//Higher level left to client application.
-#include "platform.h"
+
#include "command.h"
+#ifdef __MSPGCC__
+#include <msp430.h>
+#else
#include <signal.h>
#include <io.h>
#include <iomacros.h>
+#endif
#include "spi.h"
+#define SPIAPPLICATION
+
+#include "platform.h"
+
//! Handles a monitor command.
void spi_handle_fn( uint8_t const app,
uint8_t const verb,
//! Set up the pins for SPI mode.
void spisetup(){
SETSS;
- P5DIR|=MOSI+SCK+BIT0; //BIT0 might be SS
- P5DIR&=~MISO;
+ SPIDIR|=MOSI+SCK+BIT0; //BIT0 might be SS
+ SPIDIR&=~MISO;
DIRSS;
-
+
//Begin a new transaction.
-
- CLRSS;
+
+ CLRSS;
SETSS;
-
}
register unsigned int bit;
//This function came from the SPI Wikipedia article.
//Minor alterations.
-
+
for (bit = 0; bit < 8; bit++) {
/* write MOSI on trailing edge of previous clock */
if (byte & 0x80)
else
CLRMOSI;
byte <<= 1;
-
+
//SPIDELAY(100);
SETCLK;
//SPIDELAY(100);
-
+
/* read MISO on trailing edge */
byte |= READMISO;
CLRCLK;
unsigned char *buf,
unsigned int len){
unsigned char i;
-
+
SETSS;
CLRSS; //Drop !SS to begin transaction.
spitrans8(0x03);//Flash Read Command
-
+
//Send address
spitrans8((adr&0xFF0000)>>16);
spitrans8((adr&0xFF00)>>8);
spitrans8(adr&0xFF);
-
+
for(i=0;i<len;i++)
buf[i]=spitrans8(0);
SETSS; //Raise !SS to end transaction.
unsigned char *buf,
unsigned int len){
unsigned int i;
-
+
SETSS;
-
+
//if(len!=0x100)
// debugstr("Non-standard block size.");
-
+
while(spiflash_status()&0x01);//minor performance impact
-
+
spiflash_setstatus(0x02);
spiflash_wrten();
-
+
//Are these necessary?
//spiflash_setstatus(0x02);
//spiflash_wrten();
-
+
CLRSS; //Drop !SS to begin transaction.
spitrans8(0x02); //Poke command.
-
+
//Send address
spitrans8((adr&0xFF0000)>>16);
spitrans8((adr&0xFF00)>>8);
for(i=0;i<len;i++)
spitrans8(buf[i]);
SETSS; //Raise !SS to end transaction.
-
+
while(spiflash_status()&0x01);//minor performance impact
return;
}
long off=0;//offset of this block
int blen;//length of this block
SETSS;
-
+
while(off<len){
//calculate block length
blen=(len-off>0x100?0x100:len-off);
len=3;//write 3 byte pointer
for(i=0;i<len;i++)
spitrans8(cmddata[i]);
-
+
//Send reply header
len=0x1000;
txhead(app,verb,len);
-
+
while(len--)
serial_tx(spitrans8(0));
-
+
SETSS; //Raise !SS to end transaction.
}
P2DIR|=RST;
SETRST;
delay(1024);
-
+
CLRRST;//Wake chip.
while(P4IN&1);
SETRST;//Woken.
void spi_rw_em260(u8 app, u8 verb, u32 len){
unsigned long i;
u8 lastin;
-
+
P4DIR=0; //TODO ASAP remove P4 references.
P4OUT=0xFF;
//P4REN=0xFF;
-
+
//See GoodFETEM260.py for details.
//The EM260 requires that the host wait for the client.
-
+
/*
if((~P4IN)&1)
debugstr("Detected HOST_INT.");
*/
-
+
em260_wake();
-
-
+
+
SETMOSI; //Autodetected SPI mode.
CLRSS; //Drop !SS to begin transaction.
//Host to slave. Ignore data.
}
}
//debugstr("Finished transmission to EM260.");
-
+
//Wait for nHOST_INT to drop.
i=0xffff;
-
+
/*
while(P4IN&1
&& --i
*/
while((cmddata[0]=spitrans8(0xFF))==0xFF
&& --i);
-
+
if(!i)
debugstr("Gave up on host interrupt.");
-
+
response:
len=1;
while(
while(len<cmddata[1]+3)
cmddata[len++]=spitrans8(0xFF);
SETSS; //Raise !SS to end transaction.
-
+
txdata(app,verb,len);
return;
}
case POKE://Poke up bytes from an SPI Flash ROM.
spiflash_pokeblocks(cmddatalong[0],//adr
cmddata+4,//buf
- len-4);//len
+ len-4);//len
txdata(app,verb,0);
break;
SETSS; //Raise !SS to end transaction.
while(spiflash_status()&0x01)//while busy
- PLEDOUT^=PLEDPIN;
- PLEDOUT&=~PLEDPIN;
+ led_toggle();
+ led_off();
txdata(app,verb,0);
break;