2 * include/asm-ia64/serial.h
4 * Derived from the i386 version.
7 #include <linux/config.h>
10 * This assumes you have a 1.8432 MHz clock for your UART.
12 * It'd be nice if someone built a serial card with a 24.576 MHz
13 * clock, since the 16550A is capable of handling a top speed of 1.5
14 * megabits/second; but this requires the faster clock.
16 #define BASE_BAUD ( 1843200 / 16 )
18 #define CONFIG_SERIAL_DETECT_IRQ /* on IA-64, we always want to autodetect irqs */
20 /* Standard COM flags (except for COM4, because of the 8514 problem) */
21 #ifdef CONFIG_SERIAL_DETECT_IRQ
22 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ)
23 #define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
25 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
26 #define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
29 #ifdef CONFIG_SERIAL_MANY_PORTS
30 #define FOURPORT_FLAGS ASYNC_FOURPORT
31 #define ACCENT_FLAGS 0
34 #define RS_TABLE_SIZE 64
39 #define MCA_COM_FLAGS STD_COM_FLAGS
42 * The following define the access methods for the HUB6 card. All
43 * access is through two ports for all 24 possible chips. The card is
44 * selected through the high 2 bits, the port on that card with the
45 * "middle" 3 bits, and the register on that port with the bottom
48 * While the access port and interrupt is configurable, the default
49 * port locations are 0x302 for the port control register, and 0x303
50 * for the data read/write register. Normally, the interrupt is at irq3
51 * but can be anything from 3 to 7 inclusive. Note that using 3 will
52 * require disabling com2.
55 #define C_P(card,port) (((card)<<6|(port)<<3) + 1)
57 #define STD_SERIAL_PORT_DEFNS \
58 /* UART CLK PORT IRQ FLAGS */ \
59 { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
60 { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
61 { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
62 { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
65 * HCDP_SERIAL_PORT_DEFNS should be placed in exactly the same slot
66 * in rs_table as defined by HCDP_SERIAL_CONSOLE_PORT in
67 * include/linux/serial.h
69 #define HCDP_SERIAL_PORT_DEFNS \
70 { 0, BASE_BAUD, -1, 0, STD_COM_FLAGS}, /* ttySx device
79 #ifdef CONFIG_SERIAL_MANY_PORTS
80 #define EXTRA_SERIAL_PORT_DEFNS \
81 { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
82 { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
83 { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
84 { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
85 { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
86 { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
87 { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
88 { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
89 { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
90 { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
91 { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
92 { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
93 { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
94 { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
95 { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
96 { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
97 { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
98 { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
99 { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
100 { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
101 { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
102 { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
103 { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
104 { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
105 { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
106 { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
107 { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
108 { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
110 #define EXTRA_SERIAL_PORT_DEFNS
113 /* You can have up to four HUB6's in the system, but I've only
114 * included two cards here for a total of twelve ports.
116 #if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
117 #define HUB6_SERIAL_PORT_DFNS \
118 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
119 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
120 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
121 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
122 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
123 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
124 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
125 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
126 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
127 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
128 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
129 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
131 #define HUB6_SERIAL_PORT_DFNS
135 #define MCA_SERIAL_PORT_DFNS \
136 { 0, BASE_BAUD, 0x3220, 3, MCA_COM_FLAGS }, \
137 { 0, BASE_BAUD, 0x3228, 3, MCA_COM_FLAGS }, \
138 { 0, BASE_BAUD, 0x4220, 3, MCA_COM_FLAGS }, \
139 { 0, BASE_BAUD, 0x4228, 3, MCA_COM_FLAGS }, \
140 { 0, BASE_BAUD, 0x5220, 3, MCA_COM_FLAGS }, \
141 { 0, BASE_BAUD, 0x5228, 3, MCA_COM_FLAGS },
143 #define MCA_SERIAL_PORT_DFNS
146 #define SERIAL_PORT_DFNS \
147 STD_SERIAL_PORT_DEFNS \
148 HCDP_SERIAL_PORT_DEFNS \
149 EXTRA_SERIAL_PORT_DEFNS \
150 HUB6_SERIAL_PORT_DFNS \