$Conf{DfPath} = '/bin/df';
#
-# Command to run df. Several variables are substituted at run-time:
+# Command to run df. The following variables are substituted at run-time:
#
# $dfPath path to df ($Conf{DfPath})
# $topDir top-level BackupPC data directory
$Conf{SmbShareUserName} = '';
#
-# Smbclient share password. This is passed to smbclient via the PASSWD
+# Smbclient share password. This is passed to smbclient via its PASSWD
# environment variable. There are several ways you can tell BackupPC
# the smb share password. In each case you should be very careful about
# security. If you put the password here, make sure that this file is
# time taken for the backup, plus the granularity of $Conf{WakeupSchedule}
# will make the actual backup interval a bit longer.
#
+# There are two special values for $Conf{FullPeriod}:
+#
+# -1 Don't do any regular backups on this machine. Manually
+# requested backups (via the CGI interface) will still occur.
+#
+# -2 Don't do any backups on this machine. Manually requested
+# backups (via the CGI interface) will be ignored.
+#
+# These special settings are useful for a client that is no longer
+# being backed up (eg: a retired machine), but you wish to keep the
+# last backups available for browsing or restoring to other machines.
+#
+# Also, you might create a virtual client (by setting $Conf{ClientNameAlias})
+# for restoring to a DVD or permanent media and you would set
+# $Conf{FullPeriod} to -2 so that it is never backed up.
+#
$Conf{FullPeriod} = 6.97;
#
# $Conf{BackupFilesExclude} = {
# 'c' => ['/temp', '/winnt/tmp'], # these are for 'c' share
# 'd' => ['/junk', '/dont_back_this_up'], # these are for 'd' share
-# }
+# };
#
$Conf{BackupFilesExclude} = undef;
# - 'tar': backup and restore via tar, tar over ssh, rsh or nfs.
# Good choice for linux/unix.
#
-# A future version should support 'rsync' as a transport method for
-# more efficient backup of linux/unix machines (and perhaps WinXX??).
-#
$Conf{XferMethod} = 'smb';
#
# Commands to run smbclient for a full dump, incremental dump or a restore.
# This setting only matters if $Conf{XferMethod} = 'smb'.
#
-# Several variables are substituted at run-time:
+# The following variables are substituted at run-time:
#
# $smbClientPath same as $Conf{SmbClientPath}
# $host host to backup/restore
# are sufficient to read all the files you want to backup. Also, you
# will probably want to add "/proc" to $Conf{BackupFilesExclude}.
#
-# Several variables are substituted at run-time. The following variables
-# are substituted at run-time:
+# The following variables are substituted at run-time:
#
# $host host name
# $hostIP host's IP address
#
# This setting only matters if $Conf{XferMethod} = 'rsync'.
#
-$Conf{RsyncClientCmd} = '$sshPath -l root $host $rsyncPath $argList';
+$Conf{RsyncClientCmd} = '$sshPath -l root $host $rsyncPath $argList+';
#
# Full command to run rsync for restore on the client. The following
#
# This setting only matters if $Conf{XferMethod} = 'rsync'.
#
-$Conf{RsyncClientRestoreCmd} = '$sshPath -l root $host $rsyncPath $argList';
+$Conf{RsyncClientRestoreCmd} = '$sshPath -l root $host $rsyncPath $argList+';
#
# Share name to backup. For $Conf{XferMethod} = "rsync" this should
#
# NmbLookup command. Given an IP address, does an nmblookup on that
-# IP address. Several variables are substituted at run-time:
+# IP address. The following variables are substituted at run-time:
#
# $nmbLookupPath path to nmblookup ($Conf{NmbLookupPath})
# $host IP address
#
# NmbLookup command. Given a netbios name, finds that host by doing
-# a NetBios multicast. Several variables are substituted at run-time:
+# a NetBios lookup. Several variables are substituted at run-time:
#
# $nmbLookupPath path to nmblookup ($Conf{NmbLookupPath})
# $host NetBios name
#
# $Conf{NmbLookupFindHostCmd} = '$nmbLookupPath -B 192.168.1.255 $host';
#
+# If you use a WINS server and your machines don't respond to
+# multicast NetBios requests you can use this (replace 1.2.3.4
+# with the IP address of your WINS server):
+#
+# $Conf{NmbLookupFindHostCmd} = '$nmbLookupPath -R -U 1.2.3.4 $host';
+#
+# This is preferred over multicast since it minimizes network traffic.
+#
+# Experiment manually for your site to see what form of nmblookup command
+# works.
+#
$Conf{NmbLookupFindHostCmd} = '$nmbLookupPath $host';
#
$Conf{PingPath} = '/bin/ping';
#
-# Ping command. Several variables are substituted at run-time:
+# Ping command. The following variables are substituted at run-time:
#
# $pingPath path to ping ($Conf{PingPath})
# $host host name
#
+# Wade Brown reports that on solaris 2.6 and 2.7 ping -s returns the wrong
+# exit status (0 even on failure). Replace with "ping $host 1", which
+# gets the correct exit status but we don't get the round-trip time.
+#
$Conf{PingCmd} = '$pingPath -c 1 $host';
#
#
# $Conf{DumpPreUserCmd} = '$sshPath -l root $host /usr/bin/dumpMysql';
#
-# Various variable substitutions are available; see BackupPC_dump
-# or BackupPC_restore for the details.
+# The following variable substitutions are made at run time for
+# $Conf{DumpPreUserCmd} and $Conf{DumpPostUserCmd}:
+#
+# $type type of dump (incr or full)
+# $xferOK 1 if the dump succeeded, 0 if it didn't
+# $client client name being backed up
+# $host host name (could be different from client name if
+# $Conf{ClientNameAlias} is set)
+# $hostIP IP address of host
+# $user user name from the hosts file
+# $moreUsers list of additional users from the hosts file
+# $share the first share name
+# $shares list of all the share names
+# $XferMethod value of $Conf{XferMethod} (eg: tar, rsync, smb)
+# $sshPath value of $Conf{SshPath},
+#
+# The following variable substitutions are made at run time for
+# $Conf{RestorePreUserCmd} and $Conf{RestorePostUserCmd}:
+#
+# $client client name being backed up
+# $xferOK 1 if the restore succeeded, 0 if it didn't
+# $host host name (could be different from client name if
+# $Conf{ClientNameAlias} is set)
+# $hostIP IP address of host
+# $user user name from the hosts file
+# $moreUsers list of additional users from the hosts file
+# $share the first share name
+# $XferMethod value of $Conf{XferMethod} (eg: tar, rsync, smb)
+# $sshPath value of $Conf{SshPath},
+# $type set to "restore"
+# $bkupSrcHost host name of the restore source
+# $bkupSrcShare share name of the restore source
+# $bkupSrcNum backup number of the restore source
+# $pathHdrSrc common starting path of restore source
+# $pathHdrDest common starting path of destination
+# $fileList list of files being restored
#
$Conf{DumpPreUserCmd} = undef;
$Conf{DumpPostUserCmd} = undef;
#
# Language to use. See lib/BackupPC/Lang for the list of supported
-# languages, which include English (en), French (fr), and Spanish (es).
+# languages, which include English (en), French (fr), Spanish (es),
+# and German (de).
+#
# Currently the Language setting applies to the CGI interface and email
# messages sent to users. Log files and other text is still in English.
#
Reason_backup_failed => '#ffcccc',
Reason_backup_done => '#ccffcc',
Reason_no_ping => '#ffff99',
- Reason_backup_in_progress => '#66cc99',
Reason_backup_canceled_by_user => '#ff9900',
+ Status_backup_in_progress => '#66cc99',
};
#
projects / BackupPC.git / blobdiff