//! Handles a Chipcon SPI command.
void ccspi_handle_fn( uint8_t const app,
- uint8_t const verb,
- uint32_t const len);
+ uint8_t const verb,
+ uint32_t const len);
// define the ccspi app's app_t
app_t const ccspi_app = {
}
+//! Reflexively jam on the present channel.
+void ccspireflexjam(u16 delay){
+ unsigned long i;
+ #if defined(FIFOP) && defined(SFD) && defined(FIFO) && defined(PLED2DIR) && defined(PLED2PIN) && defined(PLED2OUT)
+
+ prep_timer();
+ debugstr("Reflex jamming until reset.");
+ debughex(delay);
+ txdata(CCSPI,CCSPI_REFLEX,1); //Let the client continue its business.
+ while(1) {
+ //Wait until a packet is received
+ while(!SFD){
+ //Has there been an overflow in the RX buffer?
+ if((!FIFO)&&FIFOP){
+ //debugstr("Clearing RX overflow");
+ CLRSS;
+ ccspitrans8(0x08); //SFLUSHRX
+ SETSS;
+ }
+ }
+ //Turn on LED 2 (green) as signal
+ PLED2DIR |= PLED2PIN;
+ PLED2OUT &= ~PLED2PIN;
+
+
+
+ //Wait a few us to send it.
+ delay_us(delay);
+
+ //Transmit the packet.
+ CLRSS;
+ ccspitrans8(0x04);
+ SETSS;
+
+
+ //Load the next jamming packet.
+ //Note: attempts to preload this actually slowed the jam time down from 7 to 9 bytes.
+ CLRSS;
+ ccspitrans8(CCSPI_TXFIFO);
+ char pkt[5] = {0x05, 0, 0, 0, 0};
+ //char pkt[15] = {0x0f, 0x01, 0x08, 0x82, 0xff, 0xff, 0xff, 0xff, 0xde, 0xad, 0xbe, 0xef, 0xba, 0xbe, 0xc0};
+ //char pkt[12] = {0x0c, 0x01, 0x08, 0x82, 0xff, 0xff, 0xff, 0xff, 0xde, 0xad, 0xbe, 0xef};
+ for(i=0;i<pkt[0];i++)
+ ccspitrans8(pkt[i]);
+ SETSS;
+
+ //* I think this might be unnecessary.
+ //msdelay(100+delay); //Instead of waiting for pulse on SFD
+ //delay_ms(1);
+ //Flush TX buffer.
+ CLRSS;
+ ccspitrans8(0x09); //SFLUSHTX
+ SETSS;
+
+
+ //Turn off LED 2 (green) as signal
+ PLED2DIR |= PLED2PIN;
+ PLED2OUT |= PLED2PIN;
+ }
+#else
+ debugstr("Can't reflexively jam without SFD, FIFO, FIFOP, and P2LEDx definitions - try using telosb platform.");
+ txdata(CCSPI,NOK,0);
+#endif
+}
+
+
+
//! Writes a register
u8 ccspi_regwrite(u8 reg, const u8 *buf, int len){
CLRSS;
uint8_t const verb,
uint32_t const len){
unsigned long i;
+ u8 j;
//debugstr("Chipcon SPI handler.");
case WRITE:
case POKE:
CLRSS; //Drop !SS to begin transaction.
+ j=cmddata[0];//Backup address.
for(i=0;i<len;i++)
cmddata[i]=ccspitrans8(cmddata[i]);
SETSS; //Raise !SS to end transaction.
+ cmddata[0]=j&~0x40;//Restore address.
txdata(app,verb,len);
break;
case SETUP:
SETSS;
//Flush buffer.
- //CLRSS;
- //ccspitrans8(0x08); //SFLUSHRX
- //SETSS;
+ CLRSS;
+ ccspitrans8(0x08); //SFLUSHRX
+ SETSS;
//Only should transmit length of one more than the reported
break;
case CCSPI_REFLEX:
-#if defined(FIFOP) && defined(SFD) && defined(FIFO) && defined(PLED2DIR) && defined(PLED2PIN) && defined(PLED2OUT)
- txdata(app,verb,1); //Just sending some response back to client
- while(1) {
- //Wait until a packet is received
- while(!SFD);
- //Turn on LED 2 (green) as signal
- PLED2DIR |= PLED2PIN;
- PLED2OUT &= ~PLED2PIN;
-
- //Put radio in TX mode
- CLRSS;
- ccspitrans8(0x04);
- SETSS;
-
- //Load the jamming packet.
- //Note: attempts to preload this actually slowed the jam time down from 7 to 9 bytes.
- CLRSS;
- ccspitrans8(CCSPI_TXFIFO);
- char pkt[15] = {0x0f, 0x01, 0x08, 0x82, 0xff, 0xff, 0xff, 0xff, 0xde, 0xad, 0xbe, 0xef, 0xba, 0xbe, 0xc0};
- //char pkt[12] = {0x0c, 0x01, 0x08, 0x82, 0xff, 0xff, 0xff, 0xff, 0xde, 0xad, 0xbe, 0xef};
- for(i=0;i<pkt[0];i++)
- ccspitrans8(pkt[i]);
- SETSS;
-
- //Transmit the packet.
- CLRSS;
- ccspitrans8(0x04); //STXON
- SETSS;
- msdelay(100); //Instead of waiting for pulse on SFD
- //Flush TX buffer.
- CLRSS;
- ccspitrans8(0x09); //SFLUSHTX
- SETSS;
-
- //Turn off LED 2 (green) as signal
- PLED2DIR |= PLED2PIN;
- PLED2OUT |= PLED2PIN;
- }
- //TODO the firmware stops staying in this mode after a while, and stops jamming... need to find a fix.
+ ccspireflexjam(len?cmddataword[0]:0);
break;
-#else
- debugstr("Can't reflexively jam without SFD, FIFO, FIFOP, and P2LEDx definitions - try using telosb platform.");
- txdata(app,NOK,0);
-#endif
case CCSPI_REFLEX_AUTOACK:
#if defined(FIFOP) && defined(SFD) && defined(FIFO) && defined(PLED2DIR) && defined(PLED2PIN) && defined(PLED2OUT)
//Wait for last packet to TX.
//while(ccspi_status()&BIT3);
+
+ //Flush TX buffer.
+ CLRSS;
+ ccspitrans8(0x09); //SFLUSHTX
+ SETSS;
+
//Load the packet.
CLRSS;
//Wait for the pulse on SFD, after which the packet has been sent.
while(!SFD);
while(SFD);
-
- //Flush TX buffer.
- CLRSS;
- ccspitrans8(0x09); //SFLUSHTX
- SETSS;
-
+
txdata(app,verb,0);
#else
debugstr("Can't TX a packet with SFD and FIFOP definitions.");