Added support for uniarch mspgcc4

[goodfet] / firmware / lib / msp430x2618.c

diff --git a/firmware/lib/msp430x2618.c b/firmware/lib/msp430x2618.c
index 947cf14..408e3ee 100644 (file)
--- a/firmware/lib/msp430x2618.c
+++ b/firmware/lib/msp430x2618.c
@@ -5,19 +5,23 @@
 #include "platform.h"
 
 #include "dco_calib.h"
-
+#ifdef __MSPGCC__
+#include <msp430.h>
+#else
 #include <signal.h>
 #include <io.h>
 #include <iomacros.h>
+#endif
+
 
 //! Receive a byte.
 unsigned char serial0_rx(){
   char c;
-  
+
   while(!(IFG2&UCA0RXIFG));//wait for a byte
   c = UCA0RXBUF;
   IFG2&=~UCA0RXIFG;
-  
+
   //UCA0CTL1 &= ~UCA0RXSE;
   return c;
 }
@@ -48,7 +52,7 @@ void serial1_tx(unsigned char x){
 
 //! Set the baud rate.
 void setbaud0(unsigned char rate){
-  
+
   //Table 15-4, page 481 of 2xx Family Guide
   switch(rate){
   case 1://9600 baud
@@ -77,33 +81,33 @@ void setbaud0(unsigned char rate){
 
 //! Set the baud rate of the second uart.
 void setbaud1(unsigned char rate){
-  
+
 }
 
 #define BAUD0EN 0x41
 #define BAUD1EN 0x03
 
 void msp430_init_uart(){
-  
+
   // Serial on P3.4, P3.5
   P3SEL |= BIT4 + BIT5;
   P3DIR |= BIT4;
-  
+
   //UCA0CTL1 |= UCSWRST;                    /* disable UART */
-  
+
   UCA0CTL0 = 0x00;
   //UCA0CTL0 |= UCMSB ;
-  
+
   UCA0CTL1 |= UCSSEL_2;                     // SMCLK
-  
+
   //UCA0BR0 = BAUD0EN;                        // 115200
   //UCA0BR1 = BAUD1EN;
   setbaud(5);//default baud, 115200
-  
+
   UCA0MCTL = 0;                             // Modulation UCBRSx = 5
   UCA0CTL1 &= ~UCSWRST;                     // **Initialize USCI state machine**
-  
-  
+
+
   //Leave this commented!
   //Interrupt is handled by target code, not by bootloader.
   //IE2 |= UCA0RXIE;
@@ -120,17 +124,17 @@ void msp430_init_dco_done(){
 void msp430_init_dco() {
   int i=1000;
   char *choice=(char *) 0x200; //First word of RAM.
-  
+
   #ifdef __MSP430_HAS_PORT8__
   P8SEL = 0; // disable XT2 on P8.7/8
   #endif
-  
+
   //Set P2.6 mode for MSP430F2274
   #ifndef __MSP430_HAS_PORT5__
   P2SEL = 0; //disable XIN on 2274
   #endif
-  
-  
+
+
   #ifdef STATICDCO
   BCSCTL1 = (STATICDCO>>8);
   DCOCTL  = (STATICDCO&0xFF);
@@ -142,24 +146,24 @@ void msp430_init_dco() {
   }else{
     /*
       Info is missing, guess at a good value.
-      
+
       A list of correct calibrations in included as dco_calib.c,
       generated by script.
     */
     DCOCTL = 0x00; //clear DCO
-    
+
     BCSCTL1 =  dco_calibrations[2*choice[0]+1];
     DCOCTL  =  dco_calibrations[2*choice[0]];
     choice[0]++;
     choice[0]%=dco_calibrations_count;
   }
   #endif
-  
+
   //Minor delay.
   while(i--);
-  
-  
-  
+
+
+
   return;
 }