+ #Don't change these while the radio is active.
+ self.pokebysym("FSCAL3" , 0xEA) # Frequency synthesizer calibration.
+ self.pokebysym("FSCAL2" , 0x2A) # Frequency synthesizer calibration.
+ self.pokebysym("FSCAL1" , 0x00) # Frequency synthesizer calibration.
+ self.pokebysym("FSCAL0" , 0x1F) # Frequency synthesizer calibration.
+
+ if band=="ismeu" or band=="eu":
+ print "There is no official eu band for dash7."
+ self.pokebysym("FREQ2" , 0x21) # Frequency control word, high byte.
+ self.pokebysym("FREQ1" , 0x71) # Frequency control word, middle byte.
+ self.pokebysym("FREQ0" , 0x7a) # Frequency control word, low byte.
+ elif band=="ismus" or band=="us":
+ print "There is no official us band for dash7."
+ self.pokebysym("FREQ2" , 0x22) # Frequency control word, high byte.
+ self.pokebysym("FREQ1" , 0xB1) # Frequency control word, middle byte.
+ self.pokebysym("FREQ0" , 0x3B) # Frequency control word, low byte.
+ elif band=="ismlf" or band=="lf":
+ # 433.9198 MHz, same as Simpliciti.
+ self.pokebysym("FREQ2" , 0x10) # Frequency control word, high byte.
+ self.pokebysym("FREQ1" , 0xB0) # Frequency control word, middle byte.
+ self.pokebysym("FREQ0" , 0x71) # Frequency control word, low byte.
+ elif band=="none":
+ pass;
+ else:
+ #Got a frequency, not a band.
+ self.RF_setfreq(eval(band));
+ self.pokebysym("MDMCFG4" , 0x8B) # 62.5 kbps w/ 200 kHz filter
+ self.pokebysym("MDMCFG3" , 0x3B)
+ self.pokebysym("MDMCFG2" , 0x11)
+ self.pokebysym("MDMCFG1" , 0x02)
+ self.pokebysym("MDMCFG0" , 0x53)
+ self.pokebysym("CHANNR" , 0x00) # Channel zero.
+ self.pokebysym("DEVIATN" , 0x50) # 50 kHz deviation
+
+ self.pokebysym("FREND1" , 0xB6) # Front end RX configuration.
+ self.pokebysym("FREND0" , 0x10) # Front end RX configuration.
+ self.pokebysym("MCSM2" , 0x1E)
+ self.pokebysym("MCSM1" , 0x3F)
+ self.pokebysym("MCSM0" , 0x30)
+ self.pokebysym("FOCCFG" , 0x1D) # Frequency Offset Compensation Configuration.
+ self.pokebysym("BSCFG" , 0x1E) # 6.25% data error rate
+
+ self.pokebysym("AGCCTRL2" , 0xC7) # AGC control.
+ self.pokebysym("AGCCTRL1" , 0x00) # AGC control.
+ self.pokebysym("AGCCTRL0" , 0xB2) # AGC control.
+
+ self.pokebysym("TEST2" , 0x81) # Various test settings.
+ self.pokebysym("TEST1" , 0x35) # Various test settings.
+ self.pokebysym("TEST0" , 0x09) # Various test settings.
+ self.pokebysym("PA_TABLE0", 0xc0) # Max output power.
+ self.pokebysym("PKTCTRL1" , 0x04) # Packet automation control, w/ lqi
+ #self.pokebysym("PKTCTRL1" , 0x00) # Packet automation control. w/o lqi
+ self.pokebysym("PKTCTRL0" , 0x05) # Packet automation control, w/ checksum.
+ #self.pokebysym("PKTCTRL0" , 0x00) # Packet automation control, w/o checksum, fixed length
+ self.pokebysym("ADDR" , 0x01) # Device address.
+ self.pokebysym("PKTLEN" , 0xFF) # Packet length.