Cleaning up the glitching scripts.

[goodfet] / firmware / apps / glitch / glitch.c

diff --git a/firmware/apps/glitch/glitch.c b/firmware/apps/glitch/glitch.c
index 56de8c3..8b43594 100644 (file)
--- a/firmware/apps/glitch/glitch.c
+++ b/firmware/apps/glitch/glitch.c
@@ -27,30 +27,38 @@ void glitchprime(){
 void glitchsetup(){
 #ifdef DAC12IR
   //Set GSEL high to disable glitching.
-
-  P5DIR|=0x80;
-  P6DIR|=BIT6+BIT5;
   
-  P5OUT|=0x80;
+  //Normal voltage, use resistors instead of output.
+  //P5DIR=0x80;   //ONLY glitch pin is output.
+  P5DIR|=0x80;   //glitch pin is output.
+  P5OUT|=0x80;  //It MUST begin high.
+  //P5REN|=0x7F;  //Resistors pull high and low weakly.
+  
+  P6DIR|=BIT6+BIT5;
   P6OUT|=BIT6+BIT5;
   
   WDTCTL = WDTPW + WDTHOLD;             // Stop WDT
   TACTL = TASSEL1 + TACLR;              // SMCLK, clear TAR
   CCTL0 = CCIE;                         // CCR0 interrupt enabled
-  CCR0 = glitchcount+0x15; //clock divider
-  TACTL |= MC_3;
-  _EINT();                              // Enable interrupts 
+  CCR0 = glitchcount+0x10;              // Compare Value
+  TACTL |= MC_2;                        // continuous mode.
 #endif
 }
 
 // Timer A0 interrupt service routine
-interrupt(TIMERA0_VECTOR) Timer_A (void)
-{
-  P5OUT&=~BIT7;//Glitch
-  //P5DIR=BIT7; //All else high impedance.
-  P5OUT|=BIT7;//Normal
-  TACTL |= MC0;// Stop Timer_A;
+interrupt(TIMERA0_VECTOR) Timer_A (void){
+  //This oughtn't be necessary, but glitches repeat without it.
+  TACTL=0; //disable counter.
+  
   
+  P5OUT^=BIT7;//Glitch
+  //asm("nop"); //delay deepens glitch.
+  P5OUT^=BIT7;//Normal
+  
+  //This oughtn't be necessary, but glitches repeat without it.
+  TACTL=0; //disable counter.
+  
+  //P5OUT^=BIT7;//Normal
   return;
 }
 
@@ -70,6 +78,12 @@ void glitchvoltages(u16 gnd, u16 vcc){
   //debughex(gnd);
   //debughex(vcc);
   
+  /** N.B., because this is confusing as hell.  As per Page 86 of
+      SLAS541F, P6SEL is not what controls the use of the DAC0/DAC1
+      functions on P6.6 and P6.5.  Instead, CAPD or DAC12AMP>0 sets
+      the state.
+  */
+  
   #ifdef DAC12IR
   ADC12CTL0 = REF2_5V + REFON;                  // Internal 2.5V ref on
   // Delay here for reference to settle.
@@ -90,7 +104,6 @@ void glitchrate(u16 rate){
 void glitchhandle(unsigned char app,
                  unsigned char verb,
                  unsigned long len){
-  P1OUT&=~1;
   switch(verb){
   case GLITCHVOLTAGES:
     glitchvoltages(cmddataword[0],
@@ -104,30 +117,35 @@ void glitchhandle(unsigned char app,
   case GLITCHVERB:
     //FIXME parameters don't work yet.
     glitchprime();
+    TAR=0; //Reset clock.
     handle(cmddata[0],cmddata[1],0);
+    TACTL |= MC0;// Stop Timer_A;
     break;
   case GLITCHTIME:
     _DINT();//disable interrupts
     TACTL=0; //clear dividers
     TACTL|=TACLR; //clear config
     TACTL|=TASSEL_SMCLK| //smclk source
-      MC_2; //continuout mode.
+      MC_2; //continuous mode.
     
     //perform the function
     silent++;//Don't want the function to return anything.
+    TAR=0;
     handle(cmddata[0],cmddata[1],0);
-    silent--;
     cmddataword[0]=TAR; //Return counter.
+    silent--;
     txdata(app,verb,2);
     break;
   case START:
-    glitchvoltages(0xFFF,0);//Inverted VCC and GND.
+    //Testing mode, for looking at the glitch waveform.
+    glitchvoltages(0,0xFFF);//Minimum glitch, for noise test.
+    //glitchvoltages(0,0);//Drop VCC
+    //glitchvoltages(0xFFF,0xFFF);//Raise Ground
     P5OUT|=BIT7;//Normal
     P5DIR|=BIT7;
     while(1){
       P5OUT&=~BIT7;//Glitch
-      //asm("nop");//asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");
-      asm("nop"); //Not necessary.
+      //asm("nop"); //Not Necessary
       P5OUT|=BIT7;//Normal
       asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");
       asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");