A major refactor of the GoodFET firmware build system and apps to give better

[goodfet] / firmware / apps / glitch / glitch.c

diff --git a/firmware/apps/glitch/glitch.c b/firmware/apps/glitch/glitch.c
index f337e42..40e8122 100644 (file)
--- a/firmware/apps/glitch/glitch.c
+++ b/firmware/apps/glitch/glitch.c
@@ -11,6 +11,29 @@
 #include "command.h"
 #include "glitch.h"
 
+//! Handles a monitor command.
+void glitch_handle_fn( uint8_t const app,
+                                          uint8_t const verb,
+                                          uint32_t const len);
+
+// define the glitch app's app_t
+app_t const glitch_app = {
+
+       /* app number */
+       GLITCH,
+
+       /* handle fn */
+       glitch_handle_fn,
+
+       /* name */
+       "GLITCH",
+
+       /* desc */
+       "\tThe GLITCH app adds support for doing glitch research.\n"
+       "\tSee the TI example MSP430x261x_dac12_01.c for usage of the DAC.\n"
+       "\tThis module sends odd and insufficient voltages on P6.6/DAC0\n"
+       "\tin order to bypass security restrictions of target devices.\n"
+};
 
 //! Call this before the function to be glitched.
 void glitchprime(){
@@ -29,9 +52,10 @@ void glitchsetup(){
   //Set GSEL high to disable glitching.
   
   //Normal voltage, use resistors instead of output.
-  P5DIR=0x80;   //ONLY glitch pin is output.
+  //P5DIR=0x80;   //ONLY glitch pin is output.
+  P5DIR|=0x80;   //glitch pin is output.
   P5OUT|=0x80;  //It MUST begin high.
-  P5REN|=0xFF;  //Resistors pull high and low weakly.
+  //P5REN|=0x7F;  //Resistors pull high and low weakly.
   
   P6DIR|=BIT6+BIT5;
   P6OUT|=BIT6+BIT5;
@@ -39,19 +63,25 @@ void glitchsetup(){
   WDTCTL = WDTPW + WDTHOLD;             // Stop WDT
   TACTL = TASSEL1 + TACLR;              // SMCLK, clear TAR
   CCTL0 = CCIE;                         // CCR0 interrupt enabled
-  CCR0 = glitchcount+0x15; //clock divider
-  TACTL |= MC_3;
-  _EINT();                              // Enable interrupts 
+  CCR0 = glitchcount+0x10;              // Compare Value
+  TACTL |= MC_2;                        // continuous mode.
 #endif
 }
 
 // Timer A0 interrupt service routine
 interrupt(TIMERA0_VECTOR) Timer_A (void){
-  P5OUT&=~BIT7;//Glitch
-  //P5DIR=BIT7; //All else high impedance.
-  P5OUT|=BIT7;//Normal
-  TACTL |= MC0;// Stop Timer_A;
+  //This oughtn't be necessary, but glitches repeat without it.
+  TACTL=0; //disable counter.
+  
   
+  P5OUT^=BIT7;//Glitch
+  //asm("nop"); //delay deepens glitch.
+  P5OUT^=BIT7;//Normal
+  
+  //This oughtn't be necessary, but glitches repeat without it.
+  TACTL=0; //disable counter.
+  
+  //P5OUT^=BIT7;//Normal
   return;
 }
 
@@ -66,7 +96,7 @@ void glitchapp(u8 app){
 
 //! Set glitching voltages.
 void glitchvoltages(u16 gnd, u16 vcc){
-  int i;
+  
   //debugstr("Set glitching voltages: GND and VCC");
   //debughex(gnd);
   //debughex(vcc);
@@ -78,6 +108,7 @@ void glitchvoltages(u16 gnd, u16 vcc){
   */
   
   #ifdef DAC12IR
+  int i;
   ADC12CTL0 = REF2_5V + REFON;                  // Internal 2.5V ref on
   // Delay here for reference to settle.
   for(i=0;i!=0xFFFF;i++) asm("nop");
@@ -94,10 +125,10 @@ void glitchrate(u16 rate){
 }
 
 //! Handles a monitor command.
-void glitchhandle(unsigned char app,
-                 unsigned char verb,
-                 unsigned long len){
-  P1OUT&=~1;
+void glitch_handle_fn( uint8_t const app,
+                                          uint8_t const verb,
+                                          uint32_t const len)
+{
   switch(verb){
   case GLITCHVOLTAGES:
     glitchvoltages(cmddataword[0],
@@ -111,30 +142,39 @@ void glitchhandle(unsigned char app,
   case GLITCHVERB:
     //FIXME parameters don't work yet.
     glitchprime();
+    TAR=0; //Reset clock.
     handle(cmddata[0],cmddata[1],0);
+    TACTL |= MC0;// Stop Timer_A;
     break;
   case GLITCHTIME:
+    debugstr("Measuring start time.");
     _DINT();//disable interrupts
     TACTL=0; //clear dividers
     TACTL|=TACLR; //clear config
-    TACTL|=TASSEL_SMCLK| //smclk source
-      MC_2; //continuout mode.
+    TACTL|=
+      TASSEL_SMCLK //smclk source
+      | MC_2; //continuous mode.
     
     //perform the function
     silent++;//Don't want the function to return anything.
+    TAR=0;
     handle(cmddata[0],cmddata[1],0);
-    silent--;
     cmddataword[0]=TAR; //Return counter.
+    silent--;
+    debugstr("Measured start time.");
+    debughex(cmddataword[0]);
     txdata(app,verb,2);
     break;
   case START:
-    glitchvoltages(0xFFF,0);//Inverted VCC and GND.
+    //Testing mode, for looking at the glitch waveform.
+    glitchvoltages(0,0xFFF);//Minimum glitch, for noise test.
+    //glitchvoltages(0,0);//Drop VCC
+    //glitchvoltages(0xFFF,0xFFF);//Raise Ground
     P5OUT|=BIT7;//Normal
     P5DIR|=BIT7;
     while(1){
       P5OUT&=~BIT7;//Glitch
-      //asm("nop");//asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");
-      asm("nop"); //Not necessary.
+      //asm("nop"); //Not Necessary
       P5OUT|=BIT7;//Normal
       asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");
       asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");