execute all tests just once

[Arduino] / c2_ulx3s_test / c2_ulx3s_test.ino

diff --git a/c2_ulx3s_test/c2_ulx3s_test.ino b/c2_ulx3s_test/c2_ulx3s_test.ino
index ff0493c..475319c 100644 (file)
--- a/c2_ulx3s_test/c2_ulx3s_test.ino
+++ b/c2_ulx3s_test/c2_ulx3s_test.ino
@@ -96,6 +96,7 @@ void video_init()
 
 void setup()
 {
+  Serial.println("setup start");
   video_init();
   rtc_init();
   adc_init();
@@ -104,22 +105,74 @@ void setup()
   oled_init();
   rds_init();
   pcm_init();
+  rtc_set_clock();
+  rtc_set_alarm();
+  Serial.println("setup end");
 }
 
+int rtc_ok = 0;
+int edid_ok = 0;
+int adc_ok = 0;
+int dac_ok = 0;
+int btn_ok = 0;
+int flash_ok = 0;
+int sd_ok = 0;
+
+int all_ok = 0;
+int last_all_ok = -1;
+
+int led_beat = 0;
+
+
 void loop()
 {
   static uint8_t counter = 0;
   const int nlines = 6;
   char line[nlines][256];
+
+  digitalWrite(8+7, led_beat);
+  led_beat = !led_beat;
+
+#if 0
   if(1 & ++counter)
     pcm_tone();
   else
     pcm_mute();
-  rtc_read(line[0]);
-  edid_read(line[1]);
-  adc_read(line[2]);
-  dac_read(line[3]);
-  btn_read(line[4]); // buttons. DIP switches and blink LEDs
+#endif
+
+  if ( rtc_ok == 0 ) rtc_ok = rtc_read(line[0]);
+  if ( rtc_ok == 1 ) {
+    Serial.println("RTC OK");
+    rtc_ok++;
+    all_ok++;
+  }
+  if ( edid_ok == 0 ) edid_ok = edid_read(line[1]);
+  if ( edid_ok == 1 ) {
+    Serial.println("EDID OK");
+    edid_ok++;
+    all_ok++;
+  }
+  if ( adc_ok < 8 ) adc_ok = adc_read(line[2]);
+  if ( adc_ok == 8 ) {
+    Serial.println("ADC OK");
+    adc_ok++;
+    all_ok++;
+  }
+  if ( dac_ok == 0 ) dac_ok = dac_read(line[3]);
+  if ( dac_ok == 1 ) {
+    Serial.println("DAC OK");
+    dac_ok++;
+    all_ok++;
+  }
+  
+  int btn = btn_read(line[4]); // buttons. DIP switches and blink LEDs
+  if ( btn_ok == 0 && btn == 7 ) {
+    Serial.println("BTN OK");
+    btn_ok++;
+    all_ok++;
+  }
+
+#if 0
   if(line[4][5] == '1') // BTN1 pressed
   {
     rtc_set_clock();
@@ -131,19 +184,40 @@ void loop()
     volatile uint32_t *simple_out = (uint32_t *)0xFFFFFF10;
     simple_out[0] |= (1<<13); // bit 13 of simple_out is shutdown
   }
+#endif
   char flash_str[64], sd_str[64], oled_str[64];
-  flash_read(flash_str);
-  sd_read(sd_str); // esp32 must be flashed not to access SD card
+  if ( flash_ok == 0 ) flash_ok = flash_read(flash_str);
+  if ( flash_ok == 1 ) {
+    Serial.println("FLASH OK");
+    flash_ok++;
+    all_ok++;
+  }
+  
+  if ( sd_ok == 0 ) sd_ok = sd_read(sd_str); // esp32 must be flashed not to access SD card
+  if ( sd_ok == 1 ) {
+    Serial.println("SD OK");
+    sd_ok++;
+    all_ok++;
+  }
+
+#if 0
   oled_read(oled_str);
+#endif
+
+  Serial.print("all_ok=");
+  Serial.println(all_ok);
+
   sprintf(line[5], "%s %s   %s\n", flash_str, oled_str, sd_str);
   line[6][0]='\0';
   //ram_test(line[5]); // works but too slow, need speedup
   Serial.println("");
   for(int i = 0; i < nlines; i++)
     Serial.print(line[i]);
+
   cls();
   for(int i = 0; i < nlines; i++)
     prints(line[i]);
+  
   while((*c2.vblank_reg & 0x80) == 0);
   c2.sprite_refresh();
   // delay(1000);