--- /dev/null
- * piix_sata_prereset - prereset for SATA host controller
+/*
+ * ata_piix.c - Intel PATA/SATA controllers
+ *
+ * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Please ALWAYS copy linux-ide@vger.kernel.org
+ * on emails.
+ *
+ *
+ * Copyright 2003-2005 Red Hat Inc
+ * Copyright 2003-2005 Jeff Garzik
+ *
+ *
+ * Copyright header from piix.c:
+ *
+ * Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
+ * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING. If not, write to
+ * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *
+ * libata documentation is available via 'make {ps|pdf}docs',
+ * as Documentation/DocBook/libata.*
+ *
+ * Hardware documentation available at http://developer.intel.com/
+ *
+ * Documentation
+ * Publically available from Intel web site. Errata documentation
+ * is also publically available. As an aide to anyone hacking on this
+ * driver the list of errata that are relevant is below.going back to
+ * PIIX4. Older device documentation is now a bit tricky to find.
+ *
+ * The chipsets all follow very much the same design. The orginal Triton
+ * series chipsets do _not_ support independant device timings, but this
+ * is fixed in Triton II. With the odd mobile exception the chips then
+ * change little except in gaining more modes until SATA arrives. This
+ * driver supports only the chips with independant timing (that is those
+ * with SITRE and the 0x44 timing register). See pata_oldpiix and pata_mpiix
+ * for the early chip drivers.
+ *
+ * Errata of note:
+ *
+ * Unfixable
+ * PIIX4 errata #9 - Only on ultra obscure hw
+ * ICH3 errata #13 - Not observed to affect real hw
+ * by Intel
+ *
+ * Things we must deal with
+ * PIIX4 errata #10 - BM IDE hang with non UDMA
+ * (must stop/start dma to recover)
+ * 440MX errata #15 - As PIIX4 errata #10
+ * PIIX4 errata #15 - Must not read control registers
+ * during a PIO transfer
+ * 440MX errata #13 - As PIIX4 errata #15
+ * ICH2 errata #21 - DMA mode 0 doesn't work right
+ * ICH0/1 errata #55 - As ICH2 errata #21
+ * ICH2 spec c #9 - Extra operations needed to handle
+ * drive hotswap [NOT YET SUPPORTED]
+ * ICH2 spec c #20 - IDE PRD must not cross a 64K boundary
+ * and must be dword aligned
+ * ICH2 spec c #24 - UDMA mode 4,5 t85/86 should be 6ns not 3.3
+ *
+ * Should have been BIOS fixed:
+ * 450NX: errata #19 - DMA hangs on old 450NX
+ * 450NX: errata #20 - DMA hangs on old 450NX
+ * 450NX: errata #25 - Corruption with DMA on old 450NX
+ * ICH3 errata #15 - IDE deadlock under high load
+ * (BIOS must set dev 31 fn 0 bit 23)
+ * ICH3 errata #18 - Don't use native mode
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "ata_piix"
+#define DRV_VERSION "2.00"
+
+enum {
+ PIIX_IOCFG = 0x54, /* IDE I/O configuration register */
+ ICH5_PMR = 0x90, /* port mapping register */
+ ICH5_PCS = 0x92, /* port control and status */
+ PIIX_SCC = 0x0A, /* sub-class code register */
+
+ PIIX_FLAG_IGNORE_PCS = (1 << 25), /* ignore PCS present bits */
+ PIIX_FLAG_SCR = (1 << 26), /* SCR available */
+ PIIX_FLAG_AHCI = (1 << 27), /* AHCI possible */
+ PIIX_FLAG_CHECKINTR = (1 << 28), /* make sure PCI INTx enabled */
+
+ /* combined mode. if set, PATA is channel 0.
+ * if clear, PATA is channel 1.
+ */
+ PIIX_PORT_ENABLED = (1 << 0),
+ PIIX_PORT_PRESENT = (1 << 4),
+
+ PIIX_80C_PRI = (1 << 5) | (1 << 4),
+ PIIX_80C_SEC = (1 << 7) | (1 << 6),
+
+ /* controller IDs */
+ piix4_pata = 0,
+ ich5_pata = 1,
+ ich5_sata = 2,
+ esb_sata = 3,
+ ich6_sata = 4,
+ ich6_sata_ahci = 5,
+ ich6m_sata_ahci = 6,
+ ich8_sata_ahci = 7,
+
+ /* constants for mapping table */
+ P0 = 0, /* port 0 */
+ P1 = 1, /* port 1 */
+ P2 = 2, /* port 2 */
+ P3 = 3, /* port 3 */
+ IDE = -1, /* IDE */
+ NA = -2, /* not avaliable */
+ RV = -3, /* reserved */
+
+ PIIX_AHCI_DEVICE = 6,
+};
+
+struct piix_map_db {
+ const u32 mask;
+ const u16 port_enable;
+ const int present_shift;
+ const int map[][4];
+};
+
+struct piix_host_priv {
+ const int *map;
+ const struct piix_map_db *map_db;
+};
+
+static int piix_init_one (struct pci_dev *pdev,
+ const struct pci_device_id *ent);
+static void piix_host_stop(struct ata_host_set *host_set);
+static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev);
+static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev);
+static void piix_pata_error_handler(struct ata_port *ap);
+static void piix_sata_error_handler(struct ata_port *ap);
+
+static unsigned int in_module_init = 1;
+
+static const struct pci_device_id piix_pci_tbl[] = {
+#ifdef ATA_ENABLE_PATA
+ { 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix4_pata },
+ { 0x8086, 0x24db, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata },
+ { 0x8086, 0x25a2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata },
+ { 0x8086, 0x27df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata },
+#endif
+
+ /* NOTE: The following PCI ids must be kept in sync with the
+ * list in drivers/pci/quirks.c.
+ */
+
+ /* 82801EB (ICH5) */
+ { 0x8086, 0x24d1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
+ /* 82801EB (ICH5) */
+ { 0x8086, 0x24df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
+ /* 6300ESB (ICH5 variant with broken PCS present bits) */
+ { 0x8086, 0x25a3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb_sata },
+ /* 6300ESB pretending RAID */
+ { 0x8086, 0x25b0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb_sata },
+ /* 82801FB/FW (ICH6/ICH6W) */
+ { 0x8086, 0x2651, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
+ /* 82801FR/FRW (ICH6R/ICH6RW) */
+ { 0x8086, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ /* 82801FBM ICH6M (ICH6R with only port 0 and 2 implemented) */
+ { 0x8086, 0x2653, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci },
+ /* 82801GB/GR/GH (ICH7, identical to ICH6) */
+ { 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ /* 2801GBM/GHM (ICH7M, identical to ICH6M) */
+ { 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci },
+ /* Enterprise Southbridge 2 (where's the datasheet?) */
+ { 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ /* SATA Controller 1 IDE (ICH8, no datasheet yet) */
+ { 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller 2 IDE (ICH8, ditto) */
+ { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* Mobile SATA Controller IDE (ICH8M, ditto) */
+ { 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+
+ { } /* terminate list */
+};
+
+static struct pci_driver piix_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = piix_pci_tbl,
+ .probe = piix_init_one,
+ .remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
+};
+
+static struct scsi_host_template piix_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
+ .bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
+};
+
+static const struct ata_port_operations piix_pata_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = piix_set_piomode,
+ .set_dmamode = piix_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_pio_data_xfer,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = piix_pata_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = piix_host_stop,
+};
+
+static const struct ata_port_operations piix_sata_ops = {
+ .port_disable = ata_port_disable,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_pio_data_xfer,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = piix_sata_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = piix_host_stop,
+};
+
+static const struct piix_map_db ich5_map_db = {
+ .mask = 0x7,
+ .port_enable = 0x3,
+ .present_shift = 4,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, NA, P1, NA }, /* 000b */
+ { P1, NA, P0, NA }, /* 001b */
+ { RV, RV, RV, RV },
+ { RV, RV, RV, RV },
+ { P0, P1, IDE, IDE }, /* 100b */
+ { P1, P0, IDE, IDE }, /* 101b */
+ { IDE, IDE, P0, P1 }, /* 110b */
+ { IDE, IDE, P1, P0 }, /* 111b */
+ },
+};
+
+static const struct piix_map_db ich6_map_db = {
+ .mask = 0x3,
+ .port_enable = 0xf,
+ .present_shift = 4,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, P2, P1, P3 }, /* 00b */
+ { IDE, IDE, P1, P3 }, /* 01b */
+ { P0, P2, IDE, IDE }, /* 10b */
+ { RV, RV, RV, RV },
+ },
+};
+
+static const struct piix_map_db ich6m_map_db = {
+ .mask = 0x3,
+ .port_enable = 0x5,
+ .present_shift = 4,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, P2, RV, RV }, /* 00b */
+ { RV, RV, RV, RV },
+ { P0, P2, IDE, IDE }, /* 10b */
+ { RV, RV, RV, RV },
+ },
+};
+
+static const struct piix_map_db ich8_map_db = {
+ .mask = 0x3,
+ .port_enable = 0x3,
+ .present_shift = 8,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, NA, P1, NA }, /* 00b (hardwired) */
+ { RV, RV, RV, RV },
+ { RV, RV, RV, RV }, /* 10b (never) */
+ { RV, RV, RV, RV },
+ },
+};
+
+static const struct piix_map_db *piix_map_db_table[] = {
+ [ich5_sata] = &ich5_map_db,
+ [esb_sata] = &ich5_map_db,
+ [ich6_sata] = &ich6_map_db,
+ [ich6_sata_ahci] = &ich6_map_db,
+ [ich6m_sata_ahci] = &ich6m_map_db,
+ [ich8_sata_ahci] = &ich8_map_db,
+};
+
+static struct ata_port_info piix_port_info[] = {
+ /* piix4_pata */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = 0x1f, /* pio0-4 */
+#if 0
+ .mwdma_mask = 0x06, /* mwdma1-2 */
+#else
+ .mwdma_mask = 0x00, /* mwdma broken */
+#endif
+ .udma_mask = ATA_UDMA_MASK_40C,
+ .port_ops = &piix_pata_ops,
+ },
+
+ /* ich5_pata */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR,
+ .pio_mask = 0x1f, /* pio0-4 */
+#if 0
+ .mwdma_mask = 0x06, /* mwdma1-2 */
+#else
+ .mwdma_mask = 0x00, /* mwdma broken */
+#endif
+ .udma_mask = 0x3f, /* udma0-5 */
+ .port_ops = &piix_pata_ops,
+ },
+
+ /* ich5_sata */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* i6300esb_sata */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SATA |
+ PIIX_FLAG_CHECKINTR | PIIX_FLAG_IGNORE_PCS,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* ich6_sata */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SATA |
+ PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* ich6_sata_ahci */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SATA |
+ PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* ich6m_sata_ahci */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SATA |
+ PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* ich8_sata_ahci */
+ {
+ .sht = &piix_sht,
+ .host_flags = ATA_FLAG_SATA |
+ PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+};
+
+static struct pci_bits piix_enable_bits[] = {
+ { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */
+ { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */
+};
+
+MODULE_AUTHOR("Andre Hedrick, Alan Cox, Andrzej Krzysztofowicz, Jeff Garzik");
+MODULE_DESCRIPTION("SCSI low-level driver for Intel PIIX/ICH ATA controllers");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
+/**
+ * piix_pata_cbl_detect - Probe host controller cable detect info
+ * @ap: Port for which cable detect info is desired
+ *
+ * Read 80c cable indicator from ATA PCI device's PCI config
+ * register. This register is normally set by firmware (BIOS).
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+static void piix_pata_cbl_detect(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+ u8 tmp, mask;
+
+ /* no 80c support in host controller? */
+ if ((ap->udma_mask & ~ATA_UDMA_MASK_40C) == 0)
+ goto cbl40;
+
+ /* check BIOS cable detect results */
+ mask = ap->port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
+ pci_read_config_byte(pdev, PIIX_IOCFG, &tmp);
+ if ((tmp & mask) == 0)
+ goto cbl40;
+
+ ap->cbl = ATA_CBL_PATA80;
+ return;
+
+cbl40:
+ ap->cbl = ATA_CBL_PATA40;
+ ap->udma_mask &= ATA_UDMA_MASK_40C;
+}
+
+/**
+ * piix_pata_prereset - prereset for PATA host controller
+ * @ap: Target port
+ *
+ * Prereset including cable detection.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+static int piix_pata_prereset(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+
+ if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no])) {
+ ata_port_printk(ap, KERN_INFO, "port disabled. ignoring.\n");
+ ap->eh_context.i.action &= ~ATA_EH_RESET_MASK;
+ return 0;
+ }
+
+ piix_pata_cbl_detect(ap);
+
+ return ata_std_prereset(ap);
+}
+
+static void piix_pata_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, piix_pata_prereset, ata_std_softreset, NULL,
+ ata_std_postreset);
+}
+
+/**
- * Reads and configures SATA PCI device's PCI config register
- * Port Configuration and Status (PCS) to determine port and
- * device availability. Return -ENODEV to skip reset if no
- * device is present.
++ * piix_sata_present_mask - determine present mask for SATA host controller
+ * @ap: Target port
+ *
- * 0 if device is present, -ENODEV otherwise.
++ * Reads SATA PCI device's PCI config register Port Configuration
++ * and Status (PCS) to determine port and device availability.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ *
+ * RETURNS:
- static int piix_sata_prereset(struct ata_port *ap)
++ * determined present_mask
+ */
- unsigned int present = 0;
++static unsigned int piix_sata_present_mask(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+ struct piix_host_priv *hpriv = ap->host_set->private_data;
+ const unsigned int *map = hpriv->map;
+ int base = 2 * ap->port_no;
- present = 1;
++ unsigned int present_mask = 0;
+ int port, i;
+ u16 pcs;
+
+ pci_read_config_word(pdev, ICH5_PCS, &pcs);
+ DPRINTK("ata%u: ENTER, pcs=0x%x base=%d\n", ap->id, pcs, base);
+
+ for (i = 0; i < 2; i++) {
+ port = map[base + i];
+ if (port < 0)
+ continue;
+ if ((ap->flags & PIIX_FLAG_IGNORE_PCS) ||
+ (pcs & 1 << (hpriv->map_db->present_shift + port)))
- DPRINTK("ata%u: LEAVE, pcs=0x%x present=0x%x\n",
- ap->id, pcs, present);
++ present_mask |= 1 << i;
+ }
+
- if (!present) {
- ata_port_printk(ap, KERN_INFO, "SATA port has no device.\n");
- ap->eh_context.i.action &= ~ATA_EH_RESET_MASK;
- return 0;
++ DPRINTK("ata%u: LEAVE, pcs=0x%x present_mask=0x%x\n",
++ ap->id, pcs, present_mask);
+
- return ata_std_prereset(ap);
++ return present_mask;
++}
++
++/**
++ * piix_sata_softreset - reset SATA host port via ATA SRST
++ * @ap: port to reset
++ * @classes: resulting classes of attached devices
++ *
++ * Reset SATA host port via ATA SRST. On controllers with
++ * reliable PCS present bits, the bits are used to determine
++ * device presence.
++ *
++ * LOCKING:
++ * Kernel thread context (may sleep)
++ *
++ * RETURNS:
++ * 0 on success, -errno otherwise.
++ */
++static int piix_sata_softreset(struct ata_port *ap, unsigned int *classes)
++{
++ unsigned int present_mask;
++ int i, rc;
++
++ present_mask = piix_sata_present_mask(ap);
++
++ rc = ata_std_softreset(ap, classes);
++ if (rc)
++ return rc;
++
++ for (i = 0; i < ATA_MAX_DEVICES; i++) {
++ if (!(present_mask & (1 << i)))
++ classes[i] = ATA_DEV_NONE;
+ }
+
- ata_bmdma_drive_eh(ap, piix_sata_prereset, ata_std_softreset, NULL,
++ return 0;
+}
+
+static void piix_sata_error_handler(struct ata_port *ap)
+{
++ ata_bmdma_drive_eh(ap, ata_std_prereset, piix_sata_softreset, NULL,
+ ata_std_postreset);
+}
+
+/**
+ * piix_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ *
+ * Set PIO mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int pio = adev->pio_mode - XFER_PIO_0;
+ struct pci_dev *dev = to_pci_dev(ap->host_set->dev);
+ unsigned int is_slave = (adev->devno != 0);
+ unsigned int master_port= ap->port_no ? 0x42 : 0x40;
+ unsigned int slave_port = 0x44;
+ u16 master_data;
+ u8 slave_data;
+
+ static const /* ISP RTC */
+ u8 timings[][2] = { { 0, 0 },
+ { 0, 0 },
+ { 1, 0 },
+ { 2, 1 },
+ { 2, 3 }, };
+
+ pci_read_config_word(dev, master_port, &master_data);
+ if (is_slave) {
+ master_data |= 0x4000;
+ /* enable PPE, IE and TIME */
+ master_data |= 0x0070;
+ pci_read_config_byte(dev, slave_port, &slave_data);
+ slave_data &= (ap->port_no ? 0x0f : 0xf0);
+ slave_data |=
+ (timings[pio][0] << 2) |
+ (timings[pio][1] << (ap->port_no ? 4 : 0));
+ } else {
+ master_data &= 0xccf8;
+ /* enable PPE, IE and TIME */
+ master_data |= 0x0007;
+ master_data |=
+ (timings[pio][0] << 12) |
+ (timings[pio][1] << 8);
+ }
+ pci_write_config_word(dev, master_port, master_data);
+ if (is_slave)
+ pci_write_config_byte(dev, slave_port, slave_data);
+}
+
+/**
+ * piix_set_dmamode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ * @udma: udma mode, 0 - 6
+ *
+ * Set UDMA mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int udma = adev->dma_mode; /* FIXME: MWDMA too */
+ struct pci_dev *dev = to_pci_dev(ap->host_set->dev);
+ u8 maslave = ap->port_no ? 0x42 : 0x40;
+ u8 speed = udma;
+ unsigned int drive_dn = (ap->port_no ? 2 : 0) + adev->devno;
+ int a_speed = 3 << (drive_dn * 4);
+ int u_flag = 1 << drive_dn;
+ int v_flag = 0x01 << drive_dn;
+ int w_flag = 0x10 << drive_dn;
+ int u_speed = 0;
+ int sitre;
+ u16 reg4042, reg4a;
+ u8 reg48, reg54, reg55;
+
+ pci_read_config_word(dev, maslave, ®4042);
+ DPRINTK("reg4042 = 0x%04x\n", reg4042);
+ sitre = (reg4042 & 0x4000) ? 1 : 0;
+ pci_read_config_byte(dev, 0x48, ®48);
+ pci_read_config_word(dev, 0x4a, ®4a);
+ pci_read_config_byte(dev, 0x54, ®54);
+ pci_read_config_byte(dev, 0x55, ®55);
+
+ switch(speed) {
+ case XFER_UDMA_4:
+ case XFER_UDMA_2: u_speed = 2 << (drive_dn * 4); break;
+ case XFER_UDMA_6:
+ case XFER_UDMA_5:
+ case XFER_UDMA_3:
+ case XFER_UDMA_1: u_speed = 1 << (drive_dn * 4); break;
+ case XFER_UDMA_0: u_speed = 0 << (drive_dn * 4); break;
+ case XFER_MW_DMA_2:
+ case XFER_MW_DMA_1: break;
+ default:
+ BUG();
+ return;
+ }
+
+ if (speed >= XFER_UDMA_0) {
+ if (!(reg48 & u_flag))
+ pci_write_config_byte(dev, 0x48, reg48 | u_flag);
+ if (speed == XFER_UDMA_5) {
+ pci_write_config_byte(dev, 0x55, (u8) reg55|w_flag);
+ } else {
+ pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
+ }
+ if ((reg4a & a_speed) != u_speed)
+ pci_write_config_word(dev, 0x4a, (reg4a & ~a_speed) | u_speed);
+ if (speed > XFER_UDMA_2) {
+ if (!(reg54 & v_flag))
+ pci_write_config_byte(dev, 0x54, reg54 | v_flag);
+ } else
+ pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
+ } else {
+ if (reg48 & u_flag)
+ pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
+ if (reg4a & a_speed)
+ pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
+ if (reg54 & v_flag)
+ pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
+ if (reg55 & w_flag)
+ pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
+ }
+}
+
+#define AHCI_PCI_BAR 5
+#define AHCI_GLOBAL_CTL 0x04
+#define AHCI_ENABLE (1 << 31)
+static int piix_disable_ahci(struct pci_dev *pdev)
+{
+ void __iomem *mmio;
+ u32 tmp;
+ int rc = 0;
+
+ /* BUG: pci_enable_device has not yet been called. This
+ * works because this device is usually set up by BIOS.
+ */
+
+ if (!pci_resource_start(pdev, AHCI_PCI_BAR) ||
+ !pci_resource_len(pdev, AHCI_PCI_BAR))
+ return 0;
+
+ mmio = pci_iomap(pdev, AHCI_PCI_BAR, 64);
+ if (!mmio)
+ return -ENOMEM;
+
+ tmp = readl(mmio + AHCI_GLOBAL_CTL);
+ if (tmp & AHCI_ENABLE) {
+ tmp &= ~AHCI_ENABLE;
+ writel(tmp, mmio + AHCI_GLOBAL_CTL);
+
+ tmp = readl(mmio + AHCI_GLOBAL_CTL);
+ if (tmp & AHCI_ENABLE)
+ rc = -EIO;
+ }
+
+ pci_iounmap(pdev, mmio);
+ return rc;
+}
+
+/**
+ * piix_check_450nx_errata - Check for problem 450NX setup
+ * @ata_dev: the PCI device to check
+ *
+ * Check for the present of 450NX errata #19 and errata #25. If
+ * they are found return an error code so we can turn off DMA
+ */
+
+static int __devinit piix_check_450nx_errata(struct pci_dev *ata_dev)
+{
+ struct pci_dev *pdev = NULL;
+ u16 cfg;
+ u8 rev;
+ int no_piix_dma = 0;
+
+ while((pdev = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev)) != NULL)
+ {
+ /* Look for 450NX PXB. Check for problem configurations
+ A PCI quirk checks bit 6 already */
+ pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+ pci_read_config_word(pdev, 0x41, &cfg);
+ /* Only on the original revision: IDE DMA can hang */
+ if (rev == 0x00)
+ no_piix_dma = 1;
+ /* On all revisions below 5 PXB bus lock must be disabled for IDE */
+ else if (cfg & (1<<14) && rev < 5)
+ no_piix_dma = 2;
+ }
+ if (no_piix_dma)
+ dev_printk(KERN_WARNING, &ata_dev->dev, "450NX errata present, disabling IDE DMA.\n");
+ if (no_piix_dma == 2)
+ dev_printk(KERN_WARNING, &ata_dev->dev, "A BIOS update may resolve this.\n");
+ return no_piix_dma;
+}
+
+static void __devinit piix_init_pcs(struct pci_dev *pdev,
+ const struct piix_map_db *map_db)
+{
+ u16 pcs, new_pcs;
+
+ pci_read_config_word(pdev, ICH5_PCS, &pcs);
+
+ new_pcs = pcs | map_db->port_enable;
+
+ if (new_pcs != pcs) {
+ DPRINTK("updating PCS from 0x%x to 0x%x\n", pcs, new_pcs);
+ pci_write_config_word(pdev, ICH5_PCS, new_pcs);
+ msleep(150);
+ }
+}
+
+static void __devinit piix_init_sata_map(struct pci_dev *pdev,
+ struct ata_port_info *pinfo,
+ const struct piix_map_db *map_db)
+{
+ struct piix_host_priv *hpriv = pinfo[0].private_data;
+ const unsigned int *map;
+ int i, invalid_map = 0;
+ u8 map_value;
+
+ pci_read_config_byte(pdev, ICH5_PMR, &map_value);
+
+ map = map_db->map[map_value & map_db->mask];
+
+ dev_printk(KERN_INFO, &pdev->dev, "MAP [");
+ for (i = 0; i < 4; i++) {
+ switch (map[i]) {
+ case RV:
+ invalid_map = 1;
+ printk(" XX");
+ break;
+
+ case NA:
+ printk(" --");
+ break;
+
+ case IDE:
+ WARN_ON((i & 1) || map[i + 1] != IDE);
+ pinfo[i / 2] = piix_port_info[ich5_pata];
+ pinfo[i / 2].private_data = hpriv;
+ i++;
+ printk(" IDE IDE");
+ break;
+
+ default:
+ printk(" P%d", map[i]);
+ if (i & 1)
+ pinfo[i / 2].host_flags |= ATA_FLAG_SLAVE_POSS;
+ break;
+ }
+ }
+ printk(" ]\n");
+
+ if (invalid_map)
+ dev_printk(KERN_ERR, &pdev->dev,
+ "invalid MAP value %u\n", map_value);
+
+ hpriv->map = map;
+ hpriv->map_db = map_db;
+}
+
+/**
+ * piix_init_one - Register PIIX ATA PCI device with kernel services
+ * @pdev: PCI device to register
+ * @ent: Entry in piix_pci_tbl matching with @pdev
+ *
+ * Called from kernel PCI layer. We probe for combined mode (sigh),
+ * and then hand over control to libata, for it to do the rest.
+ *
+ * LOCKING:
+ * Inherited from PCI layer (may sleep).
+ *
+ * RETURNS:
+ * Zero on success, or -ERRNO value.
+ */
+
+static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ static int printed_version;
+ struct ata_port_info port_info[2];
+ struct ata_port_info *ppinfo[2] = { &port_info[0], &port_info[1] };
+ struct piix_host_priv *hpriv;
+ unsigned long host_flags;
+
+ if (!printed_version++)
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "version " DRV_VERSION "\n");
+
+ /* no hotplugging support (FIXME) */
+ if (!in_module_init)
+ return -ENODEV;
+
+ hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL);
+ if (!hpriv)
+ return -ENOMEM;
+
+ port_info[0] = piix_port_info[ent->driver_data];
+ port_info[1] = piix_port_info[ent->driver_data];
+ port_info[0].private_data = hpriv;
+ port_info[1].private_data = hpriv;
+
+ host_flags = port_info[0].host_flags;
+
+ if (host_flags & PIIX_FLAG_AHCI) {
+ u8 tmp;
+ pci_read_config_byte(pdev, PIIX_SCC, &tmp);
+ if (tmp == PIIX_AHCI_DEVICE) {
+ int rc = piix_disable_ahci(pdev);
+ if (rc)
+ return rc;
+ }
+ }
+
+ /* Initialize SATA map */
+ if (host_flags & ATA_FLAG_SATA) {
+ piix_init_sata_map(pdev, port_info,
+ piix_map_db_table[ent->driver_data]);
+ piix_init_pcs(pdev, piix_map_db_table[ent->driver_data]);
+ }
+
+ /* On ICH5, some BIOSen disable the interrupt using the
+ * PCI_COMMAND_INTX_DISABLE bit added in PCI 2.3.
+ * On ICH6, this bit has the same effect, but only when
+ * MSI is disabled (and it is disabled, as we don't use
+ * message-signalled interrupts currently).
+ */
+ if (host_flags & PIIX_FLAG_CHECKINTR)
+ pci_intx(pdev, 1);
+
+ if (piix_check_450nx_errata(pdev)) {
+ /* This writes into the master table but it does not
+ really matter for this errata as we will apply it to
+ all the PIIX devices on the board */
+ port_info[0].mwdma_mask = 0;
+ port_info[0].udma_mask = 0;
+ port_info[1].mwdma_mask = 0;
+ port_info[1].udma_mask = 0;
+ }
+ return ata_pci_init_one(pdev, ppinfo, 2);
+}
+
+static void piix_host_stop(struct ata_host_set *host_set)
+{
+ struct piix_host_priv *hpriv = host_set->private_data;
+
+ ata_host_stop(host_set);
+
+ kfree(hpriv);
+}
+
+static int __init piix_init(void)
+{
+ int rc;
+
+ DPRINTK("pci_register_driver\n");
+ rc = pci_register_driver(&piix_pci_driver);
+ if (rc)
+ return rc;
+
+ in_module_init = 0;
+
+ DPRINTK("done\n");
+ return 0;
+}
+
+static void __exit piix_exit(void)
+{
+ pci_unregister_driver(&piix_pci_driver);
+}
+
+module_init(piix_init);
+module_exit(piix_exit);
+
projects / powerpc.git / commitdiff