git.rot13.org Git - goodfet/blob - firmware/apps/jtag/jtag430.c

   1 /*! \file jtag430.c
   2   \author Travis Goodspeed <travis at radiantmachines.com>
   3   \brief MSP430 JTAG (16-bit)
   4 */
   5
   6 #include "platform.h"
   7 #include "command.h"
   8 #include "jtag.h"
   9
  10
  11 unsigned int jtag430mode=MSP430X2MODE;
  12
  13 //! Set the program counter.
  14 void jtag430_setpc(unsigned int adr){
  15   jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
  16   jtag_dr_shift16(0x3401);// release low byte
  17   jtag_ir_shift8(IR_DATA_16BIT);
  18   jtag_dr_shift16(0x4030);//Instruction to load PC
  19   CLRTCLK;
  20   SETTCLK;
  21   jtag_dr_shift16(adr);// Value for PC
  22   CLRTCLK;
  23   jtag_ir_shift8(IR_ADDR_CAPTURE);
  24   SETTCLK;
  25   CLRTCLK ;// Now PC is set to "PC_Value"
  26   jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
  27   jtag_dr_shift16(0x2401);// low byte controlled by JTAG
  28 }
  29
  30 //! Halt the CPU
  31 void jtag430_haltcpu(){
  32   //jtag430_setinstrfetch();
  33
  34   jtag_ir_shift8(IR_DATA_16BIT);
  35   jtag_dr_shift16(0x3FFF);//JMP $+0
  36
  37   CLRTCLK;
  38   jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
  39   jtag_dr_shift16(0x2409);//set JTAG_HALT bit
  40   SETTCLK;
  41 }
  42
  43 //! Release the CPU
  44 void jtag430_releasecpu(){
  45   CLRTCLK;
  46   jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
  47   jtag_dr_shift16(0x2401);
  48   jtag_ir_shift8(IR_ADDR_CAPTURE);
  49   SETTCLK;
  50 }
  51
  52 //! Read data from address
  53 unsigned int jtag430_readmem(unsigned int adr){
  54   unsigned int toret;
  55
  56   CLRTCLK;
  57   jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
  58
  59   if(adr>0xFF)
  60     jtag_dr_shift16(0x2409);//word read
  61   else
  62     jtag_dr_shift16(0x2419);//byte read
  63   jtag_ir_shift8(IR_ADDR_16BIT);
  64   jtag_dr_shift16(adr);//address
  65   jtag_ir_shift8(IR_DATA_TO_ADDR);
  66   SETTCLK;
  67
  68   CLRTCLK;
  69   toret=jtag_dr_shift16(0x0000);//16 bit return
  70
  71   return toret;
  72 }
  73
  74 //! Write data to address.
  75 void jtag430_writemem(unsigned int adr, unsigned int data){
  76   CLRTCLK;
  77   jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
  78   if(adr>0xFF)
  79     jtag_dr_shift16(0x2408);//word write
  80   else
  81     jtag_dr_shift16(0x2418);//byte write
  82   jtag_ir_shift8(IR_ADDR_16BIT);
  83   jtag_dr_shift16(adr);
  84   jtag_ir_shift8(IR_DATA_TO_ADDR);
  85   jtag_dr_shift16(data);
  86   SETTCLK;
  87 }
  88
  89 //! Write data to flash memory.  Must be preconfigured.
  90 void jtag430_writeflashword(unsigned int adr, unsigned int data){
  91   /*
  92   CLRTCLK;
  93   jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
  94   jtag_dr_shift16(0x2408);//word write
  95   jtag_ir_shift8(IR_ADDR_16BIT);
  96   jtag_dr_shift16(adr);
  97   jtag_ir_shift8(IR_DATA_TO_ADDR);
  98   jtag_dr_shift16(data);
  99   SETTCLK;
 100
 101   //Return to read mode.
 102   CLRTCLK;
 103   jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
 104   jtag_dr_shift16(0x2409);
 105   */
 106
 107   jtag430_writemem(adr,data);
 108   CLRTCLK;
 109   jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
 110   jtag_dr_shift16(0x2409);
 111
 112   //Pulse TCLK
 113   jtag430_tclk_flashpulses(35); //35 standard
 114
 115 }
 116
 117 //! Configure flash, then write a word.
 118 void jtag430_writeflash(unsigned int adr, unsigned int data){
 119   jtag430_haltcpu();
 120
 121   //FCTL1=0xA540, enabling flash write
 122   jtag430_writemem(0x0128, 0xA540);
 123   //FCTL2=0xA540, selecting MCLK as source, DIV=1
 124   jtag430_writemem(0x012A, 0xA540);
 125   //FCTL3=0xA500, should be 0xA540 for Info Seg A on 2xx chips.
 126   jtag430_writemem(0x012C, 0xA500);
 127
 128   //Write the word itself.
 129   jtag430_writeflashword(adr,data);
 130
 131   //FCTL1=0xA500, disabling flash write
 132   jtag430_writemem(0x0128, 0xA500);
 133
 134   jtag430_releasecpu();
 135 }
 136
 137
 138
 139 //! Power-On Reset
 140 void jtag430_por(){
 141   unsigned int jtagid;
 142
 143   // Perform Reset
 144   jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
 145   jtag_dr_shift16(0x2C01); // apply
 146   jtag_dr_shift16(0x2401); // remove
 147   CLRTCLK;
 148   SETTCLK;
 149   CLRTCLK;
 150   SETTCLK;
 151   CLRTCLK;
 152   jtagid = jtag_ir_shift8(IR_ADDR_CAPTURE); // get JTAG identifier
 153   SETTCLK;
 154
 155   jtag430_writemem(0x0120, 0x5A80);   // Diabled Watchdog
 156 }
 157
 158
 159
 160 #define ERASE_GLOB 0xA50E
 161 #define ERASE_ALLMAIN 0xA50C
 162 #define ERASE_MASS 0xA506
 163 #define ERASE_MAIN 0xA504
 164 #define ERASE_SGMT 0xA502
 165
 166 //! Configure flash, then write a word.
 167 void jtag430_eraseflash(unsigned int mode, unsigned int adr, unsigned int count){
 168   jtag430_haltcpu();
 169
 170   //FCTL1= erase mode
 171   jtag430_writemem(0x0128, mode);
 172   //FCTL2=0xA540, selecting MCLK as source, DIV=1
 173   jtag430_writemem(0x012A, 0xA540);
 174   //FCTL3=0xA500, should be 0xA540 for Info Seg A on 2xx chips.
 175   jtag430_writemem(0x012C, 0xA500);
 176
 177   //Write the erase word.
 178   jtag430_writemem(adr, 0x55AA);
 179   //Return to read mode.
 180   CLRTCLK;
 181   jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
 182   jtag_dr_shift16(0x2409);
 183
 184   //Send the pulses.
 185   jtag430_tclk_flashpulses(count);
 186
 187   //FCTL1=0xA500, disabling flash write
 188   jtag430_writemem(0x0128, 0xA500);
 189
 190   jtag430_releasecpu();
 191 }
 192
 193
 194 //! Reset the TAP state machine.
 195 void jtag430_resettap(){
 196   int i;
 197   // Settle output
 198   SETTDI; //430X2
 199   SETTMS;
 200   //SETTDI; //classic
 201   SETTCK;
 202
 203   // Navigate to reset state.
 204   // Should be at least six.
 205   for(i=0;i<4;i++){
 206     CLRTCK;
 207     SETTCK;
 208   }
 209
 210   // test-logic-reset
 211   CLRTCK;
 212   CLRTMS;
 213   SETTCK;
 214   SETTMS;
 215   // idle
 216
 217
 218   /* sacred, by spec.
 219      Sometimes this isn't necessary.  */
 220   // fuse check
 221   CLRTMS;
 222   delay(50);
 223   SETTMS;
 224   CLRTMS;
 225   delay(50);
 226   SETTMS;
 227   /**/
 228
 229 }
 230
 231 //! Start JTAG, take pins
 232 void jtag430_start(){
 233   jtagsetup();
 234
 235   //Known-good starting position.
 236   //Might be unnecessary.
 237   SETTST;
 238   SETRST;
 239   delay(0xFFFF);
 240
 241   //Entry sequence from Page 67 of SLAU265A for 4-wire MSP430 JTAG
 242   CLRRST;
 243   delay(100);
 244   CLRTST;
 245   delay(50);
 246   SETTST;
 247   delay(50);
 248   SETRST;
 249   P5DIR&=~RST;
 250   delay(0xFFFF);
 251
 252   //Perform a reset and disable watchdog.
 253   jtag430_por();
 254 }
 255
 256 //! Set CPU to Instruction Fetch
 257 void jtag430_setinstrfetch(){
 258   jtag_ir_shift8(IR_CNTRL_SIG_CAPTURE);
 259
 260   // Wait until instruction fetch state.
 261   while(1){
 262     if (jtag_dr_shift16(0x0000) & 0x0080)
 263       return;
 264     CLRTCLK;
 265     SETTCLK;
 266   }
 267 }
 268
 269
 270 //! Handles classic MSP430 JTAG commands.  Forwards others to JTAG.
 271 void oldjtag430handle(unsigned char app,
 272                    unsigned char verb,
 273                    unsigned char len){
 274
 275   switch(verb){
 276   case START:
 277     //Enter JTAG mode.
 278     jtag430_start();
 279     //TAP setup, fuse check
 280     jtag430_resettap();
 281
 282     txdata(app,verb,0);
 283     break;
 284   case JTAG430_HALTCPU:
 285     jtag430_haltcpu();
 286     txdata(app,verb,0);
 287     break;
 288   case JTAG430_RELEASECPU:
 289     jtag430_releasecpu();
 290     txdata(app,verb,0);
 291     break;
 292   case JTAG430_SETINSTRFETCH:
 293     jtag430_setinstrfetch();
 294     txdata(app,verb,0);
 295     break;
 296
 297   case JTAG430_READMEM:
 298   case PEEK:
 299     cmddataword[0]=jtag430_readmem(cmddataword[0]);
 300     txdata(app,verb,2);
 301     break;
 302   case JTAG430_WRITEMEM:
 303   case POKE:
 304     jtag430_writemem(cmddatalong[0],cmddataword[2]);
 305     cmddataword[0]=jtag430_readmem(cmddatalong[0]);
 306     txdata(app,verb,2);
 307     break;
 308   case JTAG430_WRITEFLASH:
 309     jtag430_writeflash(cmddataword[0],cmddataword[1]);
 310     cmddataword[0]=jtag430_readmem(cmddataword[0]);
 311     txdata(app,verb,2);
 312     break;
 313   case JTAG430_ERASEFLASH:
 314     jtag430_eraseflash(ERASE_MASS,0xFFFE,0xFFFF);
 315     jtag430_eraseflash(ERASE_MASS,0xFFFE,0xFFFF);
 316     jtag430_eraseflash(ERASE_MASS,0xFFFE,0xFFFF);
 317     txdata(app,verb,0);
 318     break;
 319   case JTAG430_SETPC:
 320     jtag430_setpc(cmddataword[0]);
 321     txdata(app,verb,0);
 322     break;
 323   default:
 324     jtaghandle(app,verb,len);
 325   }
 326   jtag430_resettap();
 327 }
 328
 329 //! Handles unique MSP430 JTAG commands.  Forwards others to JTAG.
 330 void jtag430handle(unsigned char app,
 331                    unsigned char verb,
 332                    unsigned char len){
 333   switch(jtag430mode){
 334   case MSP430MODE:
 335     return oldjtag430handle(app,verb,len);
 336   case MSP430X2MODE:
 337     return jtag430x2handle(app,verb,len);
 338   default:
 339     txdata(app,NOK,0);
 340   }
 341 }