+++ /dev/null
-###############################################################################
-#
-# EXAMPLE.conf:
-# An example configuration file for configuring the ucd-snmp snmpd agent.
-#
-###############################################################################
-#
-# This file is intended to only be an example. If, however, you want
-# to use it, it should be placed in SYSCONFDIR/share/snmp/snmpd.conf.
-# When the snmpd agent starts up, this is where it will look for it.
-#
-# You might be interested in generating your own snmpd.conf file using
-# the "snmpconf" program (perl script) instead. It's a nice menu
-# based interface to writing well commented configuration files. Try it!
-#
-# Note: This file is automatically generated from EXAMPLE.conf.def.
-# Do NOT read the EXAMPLE.conf.def file! Instead, after you have run
-# configure & make, and then make sure you read the EXAMPLE.conf file
-# instead, as it will tailor itself to your configuration.
-
-# All lines beginning with a '#' are comments and are intended for you
-# to read. All other lines are configuration commands for the agent.
-
-#
-# PLEASE: read the snmpd.conf(5) manual page as well!
-#
-
-
-###############################################################################
-# Access Control
-###############################################################################
-
-# YOU SHOULD CHANGE THE "COMMUNITY" TOKEN BELOW TO A NEW KEYWORD ONLY
-# KNOWN AT YOUR SITE. YOU *MUST* CHANGE THE NETWORK TOKEN BELOW TO
-# SOMETHING REFLECTING YOUR LOCAL NETWORK ADDRESS SPACE.
-
-# By far, the most common question I get about the agent is "why won't
-# it work?", when really it should be "how do I configure the agent to
-# allow me to access it?"
-#
-# By default, the agent responds to the "public" community for read
-# only access, if run out of the box without any configuration file in
-# place. The following examples show you other ways of configuring
-# the agent so that you can change the community names, and give
-# yourself write access as well.
-#
-# The following lines change the access permissions of the agent so
-# that the COMMUNITY string provides read-only access to your entire
-# NETWORK (EG: 10.10.10.0/24), and read/write access to only the
-# localhost (127.0.0.1, not its real ipaddress).
-#
-# For more information, read the FAQ as well as the snmpd.conf(5)
-# manual page.
-
-####
-# First, map the community name (COMMUNITY) into a security name
-# (local and mynetwork, depending on where the request is coming
-# from):
-
-# sec.name source community
-com2sec local localhost COMMUNITY
-com2sec mynetwork NETWORK/24 COMMUNITY
-
-####
-# Second, map the security names into group names:
-
-# sec.model sec.name
-group MyRWGroup v1 local
-group MyRWGroup v2c local
-group MyRWGroup usm local
-group MyROGroup v1 mynetwork
-group MyROGroup v2c mynetwork
-group MyROGroup usm mynetwork
-
-####
-# Third, create a view for us to let the groups have rights to:
-
-# incl/excl subtree mask
-view all included .1 80
-
-####
-# Finally, grant the 2 groups access to the 1 view with different
-# write permissions:
-
-# context sec.model sec.level match read write notif
-access MyROGroup "" any noauth exact all none none
-access MyRWGroup "" any noauth exact all all none
-
-# -----------------------------------------------------------------------------
-
-
-###############################################################################
-# System contact information
-#
-
-# It is also possible to set the sysContact and sysLocation system
-# variables through the snmpd.conf file. **PLEASE NOTE** that setting
-# the value of these objects here makes these objects READ-ONLY
-# (regardless of any access control settings). Any attempt to set the
-# value of an object whose value is given here will fail with an error
-# status of notWritable.
-
-syslocation Right here, right now.
-syscontact Me <me@somewhere.org>
-
-# Example output of snmpwalk:
-# % snmpwalk -v 1 -c public localhost system
-# system.sysDescr.0 = "SunOS name sun4c"
-# system.sysObjectID.0 = OID: enterprises.ucdavis.ucdSnmpAgent.sunos4
-# system.sysUpTime.0 = Timeticks: (595637548) 68 days, 22:32:55
-# system.sysContact.0 = "Me <me@somewhere.org>"
-# system.sysName.0 = "name"
-# system.sysLocation.0 = "Right here, right now."
-# system.sysServices.0 = 72
-
-
-# -----------------------------------------------------------------------------
-
-
-###############################################################################
-# Process checks.
-#
-# The following are examples of how to use the agent to check for
-# processes running on the host. The syntax looks something like:
-#
-# proc NAME [MAX=0] [MIN=0]
-#
-# NAME: the name of the process to check for. It must match
-# exactly (ie, http will not find httpd processes).
-# MAX: the maximum number allowed to be running. Defaults to 0.
-# MIN: the minimum number to be running. Defaults to 0.
-
-#
-# Examples:
-#
-
-# Make sure mountd is running
-proc mountd
-
-# Make sure there are no more than 4 ntalkds running, but 0 is ok too.
-proc ntalkd 4
-
-# Make sure at least one sendmail, but less than or equal to 10 are running.
-proc sendmail 10 1
-
-# A snmpwalk of the prTable would look something like this:
-#
-# % snmpwalk -v 1 -c public localhost .EXTENSIBLEDOTMIB.PROCMIBNUM
-# enterprises.ucdavis.procTable.prEntry.prIndex.1 = 1
-# enterprises.ucdavis.procTable.prEntry.prIndex.2 = 2
-# enterprises.ucdavis.procTable.prEntry.prIndex.3 = 3
-# enterprises.ucdavis.procTable.prEntry.prNames.1 = "mountd"
-# enterprises.ucdavis.procTable.prEntry.prNames.2 = "ntalkd"
-# enterprises.ucdavis.procTable.prEntry.prNames.3 = "sendmail"
-# enterprises.ucdavis.procTable.prEntry.prMin.1 = 0
-# enterprises.ucdavis.procTable.prEntry.prMin.2 = 0
-# enterprises.ucdavis.procTable.prEntry.prMin.3 = 1
-# enterprises.ucdavis.procTable.prEntry.prMax.1 = 0
-# enterprises.ucdavis.procTable.prEntry.prMax.2 = 4
-# enterprises.ucdavis.procTable.prEntry.prMax.3 = 10
-# enterprises.ucdavis.procTable.prEntry.prCount.1 = 0
-# enterprises.ucdavis.procTable.prEntry.prCount.2 = 0
-# enterprises.ucdavis.procTable.prEntry.prCount.3 = 1
-# enterprises.ucdavis.procTable.prEntry.prErrorFlag.1 = 1
-# enterprises.ucdavis.procTable.prEntry.prErrorFlag.2 = 0
-# enterprises.ucdavis.procTable.prEntry.prErrorFlag.3 = 0
-# enterprises.ucdavis.procTable.prEntry.prErrMessage.1 = "No mountd process running."
-# enterprises.ucdavis.procTable.prEntry.prErrMessage.2 = ""
-# enterprises.ucdavis.procTable.prEntry.prErrMessage.3 = ""
-# enterprises.ucdavis.procTable.prEntry.prErrFix.1 = 0
-# enterprises.ucdavis.procTable.prEntry.prErrFix.2 = 0
-# enterprises.ucdavis.procTable.prEntry.prErrFix.3 = 0
-#
-# Note that the errorFlag for mountd is set to 1 because one is not
-# running (in this case an rpc.mountd is, but thats not good enough),
-# and the ErrMessage tells you what's wrong. The configuration
-# imposed in the snmpd.conf file is also shown.
-#
-# Special Case: When the min and max numbers are both 0, it assumes
-# you want a max of infinity and a min of 1.
-#
-
-
-# -----------------------------------------------------------------------------
-
-
-###############################################################################
-# Executables/scripts
-#
-
-#
-# You can also have programs run by the agent that return a single
-# line of output and an exit code. Here are two examples.
-#
-# exec NAME PROGRAM [ARGS ...]
-#
-# NAME: A generic name.
-# PROGRAM: The program to run. Include the path!
-# ARGS: optional arguments to be passed to the program
-
-# a simple hello world
-exec echotest /bin/echo hello world
-
-# Run a shell script containing:
-#
-# #!/bin/sh
-# echo hello world
-# echo hi there
-# exit 35
-#
-# Note: this has been specifically commented out to prevent
-# accidental security holes due to someone else on your system writing
-# a /tmp/shtest before you do. Uncomment to use it.
-#
-#exec shelltest /bin/sh /tmp/shtest
-
-# Then,
-# % snmpwalk -v 1 -c public localhost .EXTENSIBLEDOTMIB.SHELLMIBNUM
-# enterprises.ucdavis.extTable.extEntry.extIndex.1 = 1
-# enterprises.ucdavis.extTable.extEntry.extIndex.2 = 2
-# enterprises.ucdavis.extTable.extEntry.extNames.1 = "echotest"
-# enterprises.ucdavis.extTable.extEntry.extNames.2 = "shelltest"
-# enterprises.ucdavis.extTable.extEntry.extCommand.1 = "/bin/echo hello world"
-# enterprises.ucdavis.extTable.extEntry.extCommand.2 = "/bin/sh /tmp/shtest"
-# enterprises.ucdavis.extTable.extEntry.extResult.1 = 0
-# enterprises.ucdavis.extTable.extEntry.extResult.2 = 35
-# enterprises.ucdavis.extTable.extEntry.extOutput.1 = "hello world."
-# enterprises.ucdavis.extTable.extEntry.extOutput.2 = "hello world."
-# enterprises.ucdavis.extTable.extEntry.extErrFix.1 = 0
-# enterprises.ucdavis.extTable.extEntry.extErrFix.2 = 0
-
-# Note that the second line of the /tmp/shtest shell script is cut
-# off. Also note that the exit status of 35 was returned.
-
-# -----------------------------------------------------------------------------
-
-
-###############################################################################
-# disk checks
-#
-
-# The agent can check the amount of available disk space, and make
-# sure it is above a set limit.
-
-# disk PATH [MIN=DEFDISKMINIMUMSPACE]
-#
-# PATH: mount path to the disk in question.
-# MIN: Disks with space below this value will have the Mib's errorFlag set.
-# Default value = DEFDISKMINIMUMSPACE.
-
-# Check the / partition and make sure it contains at least 10 megs.
-
-disk / 10000
-
-# % snmpwalk -v 1 -c public localhost .EXTENSIBLEDOTMIB.DISKMIBNUM
-# enterprises.ucdavis.diskTable.dskEntry.diskIndex.1 = 0
-# enterprises.ucdavis.diskTable.dskEntry.diskPath.1 = "/" Hex: 2F
-# enterprises.ucdavis.diskTable.dskEntry.diskDevice.1 = "/dev/dsk/c201d6s0"
-# enterprises.ucdavis.diskTable.dskEntry.diskMinimum.1 = 10000
-# enterprises.ucdavis.diskTable.dskEntry.diskTotal.1 = 837130
-# enterprises.ucdavis.diskTable.dskEntry.diskAvail.1 = 316325
-# enterprises.ucdavis.diskTable.dskEntry.diskUsed.1 = 437092
-# enterprises.ucdavis.diskTable.dskEntry.diskPercent.1 = 58
-# enterprises.ucdavis.diskTable.dskEntry.diskErrorFlag.1 = 0
-# enterprises.ucdavis.diskTable.dskEntry.diskErrorMsg.1 = ""
-
-# -----------------------------------------------------------------------------
-
-
-###############################################################################
-# load average checks
-#
-
-# load [1MAX=DEFMAXLOADAVE] [5MAX=DEFMAXLOADAVE] [15MAX=DEFMAXLOADAVE]
-#
-# 1MAX: If the 1 minute load average is above this limit at query
-# time, the errorFlag will be set.
-# 5MAX: Similar, but for 5 min average.
-# 15MAX: Similar, but for 15 min average.
-
-# Check for loads:
-load 12 14 14
-
-# % snmpwalk -v 1 -c public localhost .EXTENSIBLEDOTMIB.LOADAVEMIBNUM
-# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.1 = 1
-# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.2 = 2
-# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.3 = 3
-# enterprises.ucdavis.loadTable.laEntry.loadaveNames.1 = "Load-1"
-# enterprises.ucdavis.loadTable.laEntry.loadaveNames.2 = "Load-5"
-# enterprises.ucdavis.loadTable.laEntry.loadaveNames.3 = "Load-15"
-# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.1 = "0.49" Hex: 30 2E 34 39
-# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.2 = "0.31" Hex: 30 2E 33 31
-# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.3 = "0.26" Hex: 30 2E 32 36
-# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.1 = "12.00"
-# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.2 = "14.00"
-# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.3 = "14.00"
-# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.1 = 0
-# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.2 = 0
-# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.3 = 0
-# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.1 = ""
-# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.2 = ""
-# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.3 = ""
-
-# -----------------------------------------------------------------------------
-
-
-###############################################################################
-# Extensible sections.
-#
-
-# This alleviates the multiple line output problem found in the
-# previous executable mib by placing each mib in its own mib table:
-
-# Run a shell script containing:
-#
-# #!/bin/sh
-# echo hello world
-# echo hi there
-# exit 35
-#
-# Note: this has been specifically commented out to prevent
-# accidental security holes due to someone else on your system writing
-# a /tmp/shtest before you do. Uncomment to use it.
-#
-# exec .EXTENSIBLEDOTMIB.50 shelltest /bin/sh /tmp/shtest
-
-# % snmpwalk -v 1 -c public localhost .EXTENSIBLEDOTMIB.50
-# enterprises.ucdavis.50.1.1 = 1
-# enterprises.ucdavis.50.2.1 = "shelltest"
-# enterprises.ucdavis.50.3.1 = "/bin/sh /tmp/shtest"
-# enterprises.ucdavis.50.100.1 = 35
-# enterprises.ucdavis.50.101.1 = "hello world."
-# enterprises.ucdavis.50.101.2 = "hi there."
-# enterprises.ucdavis.50.102.1 = 0
-
-# Now the Output has grown to two lines, and we can see the 'hi
-# there.' output as the second line from our shell script.
-#
-# Note that you must alter the mib.txt file to be correct if you want
-# the .50.* outputs above to change to reasonable text descriptions.
-
-# Other ideas:
-#
-# exec .EXTENSIBLEDOTMIB.51 ps /bin/ps
-# exec .EXTENSIBLEDOTMIB.52 top /usr/local/bin/top
-# exec .EXTENSIBLEDOTMIB.53 mailq /usr/bin/mailq
-
-# -----------------------------------------------------------------------------
-
-
-###############################################################################
-# Pass through control.
-#
-
-# Usage:
-# pass MIBOID EXEC-COMMAND
-#
-# This will pass total control of the mib underneath the MIBOID
-# portion of the mib to the EXEC-COMMAND.
-#
-# Note: You'll have to change the path of the passtest script to your
-# source directory or install it in the given location.
-#
-# Example: (see the script for details)
-# (commented out here since it requires that you place the
-# script in the right location. (its not installed by default))
-
-# pass .EXTENSIBLEDOTMIB.255 /bin/sh PREFIX/local/passtest
-
-# % snmpwalk -v 1 -c public localhost .EXTENSIBLEDOTMIB.255
-# enterprises.ucdavis.255.1 = "life the universe and everything"
-# enterprises.ucdavis.255.2.1 = 42
-# enterprises.ucdavis.255.2.2 = OID: 42.42.42
-# enterprises.ucdavis.255.3 = Timeticks: (363136200) 42 days, 0:42:42
-# enterprises.ucdavis.255.4 = IpAddress: 127.0.0.1
-# enterprises.ucdavis.255.5 = 42
-# enterprises.ucdavis.255.6 = Gauge: 42
-#
-# % snmpget -v 1 -c public localhost .EXTENSIBLEDOTMIB.255.5
-# enterprises.ucdavis.255.5 = 42
-#
-# % snmpset -v 1 -c public localhost .EXTENSIBLEDOTMIB.255.1 s "New string"
-# enterprises.ucdavis.255.1 = "New string"
-#
-
-# For specific usage information, see the man/snmpd.conf.5 manual page
-# as well as the local/passtest script used in the above example.
-
-###############################################################################
-# Subagent control
-#
-
-# The agent can support subagents using a number of extension mechanisms.
-# From the 4.2.1 release, AgentX support is being compiled in by default.
-# However, this is still experimental code, so should not be used on
-# critical production systems.
-# Please see the file README.agentx for more details.
-#
-# If having read, marked, learnt and inwardly digested this information,
-# you decide that you do wish to make use of this mechanism, simply
-# uncomment the following directive.
-#
-# master agentx
-#
-# I repeat - this is *NOT* regarded as suitable for front-line production
-# systems, though it is probably stable enough for day-to-day use.
-# Probably.
-#
-# No refunds will be given.
-
-
-###############################################################################
-# Further Information
-#
-# See the snmpd.conf manual page, and the output of "snmpd -H".
-# MUCH more can be done with the snmpd.conf than is shown as an
-# example here.
projects / bcm963xx.git / blobdiff