+++ /dev/null
-//! MSP430F2618 clock and I/O definitions
-
-// Included by other 2xx ports, such as the 2274.
-
-#include "platform.h"
-
-#include "dco_calib.h"
-#ifdef __MSPGCC__
-#include <msp430.h>
-#else
-#include <signal.h>
-#include <io.h>
-#include <iomacros.h>
-#endif
-
-
-//! Receive a byte.
-unsigned char serial0_rx(){
- char c;
-
- while(!(IFG2&UCA0RXIFG));//wait for a byte
- c = UCA0RXBUF;
- IFG2&=~UCA0RXIFG;
-
- //UCA0CTL1 &= ~UCA0RXSE;
- return c;
-}
-
-//! Receive a byte.
-unsigned char serial1_rx(){
- //TODO
- return 00;
-}
-
-//! Transmit a byte.
-void serial0_tx(unsigned char x){
- while ((IFG2 & UCA0TXIFG) == 0); //loop until buffer is free
- UCA0TXBUF = x; /* send the character */
- while(!(IFG2 & UCA0TXIFG));
-}
-//! Transmit a byte.
-void serial_tx_old(unsigned char x){
- while ((IFG2 & UCA0TXIFG) == 0); //loop until buffer is free
- UCA0TXBUF = x; /* send the character */
- while(!(IFG2 & UCA0TXIFG));
-}
-
-//! Transmit a byte on the second UART.
-void serial1_tx(unsigned char x){
-
-}
-
-//! Set the baud rate.
-void setbaud0(unsigned char rate){
-
- //Table 15-4, page 481 of 2xx Family Guide
- switch(rate){
- case 1://9600 baud
- UCA0BR1 = 0x06;
- UCA0BR0 = 0x82;
- break;
- case 2://19200 baud
- UCA0BR1 = 0x03;
- UCA0BR0 = 0x41;
- break;
- case 3://38400 baud
- UCA0BR1 = 0xa0;
- UCA0BR0 = 0x01;
- break;
- case 4://57600 baud
- UCA0BR1 = 0x1d;
- UCA0BR0 = 0x01;
- break;
- default:
- case 5://115200 baud
- UCA0BR0 = 0x8a;
- UCA0BR1 = 0x00;
- break;
- }
-}
-
-//! Set the baud rate of the second uart.
-void setbaud1(unsigned char rate){
-
-}
-
-#define BAUD0EN 0x41
-#define BAUD1EN 0x03
-
-void msp430_init_uart(){
-
- // Serial on P3.4, P3.5
- P3SEL |= BIT4 + BIT5;
- P3DIR |= BIT4;
-
- //UCA0CTL1 |= UCSWRST; /* disable UART */
-
- UCA0CTL0 = 0x00;
- //UCA0CTL0 |= UCMSB ;
-
- UCA0CTL1 |= UCSSEL_2; // SMCLK
-
- //UCA0BR0 = BAUD0EN; // 115200
- //UCA0BR1 = BAUD1EN;
- setbaud(5);//default baud, 115200
-
- UCA0MCTL = 0; // Modulation UCBRSx = 5
- UCA0CTL1 &= ~UCSWRST; // **Initialize USCI state machine**
-
-
- //Leave this commented!
- //Interrupt is handled by target code, not by bootloader.
- //IE2 |= UCA0RXIE;
-}
-
-
-//! Initialization is correct.
-void msp430_init_dco_done(){
- char *choice=(char *) 0x200; //First word of RAM.
- choice[0]--;
-}
-
-//! Initialize the MSP430 clock.
-void msp430_init_dco() {
- int i=1000;
- char *choice=(char *) 0x200; //First word of RAM.
-
- #ifdef __MSP430_HAS_PORT8__
- P8SEL = 0; // disable XT2 on P8.7/8
- #endif
-
- //Set P2.6 mode for MSP430F2274
- #ifndef __MSP430_HAS_PORT5__
- P2SEL = 0; //disable XIN on 2274
- #endif
-
-
- #ifdef STATICDCO
- BCSCTL1 = (STATICDCO>>8);
- DCOCTL = (STATICDCO&0xFF);
- #else
- if(CALBC1_16MHZ!=0xFF){
- //Info is intact, use it.
- BCSCTL1 = CALBC1_16MHZ;
- DCOCTL = CALDCO_16MHZ;
- }else{
- /*
- Info is missing, guess at a good value.
-
- A list of correct calibrations in included as dco_calib.c,
- generated by script.
- */
- DCOCTL = 0x00; //clear DCO
-
- BCSCTL1 = dco_calibrations[2*choice[0]+1];
- DCOCTL = dco_calibrations[2*choice[0]];
- choice[0]++;
- choice[0]%=dco_calibrations_count;
- }
- #endif
-
- //Minor delay.
- while(i--);
-
-
-
- return;
-}
-