mainmenu_option next_comment comment 'Block device drivers' tristate 'Loopback device support' CONFIG_BLK_DEV_LOOP dep_tristate 'Network block device support' CONFIG_BLK_DEV_NBD $CONFIG_NET tristate 'RAM disk support' CONFIG_BLK_DEV_RAM if [ "$CONFIG_BLK_DEV_RAM" = "y" -o "$CONFIG_BLK_DEV_RAM" = "m" ]; then int ' Default RAM disk size' CONFIG_BLK_DEV_RAM_SIZE 24576 fi dep_bool ' Initial RAM disk (initrd) support' CONFIG_BLK_DEV_INITRD $CONFIG_BLK_DEV_RAM tristate 'XPRAM disk support' CONFIG_BLK_DEV_XPRAM comment 'S/390 block device drivers' tristate 'Support for DASD devices' CONFIG_DASD if [ "$CONFIG_DASD" != "n" ]; then dep_tristate ' Support for ECKD Disks' CONFIG_DASD_ECKD $CONFIG_DASD if [ "$CONFIG_DASD_ECKD" = "m" ]; then bool ' Automatic activation of ECKD module' CONFIG_DASD_AUTO_ECKD fi dep_tristate ' Support for FBA Disks' CONFIG_DASD_FBA $CONFIG_DASD if [ "$CONFIG_DASD_FBA" = "m" ]; then bool ' Automatic activation of FBA module' CONFIG_DASD_AUTO_FBA fi # dep_tristate ' Support for CKD Disks' CONFIG_DASD_CKD $CONFIG_DASD if [ "$CONFIG_ARCH_S390X" != "y" ]; then dep_tristate ' Support for DIAG access to CMS reserved Disks' CONFIG_DASD_DIAG $CONFIG_DASD if [ "$CONFIG_DASD_DIAG" = "m" ]; then bool ' Automatic activation of DIAG module' CONFIG_DASD_AUTO_DIAG fi fi fi endmenu source drivers/md/Config.in mainmenu_option next_comment comment 'Character device drivers' bool 'Unix98 PTY support' CONFIG_UNIX98_PTYS if [ "$CONFIG_UNIX98_PTYS" = "y" ]; then int 'Maximum number of Unix98 PTYs in use (0-2048)' CONFIG_UNIX98_PTY_COUNT 256 fi comment 'S/390 character device drivers' tristate 'Support for locally attached 3270 tubes' CONFIG_TN3270 if [ "$CONFIG_TN3270" = "y" ]; then bool 'Support for console on 3270 line mode terminal' CONFIG_TN3270_CONSOLE fi bool 'Support for 3215 line mode terminal' CONFIG_TN3215 if [ "$CONFIG_TN3215" = "y" ]; then bool 'Support for console on 3215 line mode terminal' CONFIG_TN3215_CONSOLE fi bool 'Support for HWC line mode terminal' CONFIG_HWC if [ "$CONFIG_HWC" = "y" ]; then bool ' console on HWC line mode terminal' CONFIG_HWC_CONSOLE tristate ' Control-Program Identification' CONFIG_HWC_CPI fi tristate 'S/390 tape device support' CONFIG_S390_TAPE if [ "$CONFIG_S390_TAPE" != "n" ]; then comment 'S/390 tape interface support' bool ' Support for tape character devices' CONFIG_S390_TAPE_CHAR bool ' Support for tape block devices' CONFIG_S390_TAPE_BLOCK comment 'S/390 tape hardware support' bool ' Support for 3490 tape hardware' CONFIG_S390_TAPE_3490 bool ' Support for 3480 tape hardware' CONFIG_S390_TAPE_3480 fi endmenu if [ "$CONFIG_NET" = "y" ]; then mainmenu_option next_comment comment 'Network device drivers' bool 'Network device support' CONFIG_NETDEVICES if [ "$CONFIG_NETDEVICES" = "y" ]; then tristate 'Dummy net driver support' CONFIG_DUMMY tristate 'Bonding driver support' CONFIG_BONDING tristate 'EQL (serial line load balancing) support' CONFIG_EQUALIZER tristate 'Universal TUN/TAP device driver support' CONFIG_TUN bool 'Ethernet (10 or 100Mbit)' CONFIG_NET_ETHERNET bool 'Token Ring driver support' CONFIG_TR dep_tristate 'Cisco 7000 support' CONFIG_C7000 m bool 'FDDI driver support' CONFIG_FDDI comment 'S/390 network device drivers' bool 'Channel Device Configuration' CONFIG_CHANDEV if [ "$CONFIG_CHANDEV" = "y" ]; then define_bool CONFIG_HOTPLUG y fi if [ "$CONFIG_QDIO" != "n" -a "$CONFIG_CHANDEV" = "y" -a "$CONFIG_IP_MULTICAST" = "y" ]; then dep_tristate 'Support for Gigabit Ethernet' CONFIG_QETH $CONFIG_QDIO if [ "$CONFIG_QETH" != "n" ]; then comment 'Gigabit Ethernet default settings' if [ "$CONFIG_IPV6" = "y" -o "$CONFIG_IPV6" = "$CONFIG_QETH" ]; then bool ' IPv6 support for qeth' CONFIG_QETH_IPV6 else define_bool CONFIG_QETH_IPV6 n fi if [ "$CONFIG_VLAN_8021Q" = "y" -o "$CONFIG_VLAN_8021Q" = "$CONFIG_QETH" ]; then bool ' VLAN support for qeth' CONFIG_QETH_VLAN else define_bool CONFIG_QETH_VLAN n fi bool ' Performance statistics in /proc' CONFIG_QETH_PERF_STATS fi fi tristate 'CTC device support' CONFIG_CTC tristate 'IUCV device support (VM only)' CONFIG_IUCV fi endmenu fi