'goodfet.nrf carrier' works.

[goodfet] / client / goodfet.nrf

diff --git a/client/goodfet.nrf b/client/goodfet.nrf
index 6cb92ae..54f816e 100755 (executable)
--- a/client/goodfet.nrf
+++ b/client/goodfet.nrf
@@ -11,50 +11,77 @@ import time;
 from GoodFETNRF import GoodFETNRF;
 from intelhex import IntelHex;
 
+def printpacket(packet):
+    s="";
+    i=0;
+    for foo in packet:
+        i=i+1;
+        if i>client.packetlen: break;
+        s="%s %02x" % (s,ord(foo));
+    print "%s" %s;
+
+def printconfig():
+    print "SMAC  0x%010x" % client.RF_getsmac();
+    print "TMAC  0x%010x" % client.RF_gettmac();
+    print "Freq    %10i MHz" % (client.RF_getfreq()/10**6);
+    print "PacketLen %02i bytes" % client.RF_getpacketlen();
+    print "MacLen    %2i bytes" % client.RF_getmaclen();
+
 if(len(sys.argv)==1):
     print "Usage: %s verb [objects]\n" % sys.argv[0];
     print "%s info" % sys.argv[0];
     print "%s test" % sys.argv[0];
+    print "%s regs" % sys.argv[0];
+    print "%s sniffob\n\tSniffs OpenBeacon traffic." % sys.argv[0];
+    print "%s carrier [freq]\n\tHolds a carrier on [freq] Hz." % sys.argv[0];
     sys.exit();
 
 #Initialize FET and set baud rate
 client=GoodFETNRF();
-print "Connecting."
 client.serInit()
 
-print "Connected."
 client.NRFsetup();
-print "Setup."
-client.status();
 
+if(sys.argv[1]=="info"):
+    printconfig();
 
 if(sys.argv[1]=="test"):
     # Set PWR_UP=1 and PRIM_RX=0 in CONFIG.
     client.poke(0x00,2);
     #Delay of 1.5ms by round-trip.
     # Set CONT_WAVE, PLL_LOCK, and 0dBm in RF_SETUP
-    client.poke(0x06,8+10+4+2); 
-    client.RF_freq(2480 * 10**6);
+    client.poke(0x06,8+10+4+2);
+    client.RF_setfreq(2480 * 10**6);
     
     #Print registers, just for fun.
-    print "SMAC was %010x" % client.RF_getsmac();
+    printconfig();
     
     client.poke(0x0A,0xDEADBEEF,5);
-    print "SMAC set to %010x" % client.RF_getsmac();
+    #print "SMAC set to %010x" % client.RF_getsmac();
     if client.RF_getsmac()!=0xdeadbeef:
         print "ERROR: Failed to set MAC address.";
 
+if(sys.argv[1]=="carrier"):
+    if len(sys.argv)>2:
+        client.RF_setfreq(eval(sys.argv[2]));
+    client.RF_carrier();
+    printconfig();
+    print "\nHolding a carrier wave.";
+    while(1):
+        time.sleep(1);
 if(sys.argv[1]=="regs"):
-    for r in range(0,30):
-        print "r[0x%02x]=0x%02x" % (r,client.peek(r));
+    for r in range(0,0x20):
+        print "r[0x%02x]=0x%010x" % (r,client.peek(r));
 
 if(sys.argv[1]=="sniffob"):
-    #Reversal of transmitter code from nRF_CMD.c
+    #Reversal of transmitter code from nRF_CMD.c of OpenBeacon
+    #TODO remove all poke() calls.
+    
     client.poke(0x00,0x00); #Stop nRF
     client.poke(0x01,0x00); #Disable Shockburst
     client.poke(0x02,0x01); #Set RX Pipe 0
-    client.poke(0x03,0x03); #SETUP_AW for 5-byte addresses.
-    client.RF_freq(2481 * 10**6);
+    client.RF_setmaclen(5); # SETUP_AW for 5-byte addresses.
+    client.RF_setfreq(2481 * 10**6);
     client.poke(0x06,0x09); #2MBps, -18dBm in RF_SETUP
     client.poke(0x07,0x78); #Reset status register
     
@@ -65,23 +92,19 @@ if(sys.argv[1]=="sniffob"):
     client.RF_settmac(0x424541434F);
     
     #Set packet length of 16.
-    client.poke(0x11,16);
+    client.RF_setpacketlen(16);
     
-    client.status();
     #Power radio, prime for RX, checksum.
     client.poke(0x00,0x70|0x03|0x08);
     
-    
-    print "Listening as %010x on channel %03i" % (client.RF_getsmac(),client.peek(0x05));
+    print "Listening as %010x on %i MHz" % (client.RF_getsmac(),
+                                           client.RF_getfreq()/10**6);
     #Now we're ready to get packets.
     
     while 1:
         packet=None;
         while packet==None:
-            time.sleep(0.1);
-            client.status();
+            #time.sleep(0.1);
             packet=client.RF_rxpacket();
-        s="";
-        for foo in packet:
-            s="%s %02x" % (s,ord(foo));
-        print "Got %s" %s;
+        printpacket(packet);
+        sys.stdout.flush();