#include "platform.h"
#include "command.h"
-#include "jtag.h"
+#include "jtag430.h"
+//! Handles classic MSP430 JTAG commands. Forwards others to JTAG.
+void jtag430_handle_fn(uint8_t const app,
+ uint8_t const verb,
+ uint32_t const len);
+
+// define the jtag430 app's app_t
+app_t const jtag430_app = {
+ /* app number */
+ JTAG430,
+
+ /* handle fn */
+ jtag430_handle_fn,
+
+ /* name */
+ "JTAG430",
+
+ /* desc */
+ "\tThe JTAG430 app adds to the basic JTAG app\n"
+ "\tsupport for JTAG'ing MSP430 devices.\n"
+};
unsigned int jtag430mode=MSP430X2MODE;
-//! Set the program counter.
-void jtag430_setpc(unsigned int adr){
- jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
- jtag_dr_shift16(0x3401);// release low byte
- jtag_ir_shift8(IR_DATA_16BIT);
- jtag_dr_shift16(0x4030);//Instruction to load PC
+unsigned int drwidth=16;
+
+//! Shift an address width of data
+uint32_t jtag430_shift_addr( uint32_t addr )
+{
+ if (!in_run_test_idle())
+ {
+ debugstr("Not in run-test-idle state");
+ return 0;
+ }
+
+ // get intot the right state
+ jtag_capture_dr();
+ jtag_shift_register();
+
+ // shift DR, then idle
+ return jtag_trans_n(addr, drwidth, MSB);
+}
+
+//! Set a register.
+void jtag430_setr(u8 reg, u16 val){
+ jtag_ir_shift_8(IR_CNTRL_SIG_16BIT);
+ jtag_dr_shift_16(0x3401);// release low byte
+ jtag_ir_shift_8(IR_DATA_16BIT);
+
+ //0x4030 is "MOV #foo, r0"
+ //Right-most field is register, so 0x4035 loads r5
+ jtag_dr_shift_16(0x4030+reg);
CLRTCLK;
SETTCLK;
- jtag_dr_shift16(adr);// Value for PC
+ jtag_dr_shift_16(val);// Value for the register
CLRTCLK;
- jtag_ir_shift8(IR_ADDR_CAPTURE);
+ jtag_ir_shift_8(IR_ADDR_CAPTURE);
SETTCLK;
- CLRTCLK ;// Now PC is set to "PC_Value"
- jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
- jtag_dr_shift16(0x2401);// low byte controlled by JTAG
+ CLRTCLK ;// Now reg is set to new value.
+ jtag_ir_shift_8(IR_CNTRL_SIG_16BIT);
+ jtag_dr_shift_16(0x2401);// low byte controlled by JTAG
+}
+
+//! Set the program counter.
+void jtag430_setpc(unsigned int adr){
+ jtag430_setr(0,adr);
}
//! Halt the CPU
void jtag430_haltcpu(){
//jtag430_setinstrfetch();
- jtag_ir_shift8(IR_DATA_16BIT);
- jtag_dr_shift16(0x3FFF);//JMP $+0
+ jtag_ir_shift_8(IR_DATA_16BIT);
+ jtag_dr_shift_16(0x3FFF);//JMP $+0
CLRTCLK;
- jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
- jtag_dr_shift16(0x2409);//set JTAG_HALT bit
+ jtag_ir_shift_8(IR_CNTRL_SIG_16BIT);
+ jtag_dr_shift_16(0x2409);//set JTAG_HALT bit
SETTCLK;
}
//! Release the CPU
void jtag430_releasecpu(){
CLRTCLK;
- jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
- jtag_dr_shift16(0x2401);
- jtag_ir_shift8(IR_ADDR_CAPTURE);
+ //debugstr("Releasing target MSP430.");
+
+ /*
+ jtag_ir_shift_8(IR_CNTRL_SIG_16BIT);
+ jtag_dr_shift_16(0x2C01); //Apply reset.
+ jtag_dr_shift_16(0x2401); //Release reset.
+ */
+ jtag_ir_shift_8(IR_CNTRL_SIG_RELEASE);
SETTCLK;
}
//! Read data from address
unsigned int jtag430_readmem(unsigned int adr){
unsigned int toret;
+ jtag430_haltcpu();
CLRTCLK;
- jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
+ jtag_ir_shift_8(IR_CNTRL_SIG_16BIT);
if(adr>0xFF)
- jtag_dr_shift16(0x2409);//word read
+ jtag_dr_shift_16(0x2409);//word read
else
- jtag_dr_shift16(0x2419);//byte read
- jtag_ir_shift8(IR_ADDR_16BIT);
- jtag_dr_shift16(adr);//address
- jtag_ir_shift8(IR_DATA_TO_ADDR);
+ jtag_dr_shift_16(0x2419);//byte read
+ jtag_ir_shift_8(IR_ADDR_16BIT);
+ jtag430_shift_addr(adr);//address
+ jtag_ir_shift_8(IR_DATA_TO_ADDR);
SETTCLK;
CLRTCLK;
- toret=jtag_dr_shift16(0x0000);//16 bit return
+ toret=jtag_dr_shift_16(0x0000);//16 bit return
return toret;
}
//! Write data to address.
void jtag430_writemem(unsigned int adr, unsigned int data){
CLRTCLK;
- jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
+ jtag_ir_shift_8(IR_CNTRL_SIG_16BIT);
if(adr>0xFF)
- jtag_dr_shift16(0x2408);//word write
+ jtag_dr_shift_16(0x2408);//word write
else
- jtag_dr_shift16(0x2418);//byte write
- jtag_ir_shift8(IR_ADDR_16BIT);
- jtag_dr_shift16(adr);
- jtag_ir_shift8(IR_DATA_TO_ADDR);
- jtag_dr_shift16(data);
+ jtag_dr_shift_16(0x2418);//byte write
+ jtag_ir_shift_8(IR_ADDR_16BIT);
+ jtag430_shift_addr(adr);
+ jtag_ir_shift_8(IR_DATA_TO_ADDR);
+ jtag_dr_shift_16(data);
SETTCLK;
}
//! Write data to flash memory. Must be preconfigured.
void jtag430_writeflashword(unsigned int adr, unsigned int data){
- /*
+
CLRTCLK;
- jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
- jtag_dr_shift16(0x2408);//word write
- jtag_ir_shift8(IR_ADDR_16BIT);
- jtag_dr_shift16(adr);
- jtag_ir_shift8(IR_DATA_TO_ADDR);
- jtag_dr_shift16(data);
+ jtag_ir_shift_8(IR_CNTRL_SIG_16BIT);
+ jtag_dr_shift_16(0x2408);//word write
+ jtag_ir_shift_8(IR_ADDR_16BIT);
+ jtag430_shift_addr(adr);
+ jtag_ir_shift_8(IR_DATA_TO_ADDR);
+ jtag_dr_shift_16(data);
SETTCLK;
//Return to read mode.
CLRTCLK;
- jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
- jtag_dr_shift16(0x2409);
- */
+ jtag_ir_shift_8(IR_CNTRL_SIG_16BIT);
+ jtag_dr_shift_16(0x2409);
+ /*
jtag430_writemem(adr,data);
CLRTCLK;
- jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
- jtag_dr_shift16(0x2409);
+ jtag_ir_shift_8(IR_CNTRL_SIG_16BIT);
+ jtag_dr_shift_16(0x2409);
+ */
//Pulse TCLK
jtag430_tclk_flashpulses(35); //35 standard
-
}
//! Configure flash, then write a word.
//FCTL2=0xA540, selecting MCLK as source, DIV=1
jtag430_writemem(0x012A, 0xA540);
//FCTL3=0xA500, should be 0xA540 for Info Seg A on 2xx chips.
- jtag430_writemem(0x012C, 0xA500);
+ jtag430_writemem(0x012C, 0xA500); //all but info flash.
+ //if(jtag430_readmem(0x012C));
//Write the word itself.
jtag430_writeflashword(adr,data);
//FCTL1=0xA500, disabling flash write
jtag430_writemem(0x0128, 0xA500);
- jtag430_releasecpu();
+ //jtag430_releasecpu();
}
//! Power-On Reset
void jtag430_por(){
- unsigned int jtagid;
-
// Perform Reset
- jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
- jtag_dr_shift16(0x2C01); // apply
- jtag_dr_shift16(0x2401); // remove
+ jtag_ir_shift_8(IR_CNTRL_SIG_16BIT);
+ jtag_dr_shift_16(0x2C01); // apply
+ jtag_dr_shift_16(0x2401); // remove
CLRTCLK;
SETTCLK;
CLRTCLK;
SETTCLK;
CLRTCLK;
- jtagid = jtag_ir_shift8(IR_ADDR_CAPTURE); // get JTAG identifier
+ jtagid = jtag_ir_shift_8(IR_ADDR_CAPTURE); // get JTAG identifier
SETTCLK;
jtag430_writemem(0x0120, 0x5A80); // Diabled Watchdog
#define ERASE_SGMT 0xA502
//! Configure flash, then write a word.
-void jtag430_eraseflash(unsigned int mode, unsigned int adr, unsigned int count){
+void jtag430_eraseflash(unsigned int mode, unsigned int adr, unsigned int count,
+ unsigned int info){
jtag430_haltcpu();
//FCTL1= erase mode
//FCTL2=0xA540, selecting MCLK as source, DIV=1
jtag430_writemem(0x012A, 0xA540);
//FCTL3=0xA500, should be 0xA540 for Info Seg A on 2xx chips.
- jtag430_writemem(0x012C, 0xA500);
+ if(info)
+ jtag430_writemem(0x012C, 0xA540);
+ else
+ jtag430_writemem(0x012C, 0xA500);
//Write the erase word.
jtag430_writemem(adr, 0x55AA);
//Return to read mode.
CLRTCLK;
- jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
- jtag_dr_shift16(0x2409);
+ jtag_ir_shift_8(IR_CNTRL_SIG_16BIT);
+ jtag_dr_shift_16(0x2409);
//Send the pulses.
jtag430_tclk_flashpulses(count);
//FCTL1=0xA500, disabling flash write
jtag430_writemem(0x0128, 0xA500);
- jtag430_releasecpu();
+ //jtag430_releasecpu();
}
SETTDI; //430X2
SETTMS;
//SETTDI; //classic
- SETTCK;
+ jtag_tcktock();
// Navigate to reset state.
// Should be at least six.
for(i=0;i<4;i++){
- CLRTCK;
- SETTCK;
+ jtag_tcktock();
}
// test-logic-reset
- CLRTCK;
CLRTMS;
- SETTCK;
+ jtag_tcktock();
SETTMS;
// idle
}
+
+//! Get the JTAG ID
+unsigned char jtag430x2_jtagid(){
+ jtag430_resettap();
+ jtagid = jtag_ir_shift_8(IR_BYPASS);
+ if(jtagid!=0x89 && jtagid!=0x91){
+ debugstr("Unknown JTAG ID");
+ debughex(jtagid);
+ }
+ return jtagid;
+}
//! Start JTAG, take pins
-void jtag430_start(){
- jtagsetup();
+unsigned char jtag430x2_start(){
+ jtag_setup();
//Known-good starting position.
//Might be unnecessary.
SETTST;
SETRST;
+
delay(0xFFFF);
//Entry sequence from Page 67 of SLAU265A for 4-wire MSP430 JTAG
CLRRST;
- delay(100);
+ delay(20);//10
CLRTST;
- delay(50);
+
+ delay(10);//5
SETTST;
- delay(50);
+ msdelay(10);//5
SETRST;
P5DIR&=~RST;
+
delay(0xFFFF);
+ //Perform a reset and disable watchdog.
+ return jtag430x2_jtagid();
+}
+
+
+//! Start JTAG, take pins
+void jtag430_start(){
+ jtag_setup();
+
+ //Known-good starting position.
+ //Might be unnecessary.
+ SETTST;
+ SETRST;
+ delay(0xFFFF);
+
+
+ #ifndef SBWREWRITE
+ //Entry sequence from Page 67 of SLAU265A for 4-wire MSP430 JTAG
+ CLRRST;
+ delay(100); //100
+ CLRTST;
+ delay(50); //50
+ SETTST;
+ delay(50); //50
+ SETRST;
+ P5DIR&=~RST;
+ delay(0xFFFF);
+ #endif
+
//Perform a reset and disable watchdog.
jtag430_por();
+ jtag430_writemem(0x120,0x5a80);//disable watchdog
+
+ jtag430_haltcpu();
+}
+
+//! Stop JTAG.
+void jtag430_stop(){
+ debugstr("Exiting JTAG.");
+ jtag_setup();
+
+ //Known-good starting position.
+ //Might be unnecessary.
+ //SETTST;
+ CLRTST;
+ SETRST;
+ delay(0xFFFF);
+
+ //Entry sequence from Page 67 of SLAU265A for 4-wire MSP430 JTAG
+ CLRRST;
+ delay(0xFFFF);
+ SETRST;
+ //P5DIR&=~RST;
+ //delay(0xFFFF);
+
}
//! Set CPU to Instruction Fetch
void jtag430_setinstrfetch(){
- jtag_ir_shift8(IR_CNTRL_SIG_CAPTURE);
+
+ jtag_ir_shift_8(IR_CNTRL_SIG_CAPTURE);
// Wait until instruction fetch state.
while(1){
- if (jtag_dr_shift16(0x0000) & 0x0080)
+ if (jtag_dr_shift_16(0x0000) & 0x0080)
return;
CLRTCLK;
SETTCLK;
}
+
+
+
//! Handles classic MSP430 JTAG commands. Forwards others to JTAG.
-void oldjtag430handle(unsigned char app,
- unsigned char verb,
- unsigned char len){
+void jtag430_handle_fn(uint8_t const app,
+ uint8_t const verb,
+ uint32_t const len)
+{
+ unsigned long at, l;
+ unsigned int i, val;
+
+
+ /* FIXME
+ * Sometimes JTAG doesn't init correctly.
+ * This restarts the connection if the masked-rom
+ * chip ID cannot be read. Should print warning
+ * for testing server.
+ */
+ if (jtagid!=0)
+ while((i=jtag430_readmem(0xff0))==0xFFFF){
+ debugstr("Reconnecting to target MSP430.");
+ jtag430x2_start();
+ led_toggle();
+ }
+ led_off();
+
switch(verb){
case START:
- //Enter JTAG mode.
- jtag430_start();
- //TAP setup, fuse check
+ debugstr("Using JTAG430 (instead of JTAG430X2)!");
+
+ jtag430x2_start();
+ cmddata[0]=jtagid;
+
+ jtag430mode=MSP430MODE;
+
+ /* So the way this works is that a width of 20 does some
+ backward-compatibility finagling, causing the correct value
+ to be exchanged for addresses on 16-bit chips as well as the
+ new MSP430X chips. (This has only been verified on the
+ MSP430F2xx family. TODO verify for others.)
+ */
+
+ drwidth=20;
+
+ //Perform a reset and disable watchdog.
+ jtag430_por();
+ jtag430_writemem(0x120,0x5a80);//disable watchdog
+
+ jtag430_haltcpu();
+
jtag430_resettap();
+ txdata(app,verb,1);
+
+ break;
+ case STOP:
+ jtag430_stop();
txdata(app,verb,0);
break;
case JTAG430_HALTCPU:
case JTAG430_READMEM:
case PEEK:
- cmddataword[0]=jtag430_readmem(cmddataword[0]);
- txdata(app,verb,2);
+ at=cmddatalong[0];
+
+ //Fetch large blocks for bulk fetches,
+ //small blocks for individual peeks.
+ if(len>5)
+ l=(cmddataword[2]);//always even.
+ else
+ l=2;
+ l&=~1;//clear lsbit
+
+ txhead(app,verb,l);
+ for(i = 0; i < l; i += 2) {
+ jtag430_resettap();
+ val=jtag430_readmem(at);
+
+ at+=2;
+ serial_tx(val&0xFF);
+ serial_tx((val&0xFF00)>>8);
+ }
break;
case JTAG430_WRITEMEM:
case POKE:
- jtag430_writemem(cmddatalong[0],cmddataword[2]);
- cmddataword[0]=jtag430_readmem(cmddatalong[0]);
+ jtag430_haltcpu();
+ jtag430_writemem(cmddataword[0],cmddataword[2]);
+ cmddataword[0]=jtag430_readmem(cmddataword[0]);
txdata(app,verb,2);
break;
case JTAG430_WRITEFLASH:
- jtag430_writeflash(cmddataword[0],cmddataword[1]);
+ at=cmddataword[0];
+
+ for(i=0;i<(len>>1)-2;i++){
+ //debugstr("Poking flash memory.");
+ jtag430_writeflash(at+(i<<1),cmddataword[i+2]);
+ //Reflash if needed. Try this twice to save grace?
+ if(cmddataword[i]!=jtag430_readmem(at))
+ jtag430_writeflash(at+(i<<1),cmddataword[i+2]);
+ }
+
+ //Return result of first write as a word.
cmddataword[0]=jtag430_readmem(cmddataword[0]);
+
txdata(app,verb,2);
break;
case JTAG430_ERASEFLASH:
- jtag430_eraseflash(ERASE_MASS,0xFFFE,0xFFFF);
- jtag430_eraseflash(ERASE_MASS,0xFFFE,0xFFFF);
- jtag430_eraseflash(ERASE_MASS,0xFFFE,0xFFFF);
+ jtag430_eraseflash(ERASE_MASS,0xFFFE,0x3000,0);
+ txdata(app,verb,0);
+ break;
+ case JTAG430_ERASEINFO:
+ jtag430_eraseflash(ERASE_SGMT,0x1000,0x3000,1);
txdata(app,verb,0);
break;
case JTAG430_SETPC:
+ jtag430_haltcpu();
+ //debughex("Setting PC.");
+ //debughex(cmddataword[0]);
jtag430_setpc(cmddataword[0]);
+ jtag430_releasecpu();
txdata(app,verb,0);
break;
+ case JTAG430_SETREG:
+ jtag430_setr(cmddata[0],cmddataword[1]);
+ txdata(app,verb,0);
+ break;
+ case JTAG430_GETREG:
+ //jtag430_getr(cmddata[0]);
+ debugstr("JTAG430_GETREG not yet implemented.");
+ cmddataword[0]=0xDEAD;
+ txdata(app,verb,2);
+ break;
+ case JTAG430_COREIP_ID:
+ //cmddataword[0]=jtag430_coreid();
+ cmddataword[0]=0xdead;
+ txdata(app,verb,2);
+ break;
+ case JTAG430_DEVICE_ID:
+ //cmddatalong[0]=jtag430_deviceid();
+ cmddataword[0]=0xdead;
+ cmddataword[1]=0xbeef;
+ txdata(app,verb,4);
+ break;
default:
- jtaghandle(app,verb,len);
- }
- jtag430_resettap();
-}
-
-//! Handles unique MSP430 JTAG commands. Forwards others to JTAG.
-void jtag430handle(unsigned char app,
- unsigned char verb,
- unsigned char len){
- switch(jtag430mode){
- case MSP430MODE:
- return oldjtag430handle(app,verb,len);
- case MSP430X2MODE:
- return jtag430x2handle(app,verb,len);
- default:
- txdata(app,NOK,0);
+ (*(jtag_app.handle))(app,verb,len);
}
+ //jtag430_resettap(); //DO NOT UNCOMMENT
}
projects / goodfet / blobdiff