Beginnings of info flash support. It isn't very good.

[goodfet] / firmware / apps / jtag / jtag430.c

diff --git a/firmware/apps/jtag/jtag430.c b/firmware/apps/jtag/jtag430.c
index 22687da..d704e86 100644 (file)
--- a/firmware/apps/jtag/jtag430.c
+++ b/firmware/apps/jtag/jtag430.c
@@ -70,7 +70,7 @@ unsigned int jtag430_readmem(unsigned int adr){
   else
     jtag_dr_shift16(0x2419);//byte read
   jtag_ir_shift8(IR_ADDR_16BIT);
-  jtag_dr_shift16(adr);//address
+  jtag_dr_shiftadr(adr);//address
   jtag_ir_shift8(IR_DATA_TO_ADDR);
   SETTCLK;
 
@@ -89,7 +89,7 @@ void jtag430_writemem(unsigned int adr, unsigned int data){
   else
     jtag_dr_shift16(0x2418);//byte write
   jtag_ir_shift8(IR_ADDR_16BIT);
-  jtag_dr_shift16(adr);
+  jtag_dr_shiftadr(adr);
   jtag_ir_shift8(IR_DATA_TO_ADDR);
   jtag_dr_shift16(data);
   SETTCLK;
@@ -102,7 +102,7 @@ void jtag430_writeflashword(unsigned int adr, unsigned int data){
   jtag_ir_shift8(IR_CNTRL_SIG_16BIT);
   jtag_dr_shift16(0x2408);//word write
   jtag_ir_shift8(IR_ADDR_16BIT);
-  jtag_dr_shift16(adr);
+  jtag_dr_shiftadr(adr);
   jtag_ir_shift8(IR_DATA_TO_ADDR);
   jtag_dr_shift16(data);
   SETTCLK;
@@ -173,7 +173,8 @@ void jtag430_por(){
 #define ERASE_SGMT 0xA502
 
 //! Configure flash, then write a word.
-void jtag430_eraseflash(unsigned int mode, unsigned int adr, unsigned int count){
+void jtag430_eraseflash(unsigned int mode, unsigned int adr, unsigned int count,
+                       unsigned int info){
   jtag430_haltcpu();
   
   //FCTL1= erase mode
@@ -181,7 +182,10 @@ void jtag430_eraseflash(unsigned int mode, unsigned int adr, unsigned int count)
   //FCTL2=0xA540, selecting MCLK as source, DIV=1
   jtag430_writemem(0x012A, 0xA540);
   //FCTL3=0xA500, should be 0xA540 for Info Seg A on 2xx chips.
-  jtag430_writemem(0x012C, 0xA500);
+  if(info)
+    jtag430_writemem(0x012C, 0xA540);
+  else
+    jtag430_writemem(0x012C, 0xA500);
   
   //Write the erase word.
   jtag430_writemem(adr, 0x55AA);
@@ -245,6 +249,7 @@ void jtag430_start(){
   SETRST;
   delay(0xFFFF);
 
+
   #ifndef SBWREWRITE
   //Entry sequence from Page 67 of SLAU265A for 4-wire MSP430 JTAG
   CLRRST;
@@ -265,7 +270,7 @@ void jtag430_start(){
   jtag430_haltcpu();
 }
 
-//! Start normally, not JTAG.
+//! Stop JTAG.
 void jtag430_stop(){
   debugstr("Exiting JTAG.");
   jtagsetup();
@@ -322,7 +327,8 @@ void jtag430handle(unsigned char app,
     P1OUT^=1;
   }
   P1OUT&=~1;
-    
+  
+  
   switch(verb){
   case START:
     //Enter JTAG mode.
@@ -412,7 +418,11 @@ void jtag430handle(unsigned char app,
     txdata(app,verb,2);
     break;
   case JTAG430_ERASEFLASH:
-    jtag430_eraseflash(ERASE_MASS,0xFFFE,0x3000);
+    jtag430_eraseflash(ERASE_MASS,0xFFFE,0x3000,0);
+    txdata(app,verb,0);
+    break;
+  case JTAG430_ERASEINFO:
+    jtag430_eraseflash(ERASE_MASS,0xFFFE,0x3000,1);
     txdata(app,verb,0);
     break;
   case JTAG430_SETPC: