBISTFAILED) {
- strlcat(msg, "[Memory BIST test failed, PE-800 unusable]",
- msgl);
- /* ignore from now on, so disable until driver reloaded */
- *dd->ipath_statusp |= IPATH_STATUS_HWERROR;
- dd->ipath_hwerrmask &= ~INFINIPATH_HWE_MEMBISTFAILED;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
- dd->ipath_hwerrmask);
- }
- if (hwerrs & (INFINIPATH_HWE_RXEMEMPARITYERR_MASK
- << INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT)) {
- bits = (u32) ((hwerrs >>
- INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) &
- INFINIPATH_HWE_RXEMEMPARITYERR_MASK);
- snprintf(bitsmsg, sizeof bitsmsg, "[RXE Parity Errs %x] ",
- bits);
- strlcat(msg, bitsmsg, msgl);
- }
- if (hwerrs & (INFINIPATH_HWE_TXEMEMPARITYERR_MASK
- << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)) {
- bits = (u32) ((hwerrs >>
- INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) &
- INFINIPATH_HWE_TXEMEMPARITYERR_MASK);
- snprintf(bitsmsg, sizeof bitsmsg, "[TXE Parity Errs %x] ",
- bits);
- strlcat(msg, bitsmsg, msgl);
- }
- if (hwerrs & (INFINIPATH_HWE_PCIEMEMPARITYERR_MASK
- << INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT)) {
- bits = (u32) ((hwerrs >>
- INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT) &
- INFINIPATH_HWE_PCIEMEMPARITYERR_MASK);
- snprintf(bitsmsg, sizeof bitsmsg,
- "[PCIe Mem Parity Errs %x] ", bits);
- strlcat(msg, bitsmsg, msgl);
- }
- if (hwerrs & INFINIPATH_HWE_IBCBUSTOSPCPARITYERR)
- strlcat(msg, "[IB2IPATH Parity]", msgl);
- if (hwerrs & INFINIPATH_HWE_IBCBUSFRSPCPARITYERR)
- strlcat(msg, "[IPATH2IB Parity]", msgl);
-
-#define _IPATH_PLL_FAIL (INFINIPATH_HWE_COREPLL_FBSLIP | \
- INFINIPATH_HWE_COREPLL_RFSLIP )
-
- if (hwerrs & _IPATH_PLL_FAIL) {
- snprintf(bitsmsg, sizeof bitsmsg,
- "[PLL failed (%llx), PE-800 unusable]",
- (unsigned long long) hwerrs & _IPATH_PLL_FAIL);
- strlcat(msg, bitsmsg, msgl);
- /* ignore from now on, so disable until driver reloaded */
- dd->ipath_hwerrmask &= ~(hwerrs & _IPATH_PLL_FAIL);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
- dd->ipath_hwerrmask);
- }
-
- if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED) {
- /*
- * If it occurs, it is left masked since the eternal
- * interface is unused
- */
- dd->ipath_hwerrmask &= ~INFINIPATH_HWE_SERDESPLLFAILED;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
- dd->ipath_hwerrmask);
- }
-
- if (hwerrs & INFINIPATH_HWE_PCIEPOISONEDTLP)
- strlcat(msg, "[PCIe Poisoned TLP]", msgl);
- if (hwerrs & INFINIPATH_HWE_PCIECPLTIMEOUT)
- strlcat(msg, "[PCIe completion timeout]", msgl);
-
- /*
- * In practice, it's unlikely wthat we'll see PCIe PLL, or bus
- * parity or memory parity error failures, because most likely we
- * won't be able to talk to the core of the chip. Nonetheless, we
- * might see them, if they are in parts of the PCIe core that aren't
- * essential.
- */
- if (hwerrs & INFINIPATH_HWE_PCIE1PLLFAILED)
- strlcat(msg, "[PCIePLL1]", msgl);
- if (hwerrs & INFINIPATH_HWE_PCIE0PLLFAILED)
- strlcat(msg, "[PCIePLL0]", msgl);
- if (hwerrs & INFINIPATH_HWE_PCIEBUSPARITYXTLH)
- strlcat(msg, "[PCIe XTLH core parity]", msgl);
- if (hwerrs & INFINIPATH_HWE_PCIEBUSPARITYXADM)
- strlcat(msg, "[PCIe ADM TX core parity]", msgl);
- if (hwerrs & INFINIPATH_HWE_PCIEBUSPARITYRADM)
- strlcat(msg, "[PCIe ADM RX core parity]", msgl);
-
- if (hwerrs & INFINIPATH_HWE_RXDSYNCMEMPARITYERR)
- strlcat(msg, "[Rx Dsync]", msgl);
- if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED)
- strlcat(msg, "[SerDes PLL]", msgl);
-
- ipath_dev_err(dd, "%s hardware error\n", msg);
- if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg) {
- /*
- * for /sys status file ; if no trailing } is copied, we'll
- * know it was truncated.
- */
- snprintf(dd->ipath_freezemsg, dd->ipath_freezelen,
- "{%s}", msg);
- }
-}
-
-/**
- * ipath_pe_boardname - fill in the board name
- * @dd: the infinipath device
- * @name: the output buffer
- * @namelen: the size of the output buffer
- *
- * info is based on the board revision register
- */
-static int ipath_pe_boardname(struct ipath_devdata *dd, char *name,
- size_t namelen)
-{
- char *n = NULL;
- u8 boardrev = dd->ipath_boardrev;
- int ret;
-
- switch (boardrev) {
- case 0:
- n = "InfiniPath_Emulation";
- break;
- case 1:
- n = "InfiniPath_PE-800-Bringup";
- break;
- case 2:
- n = "InfiniPath_PE-880";
- break;
- case 3:
- n = "InfiniPath_PE-850";
- break;
- case 4:
- n = "InfiniPath_PE-860";
- break;
- default:
- ipath_dev_err(dd,
- "Don't yet know about board with ID %u\n",
- boardrev);
- snprintf(name, namelen, "Unknown_InfiniPath_PE-8xx_%u",
- boardrev);
- break;
- }
- if (n)
- snprintf(name, namelen, "%s", n);
-
- if (dd->ipath_majrev != 4 || !dd->ipath_minrev || dd->ipath_minrev>2) {
- ipath_dev_err(dd, "Unsupported PE-800 revision %u.%u!\n",
- dd->ipath_majrev, dd->ipath_minrev);
- ret = 1;
- } else
- ret = 0;
-
- return ret;
-}
-
-/**
- * ipath_pe_init_hwerrors - enable hardware errors
- * @dd: the infinipath device
- *
- * now that we have finished initializing everything that might reasonably
- * cause a hardware error, and cleared those errors bits as they occur,
- * we can enable hardware errors in the mask (potentially enabling
- * freeze mode), and enable hardware errors as errors (along with
- * everything else) in errormask
- */
-static void ipath_pe_init_hwerrors(struct ipath_devdata *dd)
-{
- ipath_err_t val;
- u64 extsval;
-
- extsval = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
-
- if (!(extsval & INFINIPATH_EXTS_MEMBIST_ENDTEST))
- ipath_dev_err(dd, "MemBIST did not complete!\n");
-
- val = ~0ULL; /* barring bugs, all hwerrors become interrupts, */
-
- if (!dd->ipath_boardrev) // no PLL for Emulator
- val &= ~INFINIPATH_HWE_SERDESPLLFAILED;
-
- /* workaround bug 9460 in internal interface bus parity checking */
- val &= ~INFINIPATH_HWE_PCIEBUSPARITYRADM;
-
- dd->ipath_hwerrmask = val;
-}
-
-/**
- * ipath_pe_bringup_serdes - bring up the serdes
- * @dd: the infinipath device
- */
-static int ipath_pe_bringup_serdes(struct ipath_devdata *dd)
-{
- u64 val, tmp, config1;
- int ret = 0, change = 0;
-
- ipath_dbg("Trying to bringup serdes\n");
-
- if (ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus) &
- INFINIPATH_HWE_SERDESPLLFAILED) {
- ipath_dbg("At start, serdes PLL failed bit set "
- "in hwerrstatus, clearing and continuing\n");
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
- INFINIPATH_HWE_SERDESPLLFAILED);
- }
-
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
- config1 = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig1);
-
- ipath_cdbg(VERBOSE, "SerDes status config0=%llx config1=%llx, "
- "xgxsconfig %llx\n", (unsigned long long) val,
- (unsigned long long) config1, (unsigned long long)
- ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
-
- /*
- * Force reset on, also set rxdetect enable. Must do before reading
- * serdesstatus at least for simulation, or some of the bits in
- * serdes status will come back as undefined and cause simulation
- * failures
- */
- val |= INFINIPATH_SERDC0_RESET_PLL | INFINIPATH_SERDC0_RXDETECT_EN
- | INFINIPATH_SERDC0_L1PWR_DN;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
- /* be sure chip saw it */
- tmp = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
- udelay(5); /* need pll reset set at least for a bit */
- /*
- * after PLL is reset, set the per-lane Resets and TxIdle and
- * clear the PLL reset and rxdetect (to get falling edge).
- * Leave L1PWR bits set (permanently)
- */
- val &= ~(INFINIPATH_SERDC0_RXDETECT_EN | INFINIPATH_SERDC0_RESET_PLL
- | INFINIPATH_SERDC0_L1PWR_DN);
- val |= INFINIPATH_SERDC0_RESET_MASK | INFINIPATH_SERDC0_TXIDLE;
- ipath_cdbg(VERBOSE, "Clearing pll reset and setting lane resets "
- "and txidle (%llx)\n", (unsigned long long) val);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
- /* be sure chip saw it */
- tmp = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
- /* need PLL reset clear for at least 11 usec before lane
- * resets cleared; give it a few more to be sure */
- udelay(15);
- val &= ~(INFINIPATH_SERDC0_RESET_MASK | INFINIPATH_SERDC0_TXIDLE);
-
- ipath_cdbg(VERBOSE, "Clearing lane resets and txidle "
- "(writing %llx)\n", (unsigned long long) val);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
- /* be sure chip saw it */
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
-
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
- if (((val >> INFINIPATH_XGXS_MDIOADDR_SHIFT) &
- INFINIPATH_XGXS_MDIOADDR_MASK) != 3) {
- val &=
- ~(INFINIPATH_XGXS_MDIOADDR_MASK <<
- INFINIPATH_XGXS_MDIOADDR_SHIFT);
- /* MDIO address 3 */
- val |= 3ULL << INFINIPATH_XGXS_MDIOADDR_SHIFT;
- change = 1;
- }
- if (val & INFINIPATH_XGXS_RESET) {
- val &= ~INFINIPATH_XGXS_RESET;
- change = 1;
- }
- if (change)
- ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
-
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
-
- /* clear current and de-emphasis bits */
- config1 &= ~0x0ffffffff00ULL;
- /* set current to 20ma */
- config1 |= 0x00000000000ULL;
- /* set de-emphasis to -5.68dB */
- config1 |= 0x0cccc000000ULL;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig1, config1);
-
- ipath_cdbg(VERBOSE, "done: SerDes status config0=%llx "
- "config1=%llx, sstatus=%llx xgxs=%llx\n",
- (unsigned long long) val, (unsigned long long) config1,
- (unsigned long long)
- ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesstatus),
- (unsigned long long)
- ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
-
- if (!ipath_waitfor_mdio_cmdready(dd)) {
- ipath_write_kreg(
- dd, dd->ipath_kregs->kr_mdio,
- ipath_mdio_req(IPATH_MDIO_CMD_READ, 31,
- IPATH_MDIO_CTRL_XGXS_REG_8, 0));
- if (ipath_waitfor_complete(dd, dd->ipath_kregs->kr_mdio,
- IPATH_MDIO_DATAVALID, &val))
- ipath_dbg("Never got MDIO data for XGXS "
- "status read\n");
- else
- ipath_cdbg(VERBOSE, "MDIO Read reg8, "
- "'bank' 31 %x\n", (u32) val);
- } else
- ipath_dbg("Never got MDIO cmdready for XGXS status read\n");
-
- return ret;
-}
-
-/**
- * ipath_pe_quiet_serdes - set serdes to txidle
- * @dd: the infinipath device
- * Called when driver is being unloaded
- */
-static void ipath_pe_quiet_serdes(struct ipath_devdata *dd)
-{
- u64 val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
-
- val |= INFINIPATH_SERDC0_TXIDLE;
- ipath_dbg("Setting TxIdleEn on serdes (config0 = %llx)\n",
- (unsigned long long) val);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
-}
-
-/* this is not yet needed on the PE800, so just return 0. */
-static int ipath_pe_intconfig(struct ipath_devdata *dd)
-{
- return 0;
-}
-
-/**
- * ipath_setup_pe_setextled - set the state of the two external LEDs
- * @dd: the infinipath device
- * @lst: the L state
- * @ltst: the LT state
-
- * These LEDs indicate the physical and logical state of IB link.
- * For this chip (at least with recommended board pinouts), LED1
- * is Yellow (logical state) and LED2 is Green (physical state),
- *
- * Note: We try to match the Mellanox HCA LED behavior as best
- * we can. Green indicates physical link state is OK (something is
- * plugged in, and we can train).
- * Amber indicates the link is logically up (ACTIVE).
- * Mellanox further blinks the amber LED to indicate data packet
- * activity, but we have no hardware support for that, so it would
- * require waking up every 10-20 msecs and checking the counters
- * on the chip, and then turning the LED off if appropriate. That's
- * visible overhead, so not something we will do.
- *
- */
-static void ipath_setup_pe_setextled(struct ipath_devdata *dd, u64 lst,
- u64 ltst)
-{
- u64 extctl;
-
- /* the diags use the LED to indicate diag info, so we leave
- * the external LED alone when the diags are running */
- if (ipath_diag_inuse)
- return;
-
- extctl = dd->ipath_extctrl & ~(INFINIPATH_EXTC_LED1PRIPORT_ON |
- INFINIPATH_EXTC_LED2PRIPORT_ON);
-
- if (ltst & INFINIPATH_IBCS_LT_STATE_LINKUP)
- extctl |= INFINIPATH_EXTC_LED2PRIPORT_ON;
- if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
- extctl |= INFINIPATH_EXTC_LED1PRIPORT_ON;
- dd->ipath_extctrl = extctl;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, extctl);
-}
-
-/**
- * ipath_setup_pe_cleanup - clean up any per-chip chip-specific stuff
- * @dd: the infinipath device
- *
- * This is called during driver unload.
- * We do the pci_disable_msi here, not in generic code, because it
- * isn't used for the HT-400. If we do end up needing pci_enable_msi
- * at some point in the future for HT-400, we'll move the call back
- * into the main init_one code.
- */
-static void ipath_setup_pe_cleanup(struct ipath_devdata *dd)
-{
- dd->ipath_msi_lo = 0; /* just in case unload fails */
- pci_disable_msi(dd->pcidev);
-}
-
-/**
- * ipath_setup_pe_config - setup PCIe config related stuff
- * @dd: the infinipath device
- * @pdev: the PCI device
- *
- * The pci_enable_msi() call will fail on systems with MSI quirks
- * such as those with AMD8131, even if the device of interest is not
- * attached to that device, (in the 2.6.13 - 2.6.15 kernels, at least, fixed
- * late in 2.6.16).
- * All that can be done is to edit the kernel source to remove the quirk
- * check until that is fixed.
- * We do not need to call enable_msi() for our HyperTransport chip (HT-400),
- * even those it uses MSI, and we want to avoid the quirk warning, so
- * So we call enable_msi only for the PE-800. If we do end up needing
- * pci_enable_msi at some point in the future for HT-400, we'll move the
- * call back into the main init_one code.
- * We save the msi lo and hi values, so we can restore them after
- * chip reset (the kernel PCI infrastructure doesn't yet handle that
- * correctly).
- */
-static int ipath_setup_pe_config(struct ipath_devdata *dd,
- struct pci_dev *pdev)
-{
- int pos, ret;
-
- dd->ipath_msi_lo = 0; /* used as a flag during reset processing */
- ret = pci_enable_msi(dd->pcidev);
- if (ret)
- ipath_dev_err(dd, "pci_enable_msi failed: %d, "
- "interrupts may not work\n", ret);
- /* continue even if it fails, we may still be OK... */
-
- if ((pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_MSI))) {
- u16 control;
- pci_read_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_LO,
- &dd->ipath_msi_lo);
- pci_read_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_HI,
- &dd->ipath_msi_hi);
- pci_read_config_word(dd->pcidev, pos + PCI_MSI_FLAGS,
- &control);
- /* now save the data (vector) info */
- pci_read_config_word(dd->pcidev,
- pos + ((control & PCI_MSI_FLAGS_64BIT)
- ? 12 : 8),
- &dd->ipath_msi_data);
- ipath_cdbg(VERBOSE, "Read msi data 0x%x from config offset "
- "0x%x, control=0x%x\n", dd->ipath_msi_data,
- pos + ((control & PCI_MSI_FLAGS_64BIT) ? 12 : 8),
- control);
- /* we save the cachelinesize also, although it doesn't
- * really matter */
- pci_read_config_byte(dd->pcidev, PCI_CACHE_LINE_SIZE,
- &dd->ipath_pci_cacheline);
- } else
- ipath_dev_err(dd, "Can't find MSI capability, "
- "can't save MSI settings for reset\n");
- if ((pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_EXP))) {
- u16 linkstat;
- pci_read_config_word(dd->pcidev, pos + PCI_EXP_LNKSTA,
- &linkstat);
- linkstat >>= 4;
- linkstat &= 0x1f;
- if (linkstat != 8)
- ipath_dev_err(dd, "PCIe width %u, "
- "performance reduced\n", linkstat);
- }
- else
- ipath_dev_err(dd, "Can't find PCI Express "
- "capability!\n");
- return 0;
-}
-
-static void ipath_init_pe_variables(void)
-{
- /*
- * bits for selecting i2c direction and values,
- * used for I2C serial flash
- */
- ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM;
- ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM;
- ipath_gpio_sda = IPATH_GPIO_SDA;
- ipath_gpio_scl = IPATH_GPIO_SCL;
-
- /* variables for sanity checking interrupt and errors */
- infinipath_hwe_bitsextant =
- (INFINIPATH_HWE_RXEMEMPARITYERR_MASK <<
- INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) |
- (INFINIPATH_HWE_PCIEMEMPARITYERR_MASK <<
- INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT) |
- INFINIPATH_HWE_PCIE1PLLFAILED |
- INFINIPATH_HWE_PCIE0PLLFAILED |
- INFINIPATH_HWE_PCIEPOISONEDTLP |
- INFINIPATH_HWE_PCIECPLTIMEOUT |
- INFINIPATH_HWE_PCIEBUSPARITYXTLH |
- INFINIPATH_HWE_PCIEBUSPARITYXADM |
- INFINIPATH_HWE_PCIEBUSPARITYRADM |
- INFINIPATH_HWE_MEMBISTFAILED |
- INFINIPATH_HWE_COREPLL_FBSLIP |
- INFINIPATH_HWE_COREPLL_RFSLIP |
- INFINIPATH_HWE_SERDESPLLFAILED |
- INFINIPATH_HWE_IBCBUSTOSPCPARITYERR |
- INFINIPATH_HWE_IBCBUSFRSPCPARITYERR;
- infinipath_i_bitsextant =
- (INFINIPATH_I_RCVURG_MASK << INFINIPATH_I_RCVURG_SHIFT) |
- (INFINIPATH_I_RCVAVAIL_MASK <<
- INFINIPATH_I_RCVAVAIL_SHIFT) |
- INFINIPATH_I_ERROR | INFINIPATH_I_SPIOSENT |
- INFINIPATH_I_SPIOBUFAVAIL | INFINIPATH_I_GPIO;
- infinipath_e_bitsextant =
- INFINIPATH_E_RFORMATERR | INFINIPATH_E_RVCRC |
- INFINIPATH_E_RICRC | INFINIPATH_E_RMINPKTLEN |
- INFINIPATH_E_RMAXPKTLEN | INFINIPATH_E_RLONGPKTLEN |
- INFINIPATH_E_RSHORTPKTLEN | INFINIPATH_E_RUNEXPCHAR |
- INFINIPATH_E_RUNSUPVL | INFINIPATH_E_REBP |
- INFINIPATH_E_RIBFLOW | INFINIPATH_E_RBADVERSION |
- INFINIPATH_E_RRCVEGRFULL | INFINIPATH_E_RRCVHDRFULL |
- INFINIPATH_E_RBADTID | INFINIPATH_E_RHDRLEN |
- INFINIPATH_E_RHDR | INFINIPATH_E_RIBLOSTLINK |
- INFINIPATH_E_SMINPKTLEN | INFINIPATH_E_SMAXPKTLEN |
- INFINIPATH_E_SUNDERRUN | INFINIPATH_E_SPKTLEN |
- INFINIPATH_E_SDROPPEDSMPPKT | INFINIPATH_E_SDROPPEDDATAPKT |
- INFINIPATH_E_SPIOARMLAUNCH | INFINIPATH_E_SUNEXPERRPKTNUM |
- INFINIPATH_E_SUNSUPVL | INFINIPATH_E_IBSTATUSCHANGED |
- INFINIPATH_E_INVALIDADDR | INFINIPATH_E_RESET |
- INFINIPATH_E_HARDWARE;
-
- infinipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK;
- infinipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK;
-}
-
-/* setup the MSI stuff again after a reset. I'd like to just call
- * pci_enable_msi() and request_irq() again, but when I do that,
- * the MSI enable bit doesn't get set in the command word, and
- * we switch to to a different interrupt vector, which is confusing,
- * so I instead just do it all inline. Perhaps somehow can tie this
- * into the PCIe hotplug support at some point
- * Note, because I'm doing it all here, I don't call pci_disable_msi()
- * or free_irq() at the start of ipath_setup_pe_reset().
- */
-static int ipath_reinit_msi(struct ipath_devdata *dd)
-{
- int pos;
- u16 control;
- int ret;
-
- if (!dd->ipath_msi_lo) {
- dev_info(&dd->pcidev->dev, "Can't restore MSI config, "
- "initial setup failed?\n");
- ret = 0;
- goto bail;
- }
-
- if (!(pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_MSI))) {
- ipath_dev_err(dd, "Can't find MSI capability, "
- "can't restore MSI settings\n");
- ret = 0;
- goto bail;
- }
- ipath_cdbg(VERBOSE, "Writing msi_lo 0x%x to config offset 0x%x\n",
- dd->ipath_msi_lo, pos + PCI_MSI_ADDRESS_LO);
- pci_write_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_LO,
- dd->ipath_msi_lo);
- ipath_cdbg(VERBOSE, "Writing msi_lo 0x%x to config offset 0x%x\n",
- dd->ipath_msi_hi, pos + PCI_MSI_ADDRESS_HI);
- pci_write_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_HI,
- dd->ipath_msi_hi);
- pci_read_config_word(dd->pcidev, pos + PCI_MSI_FLAGS, &control);
- if (!(control & PCI_MSI_FLAGS_ENABLE)) {
- ipath_cdbg(VERBOSE, "MSI control at off %x was %x, "
- "setting MSI enable (%x)\n", pos + PCI_MSI_FLAGS,
- control, control | PCI_MSI_FLAGS_ENABLE);
- control |= PCI_MSI_FLAGS_ENABLE;
- pci_write_config_word(dd->pcidev, pos + PCI_MSI_FLAGS,
- control);
- }
- /* now rewrite the data (vector) info */
- pci_write_config_word(dd->pcidev, pos +
- ((control & PCI_MSI_FLAGS_64BIT) ? 12 : 8),
- dd->ipath_msi_data);
- /* we restore the cachelinesize also, although it doesn't really
- * matter */
- pci_write_config_byte(dd->pcidev, PCI_CACHE_LINE_SIZE,
- dd->ipath_pci_cacheline);
- /* and now set the pci master bit again */
- pci_set_master(dd->pcidev);
- ret = 1;
-
-bail:
- return ret;
-}
-
-/* This routine sleeps, so it can only be called from user context, not
- * from interrupt context. If we need interrupt context, we can split
- * it into two routines.
-*/
-static int ipath_setup_pe_reset(struct ipath_devdata *dd)
-{
- u64 val;
- int i;
- int ret;
-
- /* Use ERROR so it shows up in logs, etc. */
- ipath_dev_err(dd, "Resetting PE-800 unit %u\n",
- dd->ipath_unit);
- /* keep chip from being accessed in a few places */
- dd->ipath_flags &= ~(IPATH_INITTED|IPATH_PRESENT);
- val = dd->ipath_control | INFINIPATH_C_RESET;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_control, val);
- mb();
-
- for (i = 1; i <= 5; i++) {
- int r;
- /* allow MBIST, etc. to complete; longer on each retry.
- * We sometimes get machine checks from bus timeout if no
- * response, so for now, make it *really* long.
- */
- msleep(1000 + (1 + i) * 2000);
- if ((r =
- pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_0,
- dd->ipath_pcibar0)))
- ipath_dev_err(dd, "rewrite of BAR0 failed: %d\n",
- r);
- if ((r =
- pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_1,
- dd->ipath_pcibar1)))
- ipath_dev_err(dd, "rewrite of BAR1 failed: %d\n",
- r);
- /* now re-enable memory access */
- if ((r = pci_enable_device(dd->pcidev)))
- ipath_dev_err(dd, "pci_enable_device failed after "
- "reset: %d\n", r);
- /* whether it worked or not, mark as present, again */
- dd->ipath_flags |= IPATH_PRESENT;
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_revision);
- if (val == dd->ipath_revision) {
- ipath_cdbg(VERBOSE, "Got matching revision "
- "register %llx on try %d\n",
- (unsigned long long) val, i);
- ret = ipath_reinit_msi(dd);
- goto bail;
- }
- /* Probably getting -1 back */
- ipath_dbg("Didn't get expected revision register, "
- "got %llx, try %d\n", (unsigned long long) val,
- i + 1);
- }
- ret = 0; /* failed */
-
-bail:
- return ret;
-}
-
-/**
- * ipath_pe_put_tid - write a TID in chip
- * @dd: the infinipath device
- * @tidptr: pointer to the expected TID (in chip) to udpate
- * @tidtype: 0 for eager, 1 for expected
- * @pa: physical address of in memory buffer; ipath_tidinvalid if freeing
- *
- * This exists as a separate routine to allow for special locking etc.
- * It's used for both the full cleanup on exit, as well as the normal
- * setup and teardown.
- */
-static void ipath_pe_put_tid(struct ipath_devdata *dd, u64 __iomem *tidptr,
- u32 type, unsigned long pa)
-{
- u32 __iomem *tidp32 = (u32 __iomem *)tidptr;
- unsigned long flags = 0; /* keep gcc quiet */
-
- if (pa != dd->ipath_tidinvalid) {
- if (pa & ((1U << 11) - 1)) {
- dev_info(&dd->pcidev->dev, "BUG: physaddr %lx "
- "not 4KB aligned!\n", pa);
- return;
- }
- pa >>= 11;
- /* paranoia check */
- if (pa & (7<<29))
- ipath_dev_err(dd,
- "BUG: Physical page address 0x%lx "
- "has bits set in 31-29\n", pa);
-
- if (type == 0)
- pa |= dd->ipath_tidtemplate;
- else /* for now, always full 4KB page */
- pa |= 2 << 29;
- }
-
- /* workaround chip bug 9437 by writing each TID twice
- * and holding a spinlock around the writes, so they don't
- * intermix with other TID (eager or expected) writes
- * Unfortunately, this call can be done from interrupt level
- * for the port 0 eager TIDs, so we have to use irqsave
- */
- spin_lock_irqsave(&dd->ipath_tid_lock, flags);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_scratch, 0xfeeddeaf);
- if (dd->ipath_kregbase)
- writel(pa, tidp32);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_scratch, 0xdeadbeef);
- mmiowb();
- spin_unlock_irqrestore(&dd->ipath_tid_lock, flags);
-}
-
-/**
- * ipath_pe_clear_tid - clear all TID entries for a port, expected and eager
- * @dd: the infinipath device
- * @port: the port
- *
- * clear all TID entries for a port, expected and eager.
- * Used from ipath_close(). On PE800, TIDs are only 32 bits,
- * not 64, but they are still on 64 bit boundaries, so tidbase
- * is declared as u64 * for the pointer math, even though we write 32 bits
- */
-static void ipath_pe_clear_tids(struct ipath_devdata *dd, unsigned port)
-{
- u64 __iomem *tidbase;
- unsigned long tidinv;
- int i;
-
- if (!dd->ipath_kregbase)
- return;
-
- ipath_cdbg(VERBOSE, "Invalidate TIDs for port %u\n", port);
-
- tidinv = dd->ipath_tidinvalid;
- tidbase = (u64 __iomem *)
- ((char __iomem *)(dd->ipath_kregbase) +
- dd->ipath_rcvtidbase +
- port * dd->ipath_rcvtidcnt * sizeof(*tidbase));
-
- for (i = 0; i < dd->ipath_rcvtidcnt; i++)
- ipath_pe_put_tid(dd, &tidbase[i], 0, tidinv);
-
- tidbase = (u64 __iomem *)
- ((char __iomem *)(dd->ipath_kregbase) +
- dd->ipath_rcvegrbase +
- port * dd->ipath_rcvegrcnt * sizeof(*tidbase));
-
- for (i = 0; i < dd->ipath_rcvegrcnt; i++)
- ipath_pe_put_tid(dd, &tidbase[i], 1, tidinv);
-}
-
-/**
- * ipath_pe_tidtemplate - setup constants for TID updates
- * @dd: the infinipath device
- *
- * We setup stuff that we use a lot, to avoid calculating each time
- */
-static void ipath_pe_tidtemplate(struct ipath_devdata *dd)
-{
- u32 egrsize = dd->ipath_rcvegrbufsize;
-
- /* For now, we always allocate 4KB buffers (at init) so we can
- * receive max size packets. We may want a module parameter to
- * specify 2KB or 4KB and/or make be per port instead of per device
- * for those who want to reduce memory footprint. Note that the
- * ipath_rcvhdrentsize size must be large enough to hold the largest
- * IB header (currently 96 bytes) that we expect to handle (plus of
- * course the 2 dwords of RHF).
- */
- if (egrsize == 2048)
- dd->ipath_tidtemplate = 1U << 29;
- else if (egrsize == 4096)
- dd->ipath_tidtemplate = 2U << 29;
- else {
- egrsize = 4096;
- dev_info(&dd->pcidev->dev, "BUG: unsupported egrbufsize "
- "%u, using %u\n", dd->ipath_rcvegrbufsize,
- egrsize);
- dd->ipath_tidtemplate = 2U << 29;
- }
- dd->ipath_tidinvalid = 0;
-}
-
-static int ipath_pe_early_init(struct ipath_devdata *dd)
-{
- dd->ipath_flags |= IPATH_4BYTE_TID;
-
- /*
- * For openib, we need to be able to handle an IB header of 96 bytes
- * or 24 dwords. HT-400 has arbitrary sized receive buffers, so we
- * made them the same size as the PIO buffers. The PE-800 does not
- * handle arbitrary size buffers, so we need the header large enough
- * to handle largest IB header, but still have room for a 2KB MTU
- * standard IB packet.
- */
- dd->ipath_rcvhdrentsize = 24;
- dd->ipath_rcvhdrsize = IPATH_DFLT_RCVHDRSIZE;
-
- /* For HT-400, we allocate a somewhat overly large eager buffer,
- * such that we can guarantee that we can receive the largest packet
- * that we can send out. To truly support a 4KB MTU, we need to
- * bump this to a larger value. We'll do this when I get around to
- * testing 4KB sends on the PE-800, which I have not yet done.
- */
- dd->ipath_rcvegrbufsize = 2048;
- /*
- * the min() check here is currently a nop, but it may not always
- * be, depending on just how we do ipath_rcvegrbufsize
- */
- dd->ipath_ibmaxlen = min(dd->ipath_piosize2k,
- dd->ipath_rcvegrbufsize +
- (dd->ipath_rcvhdrentsize << 2));
- dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen;
-
- /*
- * For PE-800, we can request a receive interrupt for 1 or
- * more packets from current offset. For now, we set this
- * up for a single packet, to match the HT-400 behavior.
- */
- dd->ipath_rhdrhead_intr_off = 1ULL<<32;
-
- ipath_get_eeprom_info(dd);
-
- return 0;
-}
-
-int __attribute__((weak)) ipath_unordered_wc(void)
-{
- return 0;
-}
-
-/**
- * ipath_init_pe_get_base_info - set chip-specific flags for user code
- * @dd: the infinipath device
- * @kbase: ipath_base_info pointer
- *
- * We set the PCIE flag because the lower bandwidth on PCIe vs
- * HyperTransport can affect some user packet algorithims.
- */
-static int ipath_pe_get_base_info(struct ipath_portdata *pd, void *kbase)
-{
- struct ipath_base_info *kinfo = kbase;
-
- if (ipath_unordered_wc()) {
- kinfo->spi_runtime_flags |= IPATH_RUNTIME_FORCE_WC_ORDER;
- ipath_cdbg(PROC, "Intel processor, forcing WC order\n");
- }
- else
- ipath_cdbg(PROC, "Not Intel processor, WC ordered\n");
-
- kinfo->spi_runtime_flags |= IPATH_RUNTIME_PCIE;
-
- return 0;
-}
-
-/**
- * ipath_init_pe800_funcs - set up the chip-specific function pointers
- * @dd: the infinipath device
- *
- * This is global, and is called directly at init to set up the
- * chip-specific function pointers for later use.
- */
-void ipath_init_pe800_funcs(struct ipath_devdata *dd)
-{
- dd->ipath_f_intrsetup = ipath_pe_intconfig;
- dd->ipath_f_bus = ipath_setup_pe_config;
- dd->ipath_f_reset = ipath_setup_pe_reset;
- dd->ipath_f_get_boardname = ipath_pe_boardname;
- dd->ipath_f_init_hwerrors = ipath_pe_init_hwerrors;
- dd->ipath_f_early_init = ipath_pe_early_init;
- dd->ipath_f_handle_hwerrors = ipath_pe_handle_hwerrors;
- dd->ipath_f_quiet_serdes = ipath_pe_quiet_serdes;
- dd->ipath_f_bringup_serdes = ipath_pe_bringup_serdes;
- dd->ipath_f_clear_tids = ipath_pe_clear_tids;
- dd->ipath_f_put_tid = ipath_pe_put_tid;
- dd->ipath_f_cleanup = ipath_setup_pe_cleanup;
- dd->ipath_f_setextled = ipath_setup_pe_setextled;
- dd->ipath_f_get_base_info = ipath_pe_get_base_info;
-
- /* initialize chip-specific variables */
- dd->ipath_f_tidtemplate = ipath_pe_tidtemplate;
-
- /*
- * setup the register offsets, since they are different for each
- * chip
- */
- dd->ipath_kregs = &ipath_pe_kregs;
- dd->ipath_cregs = &ipath_pe_cregs;
-
- ipath_init_pe_variables();
-}
-
/*
* This file should only be included by kernel source, and by the diags. It
- * defines the registers, and their contents, for the InfiniPath HT-400
- * chip.
+ * defines the registers, and their contents, for InfiniPath chips.
*/
/*
#define INFINIPATH_RT_ADDR_MASK 0xFFFFFFFFFFULL /* 40 bits valid */
-/* TID entries (memory), HT400-only */
+/* TID entries (memory), HT-only */
#define INFINIPATH_RT_VALID 0x8000000000000000ULL
#define INFINIPATH_RT_ADDR_SHIFT 0
#define INFINIPATH_RT_BUFSIZE_MASK 0x3FFF
projects / powerpc.git / commitdiff