X-Git-Url: http://git.rot13.org/?p=goodfet;a=blobdiff_plain;f=firmware%2Fapps%2Fchipcon%2Fchipcon.c;h=cf11b5a4e63921c54aa63f343b69c81a05a43b4b;hp=17905266428684aa3900b62851eba3fce574035d;hb=2f740ed7513a1db4c8a7b68f02347b783a4ca7ae;hpb=19289dc659d1dae658295be9a32f9b0dd4ed3034 diff --git a/firmware/apps/chipcon/chipcon.c b/firmware/apps/chipcon/chipcon.c index 1790526..cf11b5a 100644 --- a/firmware/apps/chipcon/chipcon.c +++ b/firmware/apps/chipcon/chipcon.c @@ -20,11 +20,11 @@ #include -/* Concerning clock rates, - the maximimum clock rates are defined on page 4 of the spec. - They vary, but are roughly 30MHz. Raising this clock rate might - allow for clock glitching, but the GoodFET isn't sufficient fast for that. - Perhaps a 200MHz ARM or an FPGA in the BadassFET? +/* Concerning clock rates, the maximimum clock rates are defined on + page 4 of the spec. They vary, but are roughly 30MHz. Raising + this clock rate might allow for clock glitching, but the GoodFET + isn't sufficient fast for that. Perhaps a 200MHz ARM or an FPGA in + the BadassFET? */ //Pins and I/O @@ -37,7 +37,8 @@ //This could be more accurate. //Does it ever need to be? #define CCSPEED 3 -#define CCDELAY(x) delay(x) +//#define CCDELAY(x) delay(x) +#define CCDELAY(x) #define SETMOSI P5OUT|=MOSI #define CLRMOSI P5OUT&=~MOSI @@ -53,24 +54,39 @@ void ccsetup(){ P5OUT|=MOSI+SCK+RST; P5DIR|=MOSI+SCK+RST; //P5DIR&=~MISO; //MOSI is MISO + + //P5REN=0xFF; + } //! Initialize the debugger void ccdebuginit(){ + delay(30); //So the beginning is ready for glitching. + //Two positive debug clock pulses while !RST is low. //Take RST low, pulse twice, then high. P5OUT&=~SCK; P5OUT&=~RST; - //pulse twice + /* + //pulse twice, old code. CCDELAY(CCSPEED); P5OUT|=SCK; //up CCDELAY(CCSPEED); P5OUT&=~SCK; //down CCDELAY(CCSPEED); + P5OUT|=SCK; //up CCDELAY(CCSPEED); P5OUT&=~SCK; //down + CCDELAY(CCSPEED); + */ + + P5OUT^=SCK; + P5OUT^=SCK; + P5OUT^=SCK; + P5OUT^=SCK; //Unnecessary. + //Raise !RST. P5OUT|=RST; @@ -126,20 +142,33 @@ void cchandle(unsigned char app, unsigned char verb, unsigned long len){ //Always init. Might help with buggy lines. - ccdebuginit(); + //Might hurt too. + //ccdebuginit(); + long i; switch(verb){ //CC_PEEK and CC_POKE will come later. + case PEEK: + cmddata[0]=cc_peekirambyte(cmddata[0]); + txdata(app,verb,1); + break; + case POKE: + cmddata[0]=cc_pokeirambyte(cmddata[0],cmddata[1]); + txdata(app,verb,0); + break; case READ: //Write a command and return 1-byte reply. cccmd(len); - ccread(1); + if(cmddata[0]&0x4) + ccread(1); txdata(app,verb,1); + break; case WRITE: //Write a command with no reply. cccmd(len); txdata(app,verb,0); break; case START://enter debugger + ccsetup(); ccdebuginit(); txdata(app,verb,0); break; @@ -172,6 +201,9 @@ void cchandle(unsigned char app, cc_get_pc(); txdata(app,verb,2); break; + case CC_LOCKCHIP: + cc_lockchip(); + //no break, return status case CC_READ_STATUS: cc_read_status(); txdata(app,verb,1); @@ -200,7 +232,7 @@ void cchandle(unsigned char app, txdata(app,NOK,0);//TODO add me break; case CC_GET_CHIP_ID: - cc_get_chip_id(); + cmddataword[0]=cc_get_chip_id(); txdata(app,verb,2); break; @@ -226,6 +258,11 @@ void cchandle(unsigned char app, cc_write_flash_page(cmddatalong[0]); txdata(app,verb,0); break; + case CC_WIPEFLASHBUFFER: + for(i=0xf000;i<0xf800;i++) + cc_pokedatabyte(i,0xFF); + txdata(app,verb,0); + break; case CC_MASS_ERASE_FLASH: case CC_CLOCK_INIT: case CC_PROGRAM_FLASH: @@ -237,9 +274,10 @@ void cchandle(unsigned char app, //! Set the Chipcon's Program Counter void cc_set_pc(u32 adr){ - cmddata[0]=0x02; //GetPC - cmddata[1]=(adr>>8)&0xff; //HIBYTE - cmddata[2]=adr&0xff; //LOBYTE + cmddata[0]=0x02; //SetPC + cmddata[1]=((adr>>8)&0xff); //HIBYTE + cmddata[2]=adr&0xff; //LOBYTE + cc_debug_instr(3); return; } @@ -256,6 +294,28 @@ void cc_wr_config(unsigned char config){ cccmd(2); ccread(1); } + +//! Locks the chip. +void cc_lockchip(){ + register int i; + + //debugstr("Locking chip."); + cc_wr_config(1);//Select Info Flash + if(!(cc_rd_config()&1)) + debugstr("Config forgotten!"); + + //Clear config page. + for(i=0;i<2048;i++) + cc_pokedatabyte(0xf000+i,0); + cc_write_flash_page(0); + if(cc_peekcodebyte(0)) + debugstr("Failed to clear info flash byte."); + + cc_wr_config(0); + if(cc_rd_config()&1) + debugstr("Stuck in info flash mode!"); +} + //! Read the configuration byte. unsigned char cc_rd_config(){ cmddata[0]=CCCMD_RD_CONFIG; //0x24 @@ -275,15 +335,30 @@ unsigned char cc_read_status(){ //! Read the CHIP ID bytes. unsigned short cc_get_chip_id(){ - unsigned short toret; cmddata[0]=CCCMD_GET_CHIP_ID; //0x68 cccmd(1); ccread(2); + + + //Find the flash word size. + switch(cmddata[0]){ + case 0x01://CC1110 + case 0x81://CC2510 + case 0x91://CC2511 + flash_word_size=0x02; + //debugstr("2 bytes/flash word"); + break; + default: + debugstr("Warning: Guessing flash word size."); + case 0x85://CC2430 + case 0x89://CC2431 + //debugstr("4 bytes/flash word"); + flash_word_size=0x04; + break; + } //Return the word. - toret=cmddata[1]; - toret=(toret<<8)+cmddata[1]; - return toret; + return cmddataword[0]; } //! Populates flash buffer in xdata. @@ -301,25 +376,51 @@ void cc_write_xdata(u16 adr, u8 *data, u16 len){ //32-bit words, 2KB pages +//0x20 0x00 for CC2430, CC1110 #define HIBYTE_WORDS_PER_FLASH_PAGE 0x02 #define LOBYTE_WORDS_PER_FLASH_PAGE 0x00 -#define FLASHPAGE_SIZE 0x800 -//2 bytes/word -#define FLASH_WORD_SIZE 0x4 +/** Ugh, this varies by chip. + 0x800 for CC2430 + 0x400 for CC1110 +*/ +//#define FLASHPAGE_SIZE 0x400 +#define MAXFLASHPAGE_SIZE 0x800 +#define MINFLASHPAGE_SIZE 0x400 + + +//32 bit words on CC2430 +//16 bit words on CC1110 +//#define FLASH_WORD_SIZE 0x2 +u8 flash_word_size = 0; //0x02; + + +/* Flash Write Timing + MHZ | FWT (0xAB) + 12 | 0x10 + 13 | 0x11 + 16 | 0x15 + 24 | 0x20 + 26 | 0x23 (IM ME) + 32 | 0x2A (Modula.si) +*/ +//#define FWT 0x23 const u8 flash_routine[] = { + //0: //MOV FADDRH, #imm; 0x75, 0xAD, 0x00,//#imm=((address >> 8) / FLASH_WORD_SIZE) & 0x7E, + //0x75, 0xAB, 0x23, //Set FWT per clock 0x75, 0xAC, 0x00, // MOV FADDRL, #00; - /* Erase page. * + /* Erase page. */ 0x75, 0xAE, 0x01, // MOV FLC, #01H; // ERASE // ; Wait for flash erase to complete 0xE5, 0xAE, // eraseWaitLoop: MOV A, FLC; 0x20, 0xE7, 0xFB, // JB ACC_BUSY, eraseWaitLoop; - */ + + /* End erase page. */ // ; Initialize the data pointer 0x90, 0xF0, 0x00, // MOV DPTR, #0F000H; // ; Outer loops @@ -327,7 +428,8 @@ const u8 flash_routine[] = { 0x7E, LOBYTE_WORDS_PER_FLASH_PAGE, // MOV R6, #imm; 0x75, 0xAE, 0x02, // MOV FLC, #02H; // WRITE // ; Inner loops - 0x7D, FLASH_WORD_SIZE, // writeLoop: MOV R5, #imm; + //24: + 0x7D, 0xde /*FLASH_WORD_SIZE*/, // writeLoop: MOV R5, #imm; 0xE0, // writeWordLoop: MOVX A, @DPTR; 0xA3, // INC DPTR; 0xF5, 0xAF, // MOV FWDATA, A; @@ -339,28 +441,61 @@ const u8 flash_routine[] = { 0xDF, 0xEF, // DJNZ R7, writeLoop; // ; Done, fake a breakpoint 0xA5 // DB 0xA5; -}; +}; + //! Copies flash buffer to flash. void cc_write_flash_page(u32 adr){ //Assumes that page has already been written to XDATA 0xF000 + //debugstr("Flashing 2kb at 0xF000 to given adr."); + + if(adr&(MINFLASHPAGE_SIZE-1)){ + debugstr("Flash page address is not on a page boundary. Aborting."); + return; + } + + if(flash_word_size==0){ + debugstr("Flash word size is wrong."); + while(1); + } //Routine comes next //WRITE_XDATA_MEMORY(IN: 0xF000 + FLASH_PAGE_SIZE, sizeof(routine), routine); - cc_write_xdata(0xF000+FLASHPAGE_SIZE, + cc_write_xdata(0xF000+MAXFLASHPAGE_SIZE, (u8*) flash_routine, sizeof(flash_routine)); //Patch routine's third byte with //((address >> 8) / FLASH_WORD_SIZE) & 0x7E - cc_pokedatabyte(0xF000+FLASHPAGE_SIZE+2, - ((adr>>8)/FLASH_WORD_SIZE)&0x7E); - cc_debug(3, //MOV MEMCTR, (bank * 16) + 1; - 0x75, 0xc7, 0x51); - cc_set_pc(0xf000+FLASHPAGE_SIZE);//execute code fragment + cc_pokedatabyte(0xF000+MAXFLASHPAGE_SIZE+2, + ((adr>>8)/flash_word_size)&0x7E); + //Patch routine to define FLASH_WORD_SIZE + if(flash_routine[25]!=0xde) + debugstr("Ugly patching code failing in chipcon.c"); + cc_pokedatabyte(0xF000+MAXFLASHPAGE_SIZE+25, + flash_word_size); + + //debugstr("Wrote flash routine."); + + + //MOV MEMCTR, (bank * 16) + 1; + cmddata[0]=0x75; + cmddata[1]=0xc7; + cmddata[2]=0x51; + cc_debug_instr(3); + //debugstr("Loaded bank info."); + + cc_set_pc(0xf000+MAXFLASHPAGE_SIZE);//execute code fragment cc_resume(); + + //debugstr("Executing."); + + while(!(cc_read_status()&CC_STATUS_CPUHALTED)){ - P1OUT^=1;//blink LED + P1OUT^=1;//blink LED while flashing } + + //debugstr("Done flashing."); + P1OUT&=~1;//clear LED } @@ -427,11 +562,11 @@ unsigned char cc_debug(unsigned char len, unsigned char cmd=CCCMD_DEBUG_INSTR+(len&0x3);//0x54+len CCWRITE; cctrans8(cmd); - if(len--) + if(len>0) cctrans8(a); - if(len--) + if(len>1) cctrans8(b); - if(len--) + if(len>2) cctrans8(c); CCREAD; return cctrans8(0x00); @@ -492,21 +627,31 @@ for (n = 0; n < count; n++) { unsigned char cc_peekdatabyte(unsigned int adr){ unsigned char hb=(adr&0xFF00)>>8, - lb=adr&0xFF, - toret; - + lb=adr&0xFF; + //MOV DPTR, adr cc_debug(3, 0x90, hb, lb); //MOVX A, @DPTR //Must be 2, perhaps for clocking? - toret=cc_debug(3, 0xE0, 0, 0); - return toret; - - /* -DEBUG_INSTR(IN: 0x90, HIBYTE(address), LOBYTE(address), OUT: Discard); -for (n = 0; n < count; n++) { - DEBUG_INSTR(IN: 0xE0, OUT: outputArray[n]); - DEBUG_INSTR(IN: 0xA3, OUT: Discard); + return cc_debug(3, 0xE0, 0, 0); } - */ + + +//! Fetch a byte of IRAM. +u8 cc_peekirambyte(u8 adr){ + //CLR A + cc_debug(2, 0xE4, 0, 0); + //MOV A, #iram + return cc_debug(3, 0xE5, adr, 0); } + +//! Write a byte of IRAM. +u8 cc_pokeirambyte(u8 adr, u8 val){ + //CLR A + cc_debug(2, 0xE4, 0, 0); + //MOV #iram, #val + return cc_debug(3, 0x75, adr, val); + //return cc_debug(3, 0x75, val, adr); +} + +