#include <io.h>
#include <iomacros.h>
-
//! Receive a byte.
-unsigned char serial_rx(){
+unsigned char serial0_rx(){
char c;
while(!(IFG1&URXIFG0));//wait for a byte
return c;
}
-
//! Transmit a byte.
-void serial_tx(unsigned char x){
+void serial0_tx(unsigned char x){
while ((IFG1 & UTXIFG0) == 0); //loop until buffer is free
TXBUF0 = x;
}
TXBUF1 = x;
}
+/** Later, add support for the EZ430/FETUIF with 12MHz crystal
+ UBR00=0xE2; UBR10=0x04; UMCTL0=0x00; // uart0 12000000Hz 9600bps
+ UBR00=0x71; UBR10=0x02; UMCTL0=0x00; // uart0 12000000Hz 19200bps
+ UBR00=0x38; UBR10=0x01; UMCTL0=0x55; // uart0 12000000Hz 38400bps
+ UBR00=0xD0; UBR10=0x00; UMCTL0=0x4A; // uart0 12000000Hz 57581bps
+ UBR00=0x68; UBR10=0x00; UMCTL0=0x04; // uart0 12000000Hz 115273bps
+ */
+
//! Set the baud rate.
-void setbaud(unsigned char rate){
+void setbaud0(unsigned char rate){
//http://mspgcc.sourceforge.net/baudrate.html
switch(rate){
//! Set the baud rate of the second uart.
void setbaud1(unsigned char rate){
-
//http://mspgcc.sourceforge.net/baudrate.html
switch(rate){
case 1://9600 baud
- // UBR01=0x7F; UBR11=0x01; UMCTL1=0x5B; /* uart0 3683400Hz 9599bps */
+ UBR01=0x7F; UBR11=0x01; UMCTL1=0x5B; /* uart0 3683400Hz 9599bps */
break;
case 2://19200 baud
- //UBR01=0xBF; UBR11=0x00; UMCTL1=0xF7; /* uart0 3683400Hz 19194bps */
+ UBR01=0xBF; UBR11=0x00; UMCTL1=0xF7; /* uart0 3683400Hz 19194bps */
break;
case 3://38400 baud
- //UBR01=0x5F; UBR11=0x00; UMCTL1=0xBF; /* uart0 3683400Hz 38408bps */
+ UBR01=0x5F; UBR11=0x00; UMCTL1=0xBF; /* uart0 3683400Hz 38408bps */
break;
case 4://57600 baud
- //UBR01=0x40; UBR11=0x00; UMCTL1=0x00; /* uart0 3683400Hz 57553bps */
+ UBR01=0x40; UBR11=0x00; UMCTL1=0x00; /* uart0 3683400Hz 57553bps */
break;
default:
case 5://115200 baud
- //UBR01=0x20; UBR11=0x00; UMCTL1=0x00; /* uart0 3683400Hz 115106bps */
+ UBR01=0x20; UBR11=0x00; UMCTL1=0x00; /* uart0 3683400Hz 115106bps */
break;
}
}
-void msp430_init_uart(){
+void msp430_init_uart0(){
+ /* RS232 */
+
+ P3SEL |= BIT4|BIT5; // P3.4,5 = USART0 TXD/RXD
+ P3DIR |= BIT4;
+
+ UCTL0 = SWRST | CHAR; /* 8-bit character, UART mode */
+ UTCTL0 = SSEL1; /* UCLK = MCLK */
+
+ setbaud0(0);
+
+ ME1 &= ~USPIE0; /* USART1 SPI module disable */
+ ME1 |= (UTXE0 | URXE0); /* Enable USART1 TXD/RXD */
+
+ UCTL0 &= ~SWRST;
+
+ /* XXX Clear pending interrupts before enable!!! */
+ U0TCTL |= URXSE;
+
+
+ //IE1 |= URXIE1; /* Enable USART1 RX interrupt */
+}
+
+
+void msp430_init_uart1(){
+
+ /* RS232 */
+ P3DIR &= ~0x80; /* Select P37 for input (UART1RX) */
+ P3DIR |= 0x40; /* Select P36 for output (UART1TX) */
+ P3SEL |= 0xC0; /* Select P36,P37 for UART1{TX,RX} */
+
+ UCTL1 = SWRST | CHAR; /* 8-bit character, UART mode */
+ UTCTL1 = SSEL1; /* UCLK = MCLK */
+
+ setbaud1(0);
+
+ ME2 &= ~USPIE1; /* USART1 SPI module disable */
+ ME2 |= (UTXE1 | URXE1); /* Enable USART1 TXD/RXD */
+
+ UCTL1 &= ~SWRST;
+
+ /* XXX Clear pending interrupts before enable!!! */
+ U1TCTL |= URXSE;
+
+ //IE2 |= URXIE1; /* Enable USART1 RX interrupt */
+}
+
+
+/** For EZ430/FETUIF
+ void msp430_init_dco() {
+ WDTCTL = WDTPW + WDTHOLD; //stop WDT
+
+ BCSCTL1 = 0;
+
+ do {
+ int i;
+ IFG1 &= ~OFIFG;
+ for (i=0; i<1000; i++);
+
+ } while (IFG1 & OFIFG);
+
+ BCSCTL2 = SELM1 | DIVM1 | SELS;
+
+}
+ */
+
+
+//! Initialization is correct.
+void msp430_init_dco_done(){
+ //Nothing to do for the 1612.
}
void msp430_init_dco() {
+/* This code taken from the FU Berlin sources and reformatted. */
+ //
+
+//Works well.
+//#define MSP430_CPU_SPEED 2457600UL
+
+//Too fast for internal resistor.
+//#define MSP430_CPU_SPEED 4915200UL
+
+//Max speed.
+//#define MSP430_CPU_SPEED 4500000UL
+
+//baud rate speed
+#define MSP430_CPU_SPEED 3683400UL
+#define DELTA ((MSP430_CPU_SPEED) / (32768 / 8))
+ unsigned int compare, oldcapture = 0;
+ unsigned int i;
+
+ WDTCTL = WDTPW + WDTHOLD; //stop WDT
+
+
+ DCOCTL=0xF0;
+ //a4
+ //1100
+
+ /* ACLK is devided by 4. RSEL=6 no division for MCLK
+ and SSMCLK. XT2 is off. */
+ //BCSCTL1 = 0xa8;
+
+ BCSCTL2 = 0x00; /* Init FLL to desired frequency using the 32762Hz
+ crystal DCO frquenzy = 2,4576 MHz */
+
+ PLEDOUT|=PLEDPIN;
+
+ BCSCTL1 |= DIVA1 + DIVA0; /* ACLK = LFXT1CLK/8 */
+ for(i = 0xffff; i > 0; i--) { /* Delay for XTAL to settle */
+ asm("nop");
+ }
+
+ CCTL2 = CCIS0 + CM0 + CAP; // Define CCR2, CAP, ACLK
+ TACTL = TASSEL1 + TACLR + MC1; // SMCLK, continous mode
+
+
+ while(1) {
+
+ while((CCTL2 & CCIFG) != CCIFG); /* Wait until capture occured! */
+ CCTL2 &= ~CCIFG; /* Capture occured, clear flag */
+ compare = CCR2; /* Get current captured SMCLK */
+ compare = compare - oldcapture; /* SMCLK difference */
+ oldcapture = CCR2; /* Save current captured SMCLK */
+
+ if(DELTA == compare) {
+ break; /* if equal, leave "while(1)" */
+ } else if(DELTA < compare) { /* DCO is too fast, slow it down */
+ DCOCTL--;
+ if(DCOCTL == 0xFF) { /* Did DCO role under? */
+ BCSCTL1--;
+ }
+ } else { /* -> Select next lower RSEL */
+ DCOCTL++;
+ if(DCOCTL == 0x00) { /* Did DCO role over? */
+ BCSCTL1++;
+ }
+ /* -> Select next higher RSEL */
+ }
+ }
+
+ CCTL2 = 0; /* Stop CCR2 function */
+ TACTL = 0; /* Stop Timer_A */
+
+ BCSCTL1 &= ~(DIVA1 + DIVA0); /* remove /8 divisor from ACLK again */
+
+ PLEDOUT=0;
+
}
projects / goodfet / blobdiff