+5V RAW
2 433Mhz receive
+ 3 433Mhz outdoor temperature sensor receiver
10 433Mhz send
11 DS18B20
+ 13 513Mhz send
*/
OneWire oneWire(11);
DallasTemperature sensors(&oneWire);
+
+// 513Mhz light sockets
+#define TX_PIN 12
+#define LED_PIN 13
+
+int int_0 = 300; // ms
+int int_1 = 900; // ms
+int wait = 2000; // ms
+int repeat = 5; // times
+
+void send_513(char *code) {
+ Serial.print("send 513Mhz ");
+ Serial.println(code);
+
+ // we have to send same signal at least two times
+ for(int r = 0; r < repeat; r++ ) {
+
+ digitalWrite(LED_PIN, HIGH);
+
+ for(int i = 0; i < strlen(code); i++) {
+ int i1 = int_0;
+ int i2 = int_1;
+ if (code[i] == '1' ) {
+ i1 = int_1;
+ i2 = int_0;
+ }
+ digitalWrite(TX_PIN, HIGH);
+ delayMicroseconds(i1);
+ digitalWrite(TX_PIN, LOW);
+ delayMicroseconds(i2);
+ }
+
+ delayMicroseconds(wait); // guess
+ }
+
+ digitalWrite(LED_PIN, LOW);
+}
+
+
+// outdoor 433 MHz temperature sensor
+
+// Unknown 433Mhz weather sensor decoder. Untested in the real world.
+// http://arduino.cc/forum/index.php/topic,142871.msg1106336.html#msg1106336
+
+// __ ___ ___ ___
+// | | | | | | |
+// |_________| |______| |___| |
+//
+// | Sync | 1 | 0 |
+// | 9780us | 4420us | 2410us
+// 9810 4410 2490
+
+// Defines
+#define DataBits0 4 // Number of data0 bits to expect
+#define DataBits1 32 // Number of data1 bits to expect
+#define allDataBits 36 // Number of data sum 0+1 bits to expect
+// isrFlags bit numbers
+#define F_HAVE_DATA 1 // 0=Nothing in read buffer, 1=Data in read buffer
+#define F_GOOD_DATA 2 // 0=Unverified data, 1=Verified (2 consecutive matching reads)
+#define F_CARRY_BIT 3 // Bit used to carry over bit shift from one long to the other
+#define F_STATE 7 // 0=Sync mode, 1=Data mode
+
+// uno: pin 2 = int.0 or pin 3 = int.1 see
+// http://arduino.cc/en/Reference/attachInterrupt
+#define ISR_PIN 3
+#define ISR_INT 1
+
+// Constants
+const unsigned long sync_MIN = 9000; // Minimum Sync time in micro seconds
+const unsigned long sync_MAX = 10000;
+
+const unsigned long bit1_MIN = 4000;
+const unsigned long bit1_MAX = 5000;
+
+const unsigned long bit0_MIN = 2000;
+const unsigned long bit0_MAX = 3000;
+
+const unsigned long glitch_Length = 300; // Anything below this value is a glitch and will be ignored.
+
+// Interrupt variables
+unsigned long fall_Time = 0; // Placeholder for microsecond time when last falling edge occured.
+unsigned long rise_Time = 0; // Placeholder for microsecond time when last rising edge occured.
+byte bit_Count = 0; // Bit counter for received bits.
+unsigned long build_Buffer[] = {0,0}; // Placeholder last data packet being received.
+volatile unsigned long read_Buffer[] = {0,0}; // Placeholder last full data packet read.
+volatile byte isrFlags = 0; // Various flag bits
+volatile unsigned long last_Buffer[] = {0,0};
+unsigned long last_Time = 0;
+
+void PinChangeISR(){ // Pin 2 (Interrupt 0) service routine
+ unsigned long Time = micros(); // Get current time
+ if (digitalRead(ISR_PIN) == LOW) {
+// Falling edge
+ if (Time > (rise_Time + glitch_Length)) {
+// Not a glitch
+ Time = micros() - fall_Time; // Subtract last falling edge to get pulse time.
+ if (bitRead(build_Buffer[1],31) == 1)
+ bitSet(isrFlags, F_CARRY_BIT);
+ else
+ bitClear(isrFlags, F_CARRY_BIT);
+
+ if (bitRead(isrFlags, F_STATE) == 1) {
+// Looking for Data
+ if ((Time > bit0_MIN) && (Time < bit0_MAX)) {
+// 0 bit
+ build_Buffer[1] = build_Buffer[1] << 1;
+ build_Buffer[0] = build_Buffer[0] << 1;
+ if (bitRead(isrFlags,F_CARRY_BIT) == 1)
+ bitSet(build_Buffer[0],0);
+ bit_Count++;
+ }
+ else if ((Time > bit1_MIN) && (Time < bit1_MAX)) {
+// 1 bit
+ build_Buffer[1] = build_Buffer[1] << 1;
+ bitSet(build_Buffer[1],0);
+ build_Buffer[0] = build_Buffer[0] << 1;
+ if (bitRead(isrFlags,F_CARRY_BIT) == 1)
+ bitSet(build_Buffer[0],0);
+ bit_Count++;
+ }
+ else {
+// Not a 0 or 1 bit so restart data build and check if it's a sync?
+ bit_Count = 0;
+ build_Buffer[0] = 0;
+ build_Buffer[1] = 0;
+ bitClear(isrFlags, F_GOOD_DATA); // Signal data reads dont' match
+ bitClear(isrFlags, F_STATE); // Set looking for Sync mode
+ if ((Time > sync_MIN) && (Time < sync_MAX)) {
+ // Sync length okay
+ bitSet(isrFlags, F_STATE); // Set data mode
+ }
+ }
+ if (bit_Count >= allDataBits) {
+// All bits arrived
+ bitClear(isrFlags, F_GOOD_DATA); // Assume data reads don't match
+ if (build_Buffer[0] == read_Buffer[0]) {
+ if (build_Buffer[1] == read_Buffer[1])
+ bitSet(isrFlags, F_GOOD_DATA); // Set data reads match
+ }
+ read_Buffer[0] = build_Buffer[0];
+ read_Buffer[1] = build_Buffer[1];
+ last_Buffer[0] = build_Buffer[0];
+ last_Buffer[1] = build_Buffer[1];
+ last_Time = micros();
+ bitSet(isrFlags, F_HAVE_DATA); // Set data available
+ bitClear(isrFlags, F_STATE); // Set looking for Sync mode
+digitalWrite(13,HIGH); // Used for debugging
+ build_Buffer[0] = 0;
+ build_Buffer[1] = 0;
+ bit_Count = 0;
+ }
+ }
+ else {
+// Looking for sync
+ if ((Time > sync_MIN) && (Time < sync_MAX)) {
+// Sync length okay
+ build_Buffer[0] = 0;
+ build_Buffer[1] = 0;
+ bit_Count = 0;
+ bitSet(isrFlags, F_STATE); // Set data mode
+digitalWrite(13,LOW); // Used for debugging
+ }
+ }
+ fall_Time = micros(); // Store fall time
+ }
+ }
+ else {
+// Rising edge
+ if (Time > (fall_Time + glitch_Length)) {
+ // Not a glitch
+ rise_Time = Time; // Store rise time
+ }
+ }
+}
+
+
+
+void serial_outdoor_dump(void) {
+
+
+ unsigned long t = micros() - last_Time;
+ if ( t > 60 * 1000 * 1000 ) { // 60 s timeout
+ Serial.print("# data too old ");
+ Serial.println(t);
+ return;
+ }
+
+
+ unsigned long myData0 = 0;
+ unsigned long myData1 = 0;
+
+ // We have at least 2 consecutive matching reads
+ myData0 = last_Buffer[0]; // first 4 bits
+ myData1 = last_Buffer[1]; // rest of 32 bits
+ bitClear(isrFlags,F_HAVE_DATA); // Flag we have read the data
+
+ Serial.print("temp=");
+ int temp = ( myData1 >> 8 ) & 0xFFF;
+ if ( temp & 0x800 ) temp = temp | 0xF000;
+ Serial.print(temp / 10.0, 1);
+
+ Serial.print(" humidity=");
+ Serial.print( myData1 & 0xFF );
+
+ byte b1 = ( myData1 >> 20 ); // second byte from received packet
+
+ Serial.print(" button=");
+ Serial.print( b1 & 0x04);
+
+ Serial.print(" battery=");
+ Serial.print( b1 & 0x08);
+
+ Serial.print(" channel=");
+ Serial.print( ( b1 & 0x03 ) + 1 );
+
+ Serial.print(" rid=");
+ Serial.println( myData1 >> 24 );
+
+}
+
+
+
+// setup
+
void setup() {
Serial.begin(9600);
mySwitch.enableReceive(0); // Receiver on inerrupt 0 => that is pin #2
// DS18B20
sensors.begin();
+ // outdoor temperature sensor
+ pinMode(13,OUTPUT); // Used for debugging
+ pinMode(ISR_PIN,INPUT);
+ attachInterrupt(ISR_INT,PinChangeISR,CHANGE);
+
+
Serial.print("press buttons on remote or send AB where A = socket (0..9), B = state (0 = off, 1 = on)\nB00...00 (24 digits) to send binary\n");
}
sensors.requestTemperatures();
Serial.println( sensors.getTempCByIndex(0) );
} else
+
if ( input == 'B' ) {
Serial.readBytesUntil('\n', binary_data, sizeof(binary_data));
Serial.print("send B");
Serial.println( binary_data );
mySwitch.send( binary_data );
} else
+
+ // light sockets at 513 Mhz
+ if (input == 'a') {
+ send_513("1000100110110000000000010");
+ } else
+ if (input == 'b') {
+ send_513("1011001001011111000000010");
+ } else
+
+ if (input == 'o') {
+ serial_outdoor_dump();
+ }
+
if ( input >= 0x30 && input <= 0x39 ) {
input = input - 0x30; // ASCII to number
serial_data[serial_pos++] = input;