#include "command.h"
#include "glitch.h"
-//! Disable glitch state at init.
+
+//! Call this before the function to be glitched.
+void glitchprime(){
+#ifdef DAC12IR
+ WDTCTL = WDTPW + WDTHOLD; // Stop WDT
+
+ glitchsetup();
+ _EINT();
+ return;
+#endif
+}
+
+//! Setup glitching.
void glitchsetup(){
#ifdef DAC12IR
//Set GSEL high to disable glitching.
-
- P5DIR|=0x80;
- P6DIR|=0x40;
- P5OUT|=0x80;
- P6OUT|=0x40;
+ //Normal voltage, use resistors instead of output.
+ //P5DIR=0x80; //ONLY glitch pin is output.
+ P5OUT|=0x80; //It MUST begin high.
+ //P5REN|=0x7F; //Resistors pull high and low weakly.
+
+ P6DIR|=BIT6+BIT5;
+ P6OUT|=BIT6+BIT5;
- glitchsetupdac();
+ WDTCTL = WDTPW + WDTHOLD; // Stop WDT
+ TACTL = TASSEL1 + TACLR; // SMCLK, clear TAR
+ CCTL0 = CCIE; // CCR0 interrupt enabled
+ CCR0 = glitchcount+0x10; // Compare Value
+ TACTL |= MC_2; // continuous mode.
#endif
}
-//! Setup analog chain for glitching.
-void glitchsetupdac(){
-#ifdef DAC12IR
+// Timer A0 interrupt service routine
+interrupt(TIMERA0_VECTOR) Timer_A (void){
+ P5OUT&=~BIT7;//Glitch
+ //P5DIR=BIT7; //All else high impedance.
+ P5OUT|=BIT7;//Normal
+ TACTL |= MC0;// Stop Timer_A;
+ return;
+}
+
+
+u16 glitchcount=0;
+
+//! Glitch an application.
+void glitchapp(u8 app){
+ debugstr("That app is not yet supported.");
+}
+
+
+//! Set glitching voltages.
+void glitchvoltages(u16 gnd, u16 vcc){
int i;
+ //debugstr("Set glitching voltages: GND and VCC");
+ //debughex(gnd);
+ //debughex(vcc);
+
+ /** N.B., because this is confusing as hell. As per Page 86 of
+ SLAS541F, P6SEL is not what controls the use of the DAC0/DAC1
+ functions on P6.6 and P6.5. Instead, CAPD or DAC12AMP>0 sets
+ the state.
+ */
+
+ #ifdef DAC12IR
ADC12CTL0 = REF2_5V + REFON; // Internal 2.5V ref on
// Delay here for reference to settle.
for(i=0;i!=0xFFFF;i++) asm("nop");
DAC12_0CTL = DAC12IR + DAC12AMP_5 + DAC12ENC; // Int ref gain 1
+ DAC12_1CTL = DAC12IR + DAC12AMP_5 + DAC12ENC; // Int ref gain 1
// 1.0V 0x0666, 2.5V 0x0FFF
- DAC12_0DAT = 0x0FFF;
- //DAC12_0DAT = 0x0880;
- //__bis_SR_register(LPM0_bits + GIE); // Enter LPM0
-#endif
+ DAC12_0DAT = vcc; //high;
+ DAC12_1DAT = gnd; //low;
+ #endif
+}
+//! Set glitching rate.
+void glitchrate(u16 rate){
+ glitchcount=rate;
+}
+
+//! Handles a monitor command.
+void glitchhandle(unsigned char app,
+ unsigned char verb,
+ unsigned long len){
+ switch(verb){
+ case GLITCHVOLTAGES:
+ glitchvoltages(cmddataword[0],
+ cmddataword[1]);
+ txdata(app,verb,0);
+ break;
+ case GLITCHRATE:
+ glitchrate(cmddataword[0]);
+ txdata(app,verb,0);
+ break;
+ case GLITCHVERB:
+ //FIXME parameters don't work yet.
+ glitchprime();
+ handle(cmddata[0],cmddata[1],0);
+ break;
+ case GLITCHTIME:
+ _DINT();//disable interrupts
+ TACTL=0; //clear dividers
+ TACTL|=TACLR; //clear config
+ TACTL|=TASSEL_SMCLK| //smclk source
+ MC_2; //continuous mode.
+
+ //perform the function
+ silent++;//Don't want the function to return anything.
+ handle(cmddata[0],cmddata[1],0);
+ silent--;
+ cmddataword[0]=TAR; //Return counter.
+ txdata(app,verb,2);
+ break;
+ case START:
+ //Testing mode, for looking at the glitch waveform.
+ glitchvoltages(0xFFF,0);//Inverted VCC and GND.
+ P5OUT|=BIT7;//Normal
+ P5DIR|=BIT7;
+ while(1){
+ P5OUT&=~BIT7;//Glitch
+ //asm("nop");//asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");
+ asm("nop"); //Not necessary.
+ P5OUT|=BIT7;//Normal
+ asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");
+ asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");asm("nop");
+ }
+ txdata(app,verb,0);
+ break;
+ case STOP:
+ case GLITCHAPP:
+ default:
+ debugstr("Unknown glitching verb.");
+ txdata(app,NOK,0);
+ }
}