http://downloads.netgear.com/files/GPL/GPL_Source_V361j_DM111PSP_series_consumer_rele...
[bcm963xx.git] / kernel / linux / Documentation / isdn / README.act2000
1 $Id: README.act2000,v 1.1.1.1 2006/04/12 06:25:09 michaelc Exp $
2
3 This document describes the ACT2000 driver for the
4 IBM Active 2000 ISDN card.
5
6 There are 3 Types of this card available. A ISA-, MCA-, and PCMCIA-Bus
7 Version. Currently, only the ISA-Bus version of the card is supported.
8 However MCA and PCMCIA will follow soon.
9
10 The ISA-Bus Version uses 8 IO-ports. The base port address has to be set
11 manually using the DIP switches.
12
13 Setting up the DIP switches for the IBM Active 2000 ISDN card:
14
15          Note: S5 and S6 always set off!
16
17      S1  S2  S3  S4  Base-port
18      on  on  on  on  0x0200 (Factory default)
19      off on  on  on  0x0240 
20      on  off on  on  0x0280 
21      off off on  on  0x02c0 
22      on  on  off on  0x0300 
23      off on  off on  0x0340 
24      on  off off on  0x0380 
25      on  on  on  off 0xcfe0
26      off on  on  off 0xcfa0 
27      on  off on  off 0xcf60 
28      off off on  off 0xcf20 
29      on  on  off off 0xcee0 
30      off on  off off 0xcea0 
31      on  off off off 0xce60 
32      off off off off Card disabled 
33
34 IRQ is configured by software. Possible values are:
35
36   3, 5, 7, 10, 11, 12, 15 and none (polled mode)
37
38
39 The ACT2000 driver may either be built into the kernel or as a module.
40 Initialization depends on how the driver is built:
41
42 Driver built into the kernel:
43
44   The ACT2000 driver can be configured using the commandline-feature while
45   loading the kernel with LILO or LOADLIN. It accepts the following syntax:
46
47   act2000=b,p,i[,idstring]
48
49   where
50
51     b = Bus-Type      (1=ISA, 2=MCA, 3=PCMCIA)
52     p = portbase      (-1 means autoprobe)
53     i = Interrupt     (-1 means use next free IRQ, 0 means polled mode)
54
55   The idstring is an arbitrary string used for referencing the card
56   by the actctrl tool later.
57
58   Defaults used, when no parameters given at all:
59
60     1,-1,-1,""
61
62   which means: Autoprobe for an ISA card, use next free IRQ, let the
63   ISDN linklevel fill the IdString (usually "line0" for the first card).
64  
65   If you like to use more than one card, you can use the program
66   "actctrl" from the utility-package to configure additional cards.
67
68   Using the "actctrl"-utility, portbase and irq can also be changed
69   during runtime. The D-channel protocol is configured by the "dproto"
70   option of the "actctrl"-utility after loading the firmware into the
71   card's memory using the "actctrl"-utility.
72
73 Driver built as module:
74
75   The module act2000.o can be configured during modprobe (insmod) by
76   appending its parameters to the modprobe resp. insmod commandline.
77   The following syntax is accepted:
78
79     act_bus=b act_port=p act_irq=i act_id=idstring
80
81   where b, p, i and idstring have the same meanings as the parameters
82   described for the builtin version above.
83
84   Using the "actctrl"-utility, the same features apply to the modularized
85   version as to the kernel-builtin one. (i.e. loading of firmware and
86   configuring the D-channel protocol)
87
88 Loading the firmware into the card:
89
90   The firmware is supplied together with the isdn4k-utils package. It
91   can be found in the subdirectory act2000/firmware/
92
93   Assuming you have installed the utility-package correctly, the firmware
94   will be downloaded into the card using the following command:
95
96     actctrl -d idstring load /etc/isdn/bip11.btl
97
98   where idstring is the Name of the card, given during insmod-time or
99   (for kernel-builtin driver) on the kernel commandline. If only one
100   ISDN card is used, the -d isdstrin may be omitted.
101
102   For further documentation (adding more IBM Active 2000 cards), refer to
103   the manpage actctrl.8 which is included in the isdn4k-utils package.
104