#!/usr/bin/env python

#GoodFET SPI Flash Client
#by Travis Goodspeed

#N.B.,
#Might be Winbond W25x80-specific.

import sys;
import binascii;

from GoodFET import GoodFET;
from intelhex import IntelHex;

if(len(sys.argv)==1):
    print "Usage: %s verb [objects]\n" % sys.argv[0];
    print "%s info" % sys.argv[0];
    print "%s dump $foo.hex [0x$start 0x$stop]" % sys.argv[0];
    print "%s erase" % sys.argv[0];
    print "%s write $foo.hex [0x$start 0x$stop]" % sys.argv[0];
    print "%s verify $foo.hex [0x$start 0x$stop]" % sys.argv[0];
    print "%s peek 0x$start [0x$stop]" % sys.argv[0];
    print "%s poke 0x$adr 0x$val" % sys.argv[0];
    sys.exit();

#Initailize FET and set baud rate
client=GoodFET();
client.serInit("/dev/ttyUSB0")

client.SPIsetup();

if(sys.argv[1]=="test"):
    result="";
    dropped=0;
    for i in range(40):
        data=client.SPIjedec();
        if ord(data[1])==0xFF:
            result+="-";
            dropped=dropped+1;
        else:
            result+="+";
    print "Connection Test: (- is bad)\n%s" % result;
    print "%i misreads" % dropped;
    if(dropped==40):
        print "No successful reads.  Is the chip wired correctly?";
    elif(dropped>0):
        print "Some success, some failures.  Is a wire loose?";
    else:
        print "All reads succeeded.  Wiring is probably good.";

if(sys.argv[1]=="info"):
    data=client.SPIjedec();
    print "Ident as %s\nManufacturer: %02x %s\nType: %02x\nCapacity: %02x" % (
        client.SPIjedecstr(),
        ord(data[1]),client.SPIjedecmanstr(),
        ord(data[2]),
        ord(data[3]));

if(sys.argv[1]=="dump"):
    f = sys.argv[2];
    start=0x0000;
    stop=0x100000; #TODO, adjust this by the JEDEC size parameter.
    if(len(sys.argv)>3):
        start=int(sys.argv[3],16);
    if(len(sys.argv)>4):
        stop=int(sys.argv[4],16);
    
    

    print "Dumping code from %06x to %06x as %s." % (start,stop,f);
    file = open(f, mode='wb')

    i=start;
    while i<=stop:
        data=client.SPIpeekblock(i);
        
        
        if(i%0x100==0):
            print "Dumped %06x."%i;
        for j in data:
            file.write(j);
            i+=1;
    file.close()
if(sys.argv[1]=="erase"):
  client.SPIchiperase();

if(sys.argv[1]=="peek"):
    start=0x0000;
    if(len(sys.argv)>2):
        start=int(sys.argv[2],16);
    stop=start;
    if(len(sys.argv)>3):
        stop=int(sys.argv[3],16);
    print "Peeking from %06x to %06x." % (start,stop);
    while start<=stop:
        print "%06x: %02x" % (start,client.SPIpeek(start));
        start=start+1;

if(sys.argv[1]=="poke"):
    start=0x0000;
    val=0x00;
    if(len(sys.argv)>2):
        start=int(sys.argv[2],16);
    if(len(sys.argv)>3):
        val=int(sys.argv[3],16);
    print "Poking %06x to become %02x." % (start,val);
    client.SPIpokebyte(start,val);