X-Git-Url: http://git.rot13.org/?p=goodfet;a=blobdiff_plain;f=client%2Fgoodfet.nrf;h=b7f7927f8505e9ffb042965772d9452be7d41f5d;hp=117a272d4dff9abc0581dc73abc09714f9441a50;hb=a4a0d6f5ac4e10d890a4a2e4ac2ee3caef810c69;hpb=7d033e4958693f8a618679d49eeae0ed735f996b

diff --git a/client/goodfet.nrf b/client/goodfet.nrf
index 117a272..b7f7927 100755
--- a/client/goodfet.nrf
+++ b/client/goodfet.nrf
@@ -11,6 +11,16 @@ import time;
 from GoodFETNRF import GoodFETNRF;
 from intelhex import IntelHex;
 
+
+regnames=["CONFIG","EN_AA","EN_RXADDR","SETUP_AW","SETUP_RET",
+          "RF_CH","RF_SETUP","STATUS","OBSERVE_TX","RPD",
+          "RX_ADDR_P0","RX_ADDR_P1","RX_ADDR_P2","RX_ADDR_P3","RX_ADDR_P4","RX_ADDR_P5",
+          "TX_ADDR",
+          "RX_PW_P0","RX_PW_P1","RX_PW_P2","RX_PW_P3","RX_PW_P4","RX_PW_P5",
+          "FIFO_STATUS","?",
+          "?","?","DYNPD","?","?","?","?","?",
+          "?","?","?","?","?","?","?","?"];
+
 def printpacket(packet):
     s="";
     i=0;
@@ -25,7 +35,7 @@ def printconfig():
     print "Freq    %10i MHz" % (client.RF_getfreq()/10**6);
     print "Rate    %10i kbps" % (client.RF_getrate()/1000);
     print "PacketLen %02i bytes" % client.RF_getpacketlen();
-    print "MacLen    %2i bytes" % client.RF_getmaclen();
+    #print "MacLen    %2i bytes" % client.RF_getmaclen();
     print "SMAC  0x%010x" % client.RF_getsmac();
     print "TMAC  0x%010x" % client.RF_gettmac();
 
@@ -35,6 +45,7 @@ if(len(sys.argv)==1):
     print "%s info" % sys.argv[0];
     print "%s test" % sys.argv[0];
     print "%s regs" % sys.argv[0];
+    print "%s pyregs" % sys.argv[0];
     print "%s sniff\n\tSniffs packets by current config." % sys.argv[0];
     print "%s sniffob\n\tSniffs OpenBeacon traffic." % sys.argv[0];
     print "%s carrier [freq]\n\tHolds a carrier on [freq] Hz." % sys.argv[0];
@@ -85,16 +96,11 @@ if(sys.argv[1]=="carrier"):
     while(1):
         time.sleep(1);
 if(sys.argv[1]=="regs"):
-    regnames=["CONFIG","EN_AA","EN_RXADDR","SETUP_AW","SETUP_RET",
-              "RF_CH","RF_SETUP","STATUS","OBSERVE_TX","RPD",
-              "RX_ADDR_P0","RX_ADDR_P1","RX_ADDR_P2","RX_ADDR_P3","RX_ADDR_P4","RX_ADDR_P5",
-              "TX_ADDR",
-              "RX_PW_P0","RX_PW_P1","RX_PW_P2","RX_PW_P3","RX_PW_P4","RX_PW_P5",
-              "FIFO_STATUS","?",
-              "?","?","DYNPD","?","?","?","?","?",
-              "?","?","?","?","?","?","?","?"];
     for r in range(0,0x20):
         print "r[0x%02x]=0x%010x //%16s " % (r,client.peek(r),regnames[r]);
+if(sys.argv[1]=="pyregs"):
+    for r in range(0,0x20):
+        print "client.set(0x%02x,0x%010x); #%16s " % (r,client.peek(r),regnames[r]);
 
 if(sys.argv[1]=="peek"):
     start=0x0000;
@@ -126,12 +132,13 @@ if(sys.argv[1]=="sniffob"):
     client.poke(0x00,0x00); #Stop nRF
     client.poke(0x01,0x00); #Disable Shockburst
     client.poke(0x02,0x01); #Set RX Pipe 0
-    client.RF_setmaclen(5); # SETUP_AW for 5-byte addresses.
+    
     client.RF_setfreq(2481 * 10**6);
     client.poke(0x06,0x09); #2MBps, -18dBm in RF_SETUP
     client.poke(0x07,0x78); #Reset status register
     
     #OpenBeacon defines these in little endian as follows.
+    client.RF_setmaclen(5); # SETUP_AW for 5-byte addresses.
     #0x01, 0x02, 0x03, 0x02, 0x01
     client.RF_setsmac(0x0102030201);
     #'O', 'C', 'A', 'E', 'B'
@@ -140,13 +147,12 @@ if(sys.argv[1]=="sniffob"):
     #Set packet length of 16.
     client.RF_setpacketlen(16);
     
-    #Power radio, prime for RX, checksum.
-    client.poke(0x00,0x70|0x03|0x08);
+    #Power radio, prime for RX, one-byte checksum.
+    client.poke(0x00,0x70|0x03|0x08); #0x08 for one byte, 0x04 for two.
     
     print "Listening as %010x on %i MHz" % (client.RF_getsmac(),
                                            client.RF_getfreq()/10**6);
     #Now we're ready to get packets.
-    
     while 1:
         packet=None;
         while packet==None:
@@ -173,3 +179,27 @@ if(sys.argv[1]=="sniff"):
             packet=client.RF_rxpacket();
         printpacket(packet);
         sys.stdout.flush();
+if(sys.argv[1]=="explore"):
+    #client.poke(0x00,0x00); #Stop nRF
+    client.poke(0x07,0x78); #Reset status register
+    
+    #Power radio, prime for RX, no checksum.
+    client.poke(0x00,0x70|0x03);
+    
+    #Set packet length of 32.
+    #Without checksums, extra data will mix in.
+    client.RF_setpacketlen(32);
+    client.RF_setmaclen(3); # shortest address length
+    
+    #Now we're ready to get packets.
+    for smac in [0x0102030201, 0]:
+        client.RF_setsmac(smac);
+        for chan in range(0,0x80):
+            client.RF_setfreq((2400+chan) * 10**6);
+            time.sleep(1);
+            packet=client.RF_rxpacket();
+            if packet!=None:
+                print "Listening as %010x on %i MHz" % (client.RF_getsmac(),
+                                                        client.RF_getfreq()/10**6);
+                printpacket(packet);
+                sys.stdout.flush();